Bosch ICP-SOL2-P Manuale utente
Control Panel
ICP-SOL2-P/ICP-SOL3-P
en User's Guide
Table of contents
1Introduction 5
2Specifications 6
3Codepad Introduction 7
3.1 Codepad 7
3.2 Quick Codepad Operation Instructions 7
3.3 Codepad Indicators 7
3.4 Audible Indications 9
4Operation with TEXT LCD Codepad 10
4.1 Text Menu 10
4.1.1 Command Menu 10
4.1.2 Access Menu 11
4.1.3 System Menu 11
4.1.4 Zone Menu 12
4.1.5 Area Menu 13
4.1.6 Output Menu 13
4.1.7 Communication Menu 13
4.1.8 Parameter Menu 14
5Operation with ICON LCD Codepad 15
5.1 Arming the System 15
5.1.1 Forced Arming 15
5.1.2 Arming in AWAY Mode 15
5.1.3 Arming in STAY Mode 1 16
5.1.4 Arming in STAY Mode 2 16
5.1.5 Programming STAY Mode 2 Zones 17
5.2 Disarming the System 17
5.3 User Codes 17
5.3.1 Adding User/Radio Codes 17
5.3.2 Deleting User/Radio Codes 17
5.4 Codepad Alarms 18
5.4.1 Codepad Duress Alarm 18
5.4.2 Codepad Panic Alarm 18
5.4.3 Codepad Fire Alarm 18
5.4.4 Codepad Medical Alarm 18
5.4.5 Codepad PIN Error (Access Denied) 18
5.5 Isolating Zones 18
5.5.1 Standard Isolating 18
5.5.2 Code to Isolate 19
5.6 Fault Analysis Mode 19
5.6.1 Fault Descriptions 20
5.7 Date and Time 21
5.8 Turning Outputs On/Off 22
5.9 Reset Latching Outputs 22
5.10 Telco Arm/Disarm Sequence (Call Forward On/Off) 22
5.10.1 Telco Arm Sequence 22
5.10.2 Telco Disarm Sequence 23
5.11 Testing 23
5.11.1 Horn Speaker Test 23
Control Panel Table of Contents | en 3
Bosch Security Systems, Inc. User's Guide 2014.05 | 01 | F01U298028
5.11.2 Bell Test 23
5.11.3 Strobe Test 24
5.11.4 Walk Test Mode 24
5.11.5 Test Report 24
5.12 Event Memory 24
5.13 Day Alarm 24
5.14 Codepad ID / Buzzer Tone 24
5.15 Remote Arming by Telephone 25
5.16 Domestic Dialing 25
5.16.1 Acknowledging Domestic Calls 25
5.16.2 Programming Domestic Telephone Numbers 26
5.16.3 Disable Domestic Dialing 26
6Glossary of Terms 27
4en | Table of Contents Control Panel
2014.05 | 01 | F01U298028 User's Guide Bosch Security Systems, Inc.
Introduction
Congratulations on selecting the ICP-SOL2-P/ICP-SOL3-P Control Panel to protect you and
your property. To obtain the most from your unit, take time to read through this manual and
familiarize yourself with the numerous outstanding operating features of this system. In all
aspects of planning, engineering, styling, operation, convenience, and adaptability, we have
sought to anticipate your every possible requirement.
Programming simplicity and speed were some of the major considerations and we believe that
our objectives in this area were more than satisfied.
This manual explains all aspects of operating the control panel. All system parameters and
options are detailed; however, suitability is left up to the individual. Every system can be
tailored to meet all requirements quickly and easily.
1
Control Panel Introduction | en 5
Bosch Security Systems, Inc. User's Guide 2014.05 | 01 | F01U298028
Specifications
Temperature Range 0℃ to +50℃
Humidity 20% to 90%
Power Source TF008 Plug Pack – 240 V/18 VAC @ 1.3A
Stand-By Current 65 mA
Current Draw in Alarm Condition 115 mA
Current Draw in Alarm Condition with
Codepad
105 mA
Back-Up Battery 7 Ah/12 VDC Rechargeable Sealed Lead Acid
Battery
Dimensions (Case, packed in carton) 306 mm x 262 mm x84 mm
Weight 2.5 kg
Supplier Code N771
Table 2.1: Specifications
Notice!
Test the sirens, strobe, and zones at weekly intervals.
2
6en | Specifications Control Panel
2014.05 | 01 | F01U298028 User's Guide Bosch Security Systems, Inc.
Codepad Introduction
Codepad
IUI – SOL -TEXT IUI – SOL – ICON
Quick Codepad Operation Instructions
Codepad Indicators
Codepad indicator
icons
Status Definition
ZONE 1 – 8 for ICP-
SOL2-P
ZONE 1 – 16 for ICP-
SOL3-P
On Zone is unsealed.
Off Zone is sealed.
Flashing Fast (0.25 sec
on/0.25 sec off)
Zone is in alarm condition.
Flashing Slow (1 sec on/1
sec off)
Zone is manually isolated or selected to
be isolated.
AWAY
On System is armed in AWAY Mode.
Off System is not armed in AWAY Mode.
Flashing twice a sec with
STAY indicator
Setting STAY Mode 2 zones.
3
3.1
3.2
3.3
Control Panel Codepad Introduction | en 7
Bosch Security Systems, Inc. User's Guide 2014.05 | 01 | F01U298028
Codepad indicator
icons
Status Definition
STAY
On System is armed in STAY Mode 1 or
STAY Mode 2.
Off System is not armed in STAY Mode 1 or
STAY Mode 2.
Flashing twice a sec Zone isolating mode
Flashing twice a sec with
AWAY indicator
Setting STAY Mode 2 zones.
Flashing once every 3 sec Day alarm status – day alarm turned on.
On System is disarmed.
MAINS
On AC MAINS power normal.
Flashing AC MAINS supply has failed.
FAULTS
On There is a system fault that needs to be
rectified.
Off The system is normal, there are no
faults.
Flashing There is a system fault that needs to be
acknowledged.
Programming Mode
Flashing These two indicators flash when you
enter Installer’s Programming Mode or
use any Master Code function.
The OFF indicator lights when the
system is disarmed and flashes when a
zone becomes unsealed when
disarmed. The indicator stops flashing
when all zones are sealed.
The ON indicator lights when the
system is armed and flashes when an
alarm occurs. The indicator is reset
after a valid User Code is entered.
8en | Codepad Introduction Control Panel
2014.05 | 01 | F01U298028 User's Guide Bosch Security Systems, Inc.
Audible Indications
Below table defines the audible indicators given out by the codepad buzzer.
Audible Indicator Definition
One short beep A button was pressed on the codepad, or Exit Time ended
when armed in STAY Mode 1 or STAY Mode 2.
Two short beeps The system accepted your code.
Three short beeps The requested function was executed.
One long beep Indicates the last 10 seconds of Exit Time when armed in AWAY
Mode, or the requested operation was denied or aborted.
Indicates codepad panic/fire/medical alarm operation.
One beep every sec Walk Test Mode is currently active.
One short beep every min There is a system fault waiting to be acknowledged.
One beep every 4 sec. During Auto Arming Pre-Alert Time, the warning before
automatic arming takes place.
One beep every 2 sec. During Exit Time when armed in AWAY Mode.
Table 3.1: Audible Indicators
3.4
Control Panel Codepad Introduction | en 9
Bosch Security Systems, Inc. User's Guide 2014.05 | 01 | F01U298028
Operation with TEXT LCD Codepad
Text Menu
Main Menu [ A U I ] 1 Command
[ U I ] 2 Access
[ U I ] 3 System
[ U I ] 4 Zone
[ I ] 5 Area
[ I ] 6 Output
[ I ] 7 Comm
[ I ] 8 Parameter
Table 4.1: Menu Structure
Text A or U or I in brackets [ ] instruct you the text menu that displays on the codepad for
different code holders:
[ A ] = All can access, no code required. To enter the text menu, simply press [ - ], only [1
Command] displays.
[ U ] = User code holder with authority levels can access. Enter the User Code, followed by
[ - ] to enter the menu.
[ I ] = Installer code holder can access. Enter the Installer Code, followed by [ # ] or [ - ] to
enter the menu, all menu items display.
Command Menu
[ A U I ] 1 Command
[ U ] 11 Arm [ U ] 111 AWAY Arm
[ U ] 112 STAY 1 Arm
[ U ] 113 STAY 2 Arm
[ U ] 114 AWAY Arm All
[ A U I ] 12 Inquire [ A U I ] 121 Fault Analysis
[ U I ] 122 Event Recall
[ A U I ] 13 System [ U ] 131 Set Date & Time
[ A U I ] 132 Day Alarm
[ U I ] 133 Arm/Disa Seq.
[ I ] 134 Report Monitor
[ A U I ] 135 ModemCall Init
[ U I ] 136 Domestic Phone
[ U I ] 137 VersionDisplay
[ I ] 138 FactoryDefault
[ U ] 139 System Reset
[ I ] 14 RF Diagnose
[ I ] 141 RF Zone
[ I ] 142 RF Keyfob
[ I ] 143 RF Repeater
4
4.1
4.1.1
10 en | Operation with TEXT LCD Codepad Control Panel
2014.05 | 01 | F01U298028 User's Guide Bosch Security Systems, Inc.
Altri manuali per ICP-SOL2-P
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Bosch Pannello di controllo
Bosch
Bosch Easy Series Manuale utente
Bosch
Bosch ICP-SOL2-P Manuale utente
Bosch
Bosch B5512 Manuale utente
Bosch
Bosch B8512G Manuale utente
Bosch
Bosch ICP-CC404 Manuale utente
Bosch
Bosch D9412GV2 Manuale utente
Bosch
Bosch FPA-1000-UL Manuale utente
Bosch
Bosch FPA-5000 Guida utente
Bosch
Bosch D7412G Manuale utente
Bosch
Bosch Easy Series Manuale utente
Bosch
Bosch Rexroth VAM 10.2 Manuale tecnico
Bosch
Bosch DS9400 Series Come usare
Bosch
Bosch MAP Control Center IUI-MAP0001-2 Manuale utente
Bosch
Bosch AMAX panel 2100 Manuale di istruzioni
Bosch
Bosch ICP-EZM2 Istruzioni per il montaggio
Bosch
Bosch K2200 Series Manuale utente
Bosch
Bosch B9512G Manuale utente
Bosch
Bosch AMAX panel 2000 ICP-AMAX-P Manuale utente
Bosch
Bosch D9412GV4 Manuale utente
Bosch
Bosch FPC-500 Manuale utente
