Bosch Solution 2000 Manuale del proprietario

Programming the BOSCH Solution 2000 & 3000 with the Icon

Keypad

This programming guide will show you the simplest steps required to program the basic

features of the system in order to make it operational for domestic use. Each programming

method assumes that you are not in programming mode, and that the system is in its

normal state and disarmed.

Press the button sequences inside the [ square brackets ] to complete the task at each

step in the method.

•Installer Code (default) = 1 2 3 4 (use this code to enter programming mode).

•User 1 Code (default) = 2 5 8 0 (this is also a master code).

Most of the required programming uses the following four-step method:

1. Enter programming mode: [1 2 3 4 # ] —two beeps sound and the Stay (person

inside house) and Away (person outside house) indicators flash on the keypad.

2. Go to the required location: [ loc. no. ] [ # ]

3. Change the data in that location (i.e., enter a number between 0 - 15), e.g.: [ 1 5 * ]

4. Save and exit programming mode: [ 9 6 0 # ] —or move to another location to make

more changes.

The alarm system stores information related to each feature at unique “locations”. Each

location will store a number between 0 - 15 that will indicate the option(s) selected for that

particular feature. Depending on the type of feature, the stored number may literally

represent the actual number (e.g., a number 1 may literally mean the number 1, which

will be the case for a user code location), or it may represent a specific function (e.g., a 1

may indicate that something is activated, selected, or turned on, which is the case for the

RF receiver location, where 1 means the RADION receiver has been set). Some

locations will require that you combine numbers to select multiple options. For example, if

option 1 means “Reporting functions allowed” and option 2 means “Remote arming by

telephone allowed”, then entering the number 3 at that location would select both of those

options, since 1 + 2 = 3.

Apart from programming mode, some settings can be programmed quickly via installer

code /master code operations, which require you to enter the code, followed by a

number representing the required operation, and then pressing [ # ] to confirm —three

beeps will sound and the Stay (person inside house) and Away (person outside house)

indicators flash on the keypad. For an example of this, please refer to “XV. Set Date &

Time.”

Page 1! of 12!

Before You Begin —Important Notes

•By default, Zone 8 is programmed to be a 24-hour tamper zone, which will activate the

sirens if the zone is unsealed, even if the alarm system is disarmed. If you are using a

Solution 2000, then your tampers should be assigned to Zone 8; we suggest you leave

the battery disconnected, close the lid on the metal enclosure, power up the system via

the AC power, default the panel, then temporarily change the zone type for Zone 8 to

“Not Used” whilst you finish programming (see “II. Assign Zone Types”). If you are

using a Solution 3000, your tampers will be assigned to Zone 16, so you can simply

seal Zone 8 by placing a 3K3 resistor across the Z8 and COM terminals.

•The system may power up in an armed state, so you will have to disarm the system

before you begin programming.

Arm/Disarm

Enter your user code and press [ # ] to arm or disarm the system, e.g., [2 5 8 0 # ]

Page !2 of !12

I. Default Panel

It is recommended that you default the panel to ensure you start with factory settings.

There are two methods for doing this:

Method 1

1. Enter programming mode: [1 2 3 4 # ]

2. Default the panel: [ 9 6 1 # ]

3. Save and exit: [ 9 6 0 # ]

Method 2

1. Disconnect the 12V battery and turn off the AC power transformer to shut down the

system’s power supply.

2. Hold down the default button on the panel PCB.

3. Reconnect power to the system (either AC or battery) and continue to hold down the

default button for at least 6 seconds.

4. Release the default button and the system will reset to default settings.

II. Assign Zone Types

You need to configure the zone type for each zone so that the system knows what each

zone is supposed to do, e.g., Should Zone 6 in the master bedroom set the alarm off

instantly if triggered whilst the system is armed?

Below are the basic zone types you will need to assign:

•Instant —When the system is armed, a zone with this zone type will activate the

sirens and strobe if it is triggered. Use an instant zone type for zones that should not

be accessed whilst the system is armed.

•Handover —When the system is armed, a zone with this zone type will carry on the

entry delay time if it is triggered after a zone with a delay zone type; if it is triggered

prior to a delay zone, it will activate the sirens and strobe. Use a handover zone type

for zones that may only be triggered following the triggering of a delay zone, and not

before.

•Delay-1 —This is the ideal zone type for the zone covering your primary entry point. It

will allow you time to disarm the system before activating the sirens and strobe, so long

as you pass through this zone first.

•24-Hour Tamper —Whether the system is armed or disarmed, if a zone with this

zone type is triggered, it will activate the sirens and strobe. You may wish to use this

on the zone that hosts your tamper switches; otherwise, an instant zone type will do.

Page !3 of !12

•Not Used —Assign this to zones that you do not intend to use, so that they

are removed from the system.

Each zone has a unique location that specifies its zone type. In order to select one of

the above zone types for a specific zone, you will need to enter its corresponding

number into the zone type location for that zone:

•0 = Instant

•1 = Handover

•2 = Delay-1

•9 = 24hr Tamper

•15 = Not Used

These are the locations for the zone types for all zones (including default zone types):󳆬

•Zone 1 = 267 (default = 2 —Delay-1)

•Zone 2 = 274 (default = 1 —Handover)

•Zone 3 = 281 (default = 1 —Handover)

•Zone 4 = 288 (default = 1 —Handover)

•Zone 5 = 295 (default = 0 —Instant)

•Zone 6 = 302 (default = 0 —Instant)

•Zone 7 = 309 (default = 0 —Instant)

•Zone 8 = 316 (default = 9 —24-Hour Tamper)

•Zone 9 = 323 (default = 15 —Not Used)

•Zone 10 = 330 (default = 15 —Not Used)

•Zone 11 = 337 (default = 15 —Not Used)

•Zone 12 = 344 (default = 15 —Not Used)

•Zone 13 = 351 (default = 15 —Not Used)

•Zone 14 = 358 (default = 15 —Not Used)

•Zone 15 = 365 (default = 15 —Not Used)

•Zone 16 = 372 (default = 15 —Not Used)

The following example will show you how to set up a standard system with Zone 1 as an

entry delay, Zone 2 as a “handover”, Zone 3 as an “instant”, Zones 4 - 8 as “not used”,

and Zone 16 as your tampers (Solution 3000):

1. Enter the text menu: [1 2 3 4 # ]

2. Enter address program: [ 8 1 ]

3. By default, Zone 1 is already set as Delay-1, so we can leave it.

4. By default, Zone 2 is already set as a Handover, so we can leave it.

Page !4 of !12

5. Go to the location of the zone type for Zone 3: [ 2 8 1 # ]

6. Change the 1 (Handover) to a 0 (Instant): [ 0 * ]

7. Go to the location of the zone type for Zone 4: [ 2 8 8 # ]

8. Change the 1 (Handover) to a 15 (Not Used): [ 1 5 * ]

9. Go to the location of the zone type for Zone 5: [ 2 9 5 # ]

10. Change the 0 (Instant) to a 15 (Not Used): [ 1 5 * ]

11. Go to the location of the zone type for Zone 6: [ 3 0 2 # ]

12. Change the 0 (Instant) to a 15 (Not Used): [ 1 5 * ]

13. Go to the location of the zone type for Zone 7: [ 3 0 9 # ]

14. Change the 0 (Instant) to a 15 (Not Used): [ 1 5 * ]

15. Go to the location of the zone type for Zone 8: [ 3 1 6 # ]

16. Change the 9 (24-Hour Tamper) to a 15 (Not Used): [ 1 5 * ]

17. Zones 9 - 15 are set as “Not Used” by default, so can be left as they are.

18. Go to the location of the zone type for Zone 16: [ 3 7 2 # ]

19. Change the 15 (Not Used) to either a 9 or 0: [ 9 * ] or [ 0 * ]

20. Save and exit programming mode: [ 9 6 0 # ]

To further elaborate, using Zone 3 as an example:

1. We went to the location of the zone type for Zone 3: [ 2 8 1 # ]. The number 1 was in

that location, indicating that the zone type for Zone 3 was a handover.

2. We changed the 1 (Handover) to a 0 (Instant): [ 0 * ]

Using the above information, make the necessary programming changes to your system. If

you are using a Solution 2000, only zones 1 - 8 can be used, so you should use Zone 8 as

your tamper zone, which is already a 24-hour tamper by default.

III.Handover Delay Sequential

If you have zones with a handover zone type, those handover zones must be triggered

in order (i.e., Zone 2, Zone 3, etc.) following a delay zone in order to carry on its entry

time, otherwise an alarm will activate. If you require a system with handover zones that

may be triggered out of order following a delay zone (e.g., Zone 3, Zone 2), then you

may choose handover delay to be non-sequential:

1. Enter programming mode: [1 2 3 4 # ]

2. Go to the location for System Options 3: [ 4 9 4 # ]

3. Change the 8 to a 0: [ 0 * ]

4. Save and exit: [ 9 6 0 # ]

Options

Page !5 of !12

•8 = Handover delay to be sequential

•0 = Handover delay to be non-sequential

IV. Change Entry Time 1

Entry Time 1 is the time specified for a zone with a Delay-1 zone type. You can change

this time by programming two locations: 466 & 467 —combining the time set in these two

locations will give you the total time specified for Entry Time 1. Location 466 uses

increments of 1 second, with a maximum of 15 seconds; location 467 uses 16-second

increments, with a maximum of 240 seconds, since the greatest value you can enter into

a location is 15 (i.e., 16 secs x 15 = 240 secs).

The following example will show you how to program a time of 60 seconds for

Entry Time 1:

1. Enter programming mode: [1 2 3 4 # ]

2. Go to the first location for Entry Time 1: [ 4 6 6 # ]

3. Enter a time of 12 seconds: [ 1 2 * ]

4. Go to the second location for Entry Time 1: [ 4 6 7 # ]

5. Specify a time of 48 seconds by selecting three 16-second increments: [ 3 * ]

6. Save and exit: [ 9 6 0 # ]

Combining the time of 12 seconds in location 466 with the 48 seconds in location 467

gives a total time of 60 seconds for Entry Time 1. Thus, allowing 60 seconds to disarm

the alarm system upon entry through a Delay-1 zone.

V. Change Exit Time

Once you have registered your desire to arm the alarm system, exit time is the amount of

time allowed before the system arms (a long tone will indicate the final 10 seconds of the

countdown when arming in Away mode).

Again, two locations must be programmed: 470 (increments of 1 second) and 471

(increments of 16 seconds).

The following example will show how to program the exit time to allow 120 seconds

(2 minutes):

1. Enter programming mode: [1 2 3 4 # ]

2. Go to the first location for Exit Time: [ 4 7 0 # ]

3. Enter a time of 8 seconds: [ 8 * ]

4. Go the the second location for Exit Time: [ 4 7 1 # ]

5. Specify a time of 112 seconds by selecting seven 16-second increments: [ 7 * ]

6. Save and exit: [ 9 6 0 # ]

Page !6 of !12

Combining the time of 8 seconds in location 470 with the time of 112 seconds specified in

location 471 will give a total exit time of 120 seconds.

VI. Set Stay Mode 1

Stay Mode 1 can be used to have the system partially armed with some zones isolated,

whilst others remain active. This is ideal if you still want some zones armed whilst you are

at home, especially at night when you are sleeping, e.g., doors, windows, bottom storey,

back rooms, shed, garage —zones unlikely to be entered by household members.

You can specify which zones are to be isolated in Stay Mode 1 by selecting the option

“Isolated in Stay Mode 1” in Zone Options 2 for the required zone. Each zone stores its

Zone Options 2 information at a unique location.

These are the locations for Zone Options 2 for each zone:

• Zone 1 = 271

• Zone 9 = 327

• Zone 2 = 278

• Zone 10 = 334

• Zone 3 = 285

• Zone 11 = 341

• Zone 4 = 292

• Zone 12 = 348

• Zone 5 = 299

• Zone 13

= 355

• Zone 6 = 306

• Zone 14

= 362

• Zone 7 = 313

• Zone 15

= 369

• Zone 8 = 320

• Zone 16

= 376󳆬

To select a zone for isolation in Stay Mode 1, you must enter a 15 at its location for Zone

Options 2.

For example, to have Zone 5 isolated in Stay Mode 1:

1. Enter programming mode: [1 2 3 4 # ]

2. Go to the location of Zone Options 2 for Zone 5: [ 2 9 9 # ]

3. Change the 14 to a 15: [ 1 5 * ]

4. Save and exit: [ 9 6 0 # ]

You can arm the alarm system in Stay Mode 1 by either holding down the [ * STAY ]

button for three seconds, or by entering your user code and pressing [ * STAY ], e.g., [

25 8 0 * ]. The isolated zones will flash on the keypad and the Stay (person inside

house) indicator will display.

VII. Change Installer Code

Each number of the installer code is stored in its own location. There are four locations:

Page !7 of !12

•181 (default number = 1)

•182 (default number = 2)

•183 (default number = 3)

•184 (default number = 4)

You need to change the number in each location to change the installer code.

The following example will show you how to change the installer code from 1 2 3 4

to 6789:

1. Enter programming mode: [1 2 3 4 # ]

2. Go to the location for the first number: [ 1 8 1 # ]

3. Change the 1 to a 6: [ 6 * ]

4. Go to the location for the second number: [ 1 8 2 # ]

5. Change the 2 to a 7: [ 7 * ]

6. Go to the location for the third number: [ 1 8 3 # ]

7. Change the 3 to an 8: [ 8 * ]

8. Go to the location for the fourth number: [ 1 8 4 # ]

9. Change the 4 to a 9: [ 9 * ]

10.Save and exit: [ 9 6 0 # ]

The installer code has now been changed to 6 7 8 9, so you will need to press [ 6 7 8 9

# ] in order to enter programming mode. However, we will continue to use the default

installer code of 1 2 3 4 throughout this guide.

VIII. Add/Delete User Codes

User codes are also stored across four locations, but you can change them easily by using

the master code (MC) operation [ MC 1 # ] and changing the code for the required user.

Since User 1 is a master code by default, it can be used to complete this operation.

For example, to change the code for User 1 from 2 5 8 0 to 3 0 1 5:

1. Enter the user master code operation: [2 5 8 0 1 # ]

2. Specify the user number (1 - 32) you want to change the code for: [ 1 # ]

3. Enter the new code: [ 3 0 1 5 # ]

The code for User 1 has been changed to 3 0 1 5, however, we will continue using the

default master code of 2 5 8 0 throughout this guide.

If you wish to delete a user code:

1. Enter the user master code operation: [2 5 8 0 1 # ]

Page !8 of !12

2. Specify the user number (1 - 32) you want to delete the code for, e.g.: [ 8 # ]

3. Press the [ * ] button to delete it.

IX. Assign RF Receiver

You must specify the RF receiver to be used if you intend to use RF devices, such as

remote key fobs or wireless detectors —this can be done at location 395.

Options

•0 = Not Used

•1 = Use RADION (Solution 3000 only)

•2 = Use WE800EV2 (Solution 2000)

For example, to assign a RADION B810 as the RF receiver:

1. Enter programming mode: [1 2 3 4 # ]

2. Go to the location for receiver assignment: [ 3 9 5 # ]

3. Select option 1: [ 1 * ]

4. Save and exit: [ 9 6 0 # ]

X. Add/Delete RF Key Fobs

Adding a key fob is similar to adding a user code, except that you enter a key fob RFID

number, instead of a PIN code. Additionally, key fob numbers are between the range of

301 - 332, as opposed to 1 - 32 for user codes.

To add a RADION key fob:

1. Make sure you have assigned the RADION receiver.

2. Enter the user master code operation: [2 5 8 0 1 # ]

3. Enter the user number (301 - 332) you wish to assign the key fob to, e.g.: [ 3 0 1 # ]

4. Enter the nine-digit RFID number on the key fob, e.g.: [ 1 2 3 4 5 6 7 8 9 # ]

5. Press [ # ] to confirm the operation and exit.

To delete a RADION key fob:

1. Enter the user master code operation: [2 5 8 0 1 # ]

2. Enter the key fob number (301 - 332) you want to delete, e.g.: [ 3 0 1 # ]

3. Press the [ * ] button to delete it.

Page !9 of !12

XI. Adjust External Siren Beep Volume for Key Fob Arm/Disarm

When you arm/disarm the system via a remote key fob, the external siren beeps briefly

to acknowledge this.

You can adjust the volume of these beeps (0 = no beeps, 15 = loudest beeps;

default = 13):

1. Enter programming mode: [1 2 3 4 # ]

2. Go to the location for Speaker Beep Volume: [ 4 9 1 # ]

3. Select a volume, e.g., no beeps: [ 0 * ]

4. Save and exit: [ 9 6 0 # ]

XII. Strobe Indication for Key Fob Arm/Disarm & Assign Key Fob

Button to Arm Stay Mode 1

If you still wish the strobe light to indicate when you arm/disarm via remote key fob, you

can program that feature in; additionally, you can program the fourth button on the remote

key fob to be able to arm the system in Stay Mode 1 —both features are stored at the

location for System Options 1.

1. Enter programming mode: [1 2 3 4 # ]

2. Go to the location for System Options 1: [ 4 9 2 # ]

3. Change the 1 to a 13: [ 13 * ]

4. Save and exit: [ 9 6 0 # ]

Options

•Default = 1

•Strobe Indication via Remote Arm/Disarm = 4

•Button 4 Stay Mode 1 = 8

Thus, 1 + 4 + 8 = 13

XIII. Add/Delete RF Device (Wireless Zones)

If you need to add RADION PIR detectors and other wireless RF devices, you can do so

using the following installer code operation:

1. Make sure you have assigned the RADION receiver.

2. Enter the RF device installer code operation: [1 2 3 4 0 # ]

3. Enter the zone number (1 - 16) that you wish to assign the RF device to, e.g.: [ 9 # ]

4. Enter the nine-digit RFID number on the RF device, e.g.: [ 1 2 3 4 5 6 7 8 9 # ]

5. Specify the RF zone option (can be left as 0 = All, or as 1 = Input 1): [ 0 # ]

Page !10 of !12

Altri manuali per Solution 2000

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Bosch Sistema di sicurezza

Bosch

Bosch HSG9483 Series Manuale utente

Bosch

Bosch SE 60 LSNi Manuale utente

Bosch

Bosch Plena Power Amplifier Manuale utente

Bosch

Bosch FMC-210-DM-G-R Manuale utente

Bosch

Bosch SE 320 LSNi Manuale utente

Bosch

Bosch CCS 800 Ultro Manuale utente

Bosch

Bosch BRS Manuale utente

Bosch

Bosch VSS7915/00T Manuale utente

Bosch

Bosch D420 Manuale utente

Bosch

Bosch DIVAR IP all-in-one 7000 3U Manuale utente

Bosch

Bosch D2000 Manuale utente

Bosch

Bosch ISW-BHB1-WX Manuale di servizio

Bosch

Bosch LTC 8540/00 Manuale utente

Bosch

Bosch MBV-BPRO-45 Foglio di istruzioni

Bosch

Bosch DIP-2040-00N Manuale utente

Bosch

Bosch DB24C4200R2 Manuale utente

Bosch

Bosch Plena LBB 1965 Manuale utente

Bosch

Bosch ISN-SM-30 Guida utente

Bosch

Bosch PAVIRO Istruzioni per il montaggio

Bosch

Bosch DS937 Manuale utente

Bosch

Bosch ICP-MAP5000-2 Manuale utente

Bosch

Bosch 844 Manuale utente

Bosch

Bosch AVENAR all-in-one 4000 Manuale utente

Bosch

Bosch Divar Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente