Bodyworx JX150HR Manuale utente
Treadmill
Model No:
1
Retain this owner’s manual for future reference
Read and follow all instructions in this owner’s manual
Version A
JX150HR
BODY WORX
BODY WORX
- 1 -
INDEX
1. OVERVIEW DRAWING 2
2. IMPORTANT SAFETY INSTRUCTIONS 3
3. GROUNDING INSTRUCTIONS 4
4. PRE-ASSEMBLY CHECK LIST 5
5. ASSEMBLY STEPS 6
6. CAUTION 8
7. MAINTENANCE 9
8. COMPUTER OPERATION INSTRUCTIONS 10
- 2 -
1. OVERVIEW DRAWING
電源線
機台主架
後調整盒
底座
電源開關
電源線
電子錶
Computer
Safety Key/ Clip
Power Switch
Circuit Breaker
Power Cord
Power Cord
Frame
Base
Rear End Cap
- 3 -
2. IMPORTANT SAFETY INSTRUCTIONS
When using this product, basic precautions should always be followed, including the following:
Please read the instruction carefully before starting to use this product.
Danger – To reduce the risk of electric shock：
1. Always unplug this product from the electrical outlet immediately after using and before
cleaning the treadmill.
Warning – To reduce the risk of burns, fire, electric shock, or physical injury：
1. The product should never be left unattended while plugged in.
Unplug the product from the outlet when not in use or before putting on or taking off
clothes and other belongings.
2. To avoid any danger, close supervision is necessary when this production is used by children,
invalids or disabled persons.
3. Be sure to use the product only for its intended use as described in this manual. Do not use any
attachment(s) not recommended by the manufacturer in order to avoid any danger or accidents.
4. Never operate the product if it has a damaged cord or plug, if it is not working properly, if it
has been damaged, or dropped into water. Please return the product to the service center or
seller for examination and repair.
5. Do not carry this product by the supply cord or use the cord as a handle.
6. Keep the cord away from hot surfaces or ground.
7. Never operate the product with the air vents blocked. Keep the air vents free of lint, hair, et cetera.
8. Never drop or insert any objects into any vent of the treadmill.
9. Do not use or operate outdoors.
10. Do not operate where aerosol (spray) products are being used or where oxygen is thin.
11. Before turning the product power off, turn all controls to the off position then remove the plug
from the outlet.
12. Connect the product to a properly grounded outlet only.
13. If the power cord is damaged, be sure to ask the manufacturer for replacement to avoid
accidents.
- 4 -
3. GROUNDING INSTRUCTIONS
Danger – Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or serviceman if you doubt whether the products
are properly grounded. Do not modify the plug provided with the product – if it will not fit the
outlet, have a proper outlet install by a qualified electrician.
The products is for use on normal 220V-240V circuit and contains a plug that looks like the
one illustrated in the figure. Make sure that the product is connected to an outlet having the same
configuration as the plug. No adapter should be used with the product.
Figure
Grounding methods
GROUNDED
OUTLET
GROUNDED PIN
The product must be grounded first. If malfunction or breakdown occurs, grounding will provide a
path of least resistance for electric current to reduce the risk of electric shock.
The product is equipped with an equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
- 5 -
4. PRE-ASSEMBLY CHECK LIST
a b c d e
fg
B
C
A
EFG
D
ITEM Description Qty ITEM
A Frame 1 a Truss Hex Screw M8xP1.25x40 2
B Left Decoration Cover 1 b Truss Hex Screw M8xP1.25x15 4
C Right Decoration Cover 1 c Truss Philips Screw M5xP0.8x20 6
D Bottle 1 d Plastic Washer Ø8xØ22x6t 4
E Cover-Left 1 e Hex Wrench + Screwdriver
5mm(70mmX70mm) 1
F Cover-Right 1 f Safety Key/Clip 1
G Cup Holder 2 g SLILCON 1
Description Qty
- 6 -
5. ASSEMBLY STEPS
Two persons are required to finish the
assembly steps.
(Caution!! Please follow exactly the
assembly steps below to avoid injury.)
1. Put up the two computer handrail tubes
of Frame (A) as shown in the right
drawing and tighten with hex screw (a).
PS. To avoid danger, always assemble
the treadmill with two or more persons,
do not assemble by yourself.
a
a
2. Then put up the left and right
uprights as shown in the right drawing
and tighten with hex screw(b).
PS. To avoid danger, always assemble
the treadmill with two or more
persons, do not assemble by yourself.
b
b
- 7 -
3. After tightened the left and right uprights,
insert left and right decoration covers (B,C)
onto frame respectively as the right drawing
shows and tighten with Philips Screw (c) and
Plastic Washer (d)
C
c
c
c
d
d
B
c
c
c
d
d
4. Wedge cup holder (G), left and right
covers (E,F) onto the corresponding position as
shown in the right drawing.
E
F
G
- 8 -
6. CAUTION
Note: The Cylinder contains high pressure gas.
Please avoid crash with other objects to avoid
danger.
Note: If the Cylinder is hit, it might be damaged
and cause the usage not smooth. The treadmill
might fall while folding.
This treadmill has the foldable mechanism for storage.
Stop all the movements (including stop the running belt
and take off the power cord) before storage, then pull out
the POP-Pin of the folding fixing mechanism as the
direction shown in the drawing and then lift up the frame
until the POP-Pin inserts into the frame. On the contrary,
if you want to use the treadmill, pull out the POP-Pin of
the folding mechanism as the arrow shows in the drawing
and put down the frame slowly.
(PS.1. To prevent from danger, be careful if the kids are
around.)
(PS.2. If you want to move the treadmill, fold the
treadmill at first, hold the rear adjust cap with your hands,
then lean the treadmill and do not move the treadmill
until the roller can be moved smoothly.)
(PS.3. Do not move the treadmill on uneven ground to
avoid danger.)
- 9 -
7. MAINTENANCE
1. If the belt tends to move off the center, stop the treadmill.
Take the Hex Wrench and adjust the Hex Screw in the Rear
End Cap. For example, if the running belt is moving towards
the left side, tighten the left Hex Screw about 1/4
turn(clockwise); if the running belt is moving towards the
right side, tighten the right Hex Screw about 1/4
turn(clockwise); Turn on the treadmill after it has been
adjusted. If you find that the belt has not moved to the proper
position, please repeat the steps above. Don’t use the treadmill
until the running belt returns to the center position.
(PS.1. This action is very important, if the belt is not in the
center, be sure to follow above steps.)
(PS.2. The position of running belt might not stay precisely in
the center with slightly towards the left and right sides,
and the situation varies with how end-users use and the
weight of end-users. No need to adjust the belt if it doesn’t
rub against the parts aside.)
2. Depending on the usage of the product, please apply
SILICON on the board according to the below chart. Use
the Hex Wrench to unscrew the bolt inside the Rear Roller.
Then pull the belt up and daub some SILICON to the center
of the board. After that, adjust the belt to the center of the
deck, followed by tightening the screw to the original set.
(PS.W hen the belt is sliding, please follow the above method
to lubricate the running belt. )
KGS/LBS Speed Interval
6KM/hr Below
6~12KM/hr
KGS
12KM/hr Above
4mile/hr Below
4~8mile/hr
LBS
8mile/hr Above
1 year
6 months
3 months
6 months
1 year
3 months
Note: This maintenance is intended for
household use.
If used for business, it is suggested to
examine the product every other month
Altri manuali Bodyworx Tapis roulant
Bodyworx
Bodyworx JI2040 Manuale utente
Bodyworx
Bodyworx J1600EA Manuale utente
Bodyworx
Bodyworx JI1825 Manuale utente
Bodyworx
Bodyworx JX335 Manuale utente
Bodyworx
Bodyworx J1325CAQ Manuale utente
Bodyworx
Bodyworx TM3000 Manuale utente
Bodyworx
Bodyworx SPORT3050 Manuale utente
Bodyworx
Bodyworx J1651EA Manuale utente
Bodyworx
Bodyworx JX735 Manuale utente
Bodyworx
Bodyworx J1530CA Manuale utente
Bodyworx
Bodyworx JT175 Manuale utente
Bodyworx
Bodyworx JSPORT3000 Manuale utente
Bodyworx
Bodyworx JX200 Manuale utente
Bodyworx
Bodyworx JX150 Manuale utente
Bodyworx
Bodyworx JX740 Manuale utente
Bodyworx
Bodyworx JTM2500 Manuale utente
Bodyworx
Bodyworx ATLANTA Manuale utente
Bodyworx
Bodyworx J1530CA Manuale utente
Bodyworx
Bodyworx JT8500 Manuale utente
Bodyworx
Bodyworx COLORADO175 Manuale utente
