Borg & Overstrom b5 Manuale utente
Contents
Page No Description
GB
Ambient
Chilled
Dispense Options
Chilled & Ambient
Chilled, Ambient & Sparkling
Chilled, Ambient & Hot
Chilled, Hot & Sparkling
Quick Start Guide
Page No
2
3
4
5
7
8
9
11
12
13
Description
Major Components
Water & CO2 Connection
CO2 Bottle Installation
Level Sensor Assembly
Cold Water Connection & Operation
Functions & Controls
General Safety
Isolation & Removal
Sanitisation Guide
Leak Dectection
Emptying The Carbonation Tank
Troubleshooting
Quick Start Guide
Borg & Overström GB2
Installation
Major Components
Water & CO2 Connection
Carbonation Switch
Chilled Switch
IEC Power Socket
CO2 Connector (1/4”)
Inlet Water (1/4”)
Drain Port
Left Table
Plate
Cold Tank
Right Table
Plate
Water Tap Set
Handle
Hot Power Switch
© Copyright Borg & Overström.
This manual is printed by Borg & Overström and shall not be reproduced or copied in anyway.
Drip Tray
IC Control Board
Leak Detector Reset
7
Level Sensor
Quick Start Guide
Borg & Overström GB3
CO2 Bottle Installation (Sparkling Versions Only)
IMPORTANT! ALWAYS ENSURE SECURITY CLIPS ARE
USED ON ALL WATER AND CO2 CONNECTIONS.
OFF
1
Attach the regulator to the
disposable CO2 bottle, ensuring
the regulator is closed. Connect
the CO2 bottle and regulator
to the machine using 1/4 inch
pipe.
COLD
2
After completing the water
installation, turn on the soda
power switch and the pump will
run. Do not open the regulator
valve until the carbonated switch
has been turned on.
We recommend between 3.5
- 5 bar. Do not exceed 5 bar
pressure.
5 Max bar
3
10 L
Flush through approximately 10
litres of water. Check and adjust
the CO2 pressure accordingly.
The machine needs leaving for
1 hour for sparkling water to
develop.
4
1
hour
Quick Start Guide
Borg & Overström GB4
Level Sensor Assembly
Check all parts are present.
1
Locate and connect the drainage
tubing into the top of the level sensor
connector.
2
The LED lighting at the base of the
faucet will ash slowly for 1 minute.
This is also repeataed every time a
dispense button is pressed.
3
Empty the waste container to cancel.
4
Quick Start Guide
Borg & Overström GB5
Operation
Water Connection & Operation
Connect and turn on the water
supply.
1
Plug in the power supply,
cold, hot & sparkling tanks will
automatically ll.
2
DLOC
Activate the carbonation & hot
power switch (if present).
3
Activate cold power switch.
DLOC
4
Quick Start Guide
Borg & Overström GB6
Flush through 10 litres of water
before use.
5
10 L
When the cold water switch is
turned on, the cold water and
chilling LED will be on.
hot
cold
chilling
heating
6
COLD
When the heating LED is off the
pre-set temperature has been
reached. This can take up to 30
minutes.
The temperature of cold water
can be set from 4c to 10c.
When the chilling LED is off
the set temperature has been
reached. This can take up to one
hour.
hot
cold
chilling
heating
7
4c
10 c
hot
cold
chilling
heating
8
Water Connection & Operation (Continued)
Quick Start Guide
Borg & Overström GB7
Functions & Controls
hot
cold
chilling
heating
General Safety
• Leave a space no less than
15cm between the wall and
dispenser.
• Keep the machine away from
sunlight, heat and moisture.
Hot Water Button Ambient Water Button Cold Water Button
Hot Water
Lock Button
Sparkling
Water
Button
(selected
models)
Quick Start Guide
Borg & Overström GB8
Maintenance & Cleaning
1
Please make sure the machine
is completely disconnected from
electricity before carrying out
any maintenance work.
2
Turn off the water supply.
3
To drain the Direct Chill tank, remove the cap on the back of the machine. We
recommend it is retted immediately upon draining being completed.
Cold water
drain
Isolation & Removal
Quick Start Guide
Borg & Overström GB9
Sanitisation Guide
NOTE: Before beginning the sanitation process please ensure that water is turned off at
the mains and refer to the MSDS document for further information. Use bioguard hand
gel and ensure gloves are worn.
hot
cold
chilling
heating
1
Briey press cold/ambient
dispense button to release
internal water pressure from
the machine. Remove the
existing lter.
2
Add 25 ml of Bioguard
Internal Sanitisation uid to a
clean and empty service lter
cartridge and connect to the
machine.
3
Turn on incoming water,
allow service cartridge to ll.
Dispense water using the cold
button until the water appears
pink. Briey press the ambient
button too. Repeat with
sparkling button if present.
PINK 4
Leave the solution inside
machine for sanitisation
to take effect (minimum 5
minutes) while thoroughly
cleaning the machine
externally, pay particular
attention to the dispense
faucet and button controls.
Quick Start Guide
Borg & Overström GB10
Sanitisation Guide (continued)
5
Remember to include the
drip tray. Empty the Waste
Overow system and ush
through with a small amount of
sanitisation uid if needed.
6
When the external cleaning
(minimum 5 minutes) is
completed, ush the machine
using the cold button with
clean water until the dispense
water runs clear. Repeat
briey with the ambient
button (and sparkling button if
present).
7
Turn off water and remove the
service lter. Retain service
lter for reuse. Fit new lter.
Turn on incoming water
supply.
8
Pre-ush the new lter to waste
using the ambient button until
the water appears clear and
is free of air. Flush through
a small amount of water to
check all functions.
Altri manuali per b5
1
Indice
Altri manuali Borg & Overstrom Distributore
Borg & Overstrom
Borg & Overstrom U2 Manuale utente
Borg & Overstrom
Borg & Overstrom u2 40L Manuale utente
Borg & Overstrom
Borg & Overstrom T2 Manuale utente
Borg & Overstrom
Borg & Overstrom T2 Manuale utente
Borg & Overstrom
Borg & Overstrom T1 Manuale utente
Borg & Overstrom
Borg & Overstrom C2 Manuale utente
Borg & Overstrom
Borg & Overstrom u1 Manuale utente
Borg & Overstrom
Borg & Overstrom T1 Tap systems Manuale utente
Borg & Overstrom
Borg & Overstrom B6 Manuale utente
