Bosch EDC17C46 Manuale utente

info@chiptuningshop.co.uk

Manual for using EDC17C46 Bosch ECU probe with MPPS – Page 1

1 Description: This probe can be used for programming VAG EDC17C4 Bosch ECU`s. It fits in most BDM

positioning frames and is fitted with LED`s for accurate alignment on the ECU. The “Boot” resistors and the

ignition feed can be switched. With this adapter, there is no need to solder at all

Adapter Overview

A = Serial port connection B = Power Switch ON/OFF

C = Power Jack D = DIP Switches for BOOT Resistors ON/OFF

E = Ignition selection switch:

ON > The ignition pin of the ECU is supplied with a constant 12V power supply

In conjunction with boot resistors switched OFF, use this mode for reading of password on TP8-10+, a so can be

used for DS Check, and genera diagnostic requests etc..

K-Line > The ignition pin of the ECU is connected directly to the K-Line of the flash tool

The f ash too wi power the ignition pin and automatica y cyc e the power when required to reset the processor.

In conjunction with boot resistors switched ON, use this mode for reading/writing over boot oader.

OFF > The ignition pin of the ECU is supplied with nothing

F = Connect to flash tool. G = Connect to serial port on probe (A)

Manual for using EDC17C46 Bosch ECU probe with MPPS – Page 2

2 Handling and Adjustment: IMPORTANT - Make sure that the power switch (B) is in the “OFF” position

The power switch must remain OFF so that the pins are not live, until the probe is correctly aligned and in

contact with the corresponding pins on the ECU Failure to follow these instructions could result in damage

to the ECU!

Place the probe into the BDM frame retaining bracket and tighten the screws. Attach the adapter cable (G) to

the serial port (A) on the probe and plug the other end (F) into the OBD cable of your flash tool. Connect the

power supply to the probe jack (C), the LED's will now turn on to aid alignment, however the probe does not

power the ECU until the power switch (B) is turned on.

Adjust the ECU on the frame and move the retainer carefully towards the ECU. Ensure that all the pins are in

their designated position.

A diagram showing the location of the connections can be found on page 3.

It is very important, that the retainer is free from backlash and moves smoothly!

3 Reading password: (This step is only necessary for TP8+) Lift up the Boot DIP switches (D) as shown in

the adapter overview on page 1 and set the Ignition switch (E) to the “ON” position, you can now read the

password.

4 Programming the ECU: Push the DIP switches (D) down and set the “Ignition” switch (E) to the “K-Line”

position, then you can proceed with programming over boot mode.

5 Disconnecting: To safely disconnect the probe from the ECU, you must first remove TURN OFF THE

POWER Switch (B) Once the power supply is disconnected it is safe to lift the frame and probe away from

the ECU.

Manual for using EDC17C46 Bosch ECU probe with MPPS – Page 3

The pads marked in yellow have to make contact with the probe

Technical alterations reserved!

This product should be operated by competent personnel only. Chiptuningshop Ltd do not accept any responsibility

for damages, direct or consequential caused by improper handling.

Indice

Altri manuali Bosch Adattatore

Bosch

Bosch Denoxtronic 2.2 Manuale utente

Bosch

Bosch Rexroth Fe PROFIBUS-DP Bus Adapter Manuale utente

Bosch

Bosch EasyControl Manuale utente

Bosch

Bosch Conettix D6680 Manuale utente

Bosch

Bosch Conettix D6672 Manuale utente

Bosch

Bosch Conettix ITS-D6682-INTL Manuale utente

Bosch

Bosch 1687846016 Manuale utente

Bosch

Bosch G 10 CL-1 Manuale utente

Bosch

Bosch GHA FC2 Professional Manuale utente

Bosch

Bosch Professional GFA 12-H Manuale utente

Bosch

Bosch GAA12V-21 Manuale utente

Bosch

Bosch ADT-NONH-G3QM33 Manuale utente

Bosch

Bosch EasyControl Istruzioni operative

Bosch

Bosch 1 687 023 777 Manuale di servizio

Bosch

Bosch Flasher LT Manuale utente

Bosch

Bosch G 10 CL-1 Manuale utente

Bosch

Bosch LTC 9213/01 Manuale utente

Bosch

Bosch GAA12V-21 Manuale utente

Bosch

Bosch EasyControl Manuale utente

Bosch

Bosch CDR 500 Kit Manuale utente

Bosch

Bosch T40234 Manuale utente

Bosch

Bosch Professional GAA 18V-48 Manuale utente

Bosch

Bosch GAA12V-21 Istruzioni per il montaggio

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente