BraunAbility HAL2 Manuale utente
HAND ACTUATED
LOCKABLES
User Manual
EN Instructions for tting and use
2HAL2, HAL3
Thank you for choosing
Hand Actuated Lockables
from BraunAbility!
The following manual is an important part of the product, providing
you with information on how to achieve maximum performance
and safe operation. Keep the manual in a safe place so that you can
refer to it when necessary.
If you have any questions about your equipment, please contact us.
Once again, thank you for placing your condence in our products!
Safe vehicle adaptation solutions
For your safety BraunAbility products are
designed and tested according to current
directives and standards.
Safety information
Fit and use
After care
Limitation of use
Fitting the Hand Actuated Lockable (HAL) to the seat leg
Adjusting HAL setting to the rail
Operating HAL
Equipment storage and maintenance
Warranty
4
6
8
10
12
12
3
HAL2, HAL3
EN
Index
“Declaration of conformity” at the end of the manual.
Limitation of use
Safety information
4HAL2, HAL3
HAL2 - 2 Fixing Studs HAL3 - 3 Fixing Studs
5
HAL2, HAL3
EN
Fit and use
Fitting the Hand Actuated Lockable (HAL) to the seat leg
Fit and use
1. First, remove all M10 nyloc nuts and washers from sliding stud assemblies with a 17mm wrench (Fig. 1).
2. Ensure the seat is placed facing towards the front of the vehicle. Fit sliding studs through the seat leg bracket
holes as shown above. Position both seat legs at approximately 5mm (1/4”) from the front of the handle, ensuring
alignment (Fig. 2).
3. Replace all washers and nuts and loosely fasten with a 17mm wrench (Fig. 3). Finally tighten the M10 nyloc nuts with
a torque wrench to a recommended torque of : 35-40Nm (18-22lb.ft)
Note: Two removable seat xtures are normally required for each seat. It is important
that the seat legs are set to the identical rail width where the seat is to be tted.
Both HAL need to be aligned parallel to each other in the rail.
6HAL2, HAL3
WARNING
In 3 stud version, the rear most xing MUST NOT be used in isolation.
If it is intended that the seat should face the rear, please contact BraunAbility.
M10 Nyloc Nut
17mm wrench
M10 Nyloc Nut
17mm wrench
Sliding Stud
Seat Leg
Front of Vehicle
Figure 1 Figure 2 Figure 3
7
HAL2, HAL3
EN
Fit and use
Adjusting HAL setting to the rail
Fit and use
HAL lockable comes with variable adjustable setting to accommodate different rail proles and
thicknesses. Each setting relates to a different thickness depth.
Setting 1: Thinner Rail Setting 2: Standard Rail Setting 3: Thicker Rail
1. Once HAL has been tted to the seat leg, check that the lockables are on the right setting to
t the rail in your vehicle.
2. Place the seat in the rail with HAL unlocked (Fig. 4).
3. Try and lock the seat by pushing the handle forward to the locked position (Fig. 5):
A. The handle locks smoothly and the seat doesn’t rattle; HAL is set correctly.
B. The handle is difcult to push forward; looking from the front, adjust HAL by inserting a
3mm allen key and rotating half turn clockwise . Once this is done try locking HAL again.
(Repeat operation as necessary).
C. The handle locks too easily and rattles; looking from the front, adjust HAL by inserting a
3mm allen key and rotating half turn anti-clockwise. Once this is done try locking HAL again.
(Repeat operation as necessary).
IMPORTANT: Tighten by hand only. Do not use tools of any kind.
8HAL2, HAL3
Setting
Adjustment
Unlock Lock
Figure 4 Figure 5
9
HAL2, HAL3
EN
Fit and use
Operating HAL
Fit and use
1. Before locating the seat into the rail, unlock HAL, by pressing the silver trigger
(Fig 6) and then pull the handle fully back (Fig 7).
2. To locate the seat in the rail, align both HAL wheels into the rail, tilt the seat
backwards slightly and wheel it along the rail to the right location. Once this is
found, lower the seat into the rail gently push it forwards or backwards until it
is located into the rail.
3. To lock the seat into the rail, push the handle forward to the upright position
(Fig 8) until you hear it click.
Anti-tamper device
The anti-tamper device, which is supplied with HAL, is an optional accessory.
1. Should you choose to use this device during transportation, just clip it on to
the silver trigger, making sure it is safely tted (Fig 9).
2. To remove the device, simply push it sideways to release the silver trigger.
Stow away securely.
Removing seat from rail
1. To release the seat from the rail,
unlock HAL, by pushing handle
forward while pressing the silver
trigger (Fig 6), then pulling the
handle fully back (Fig 7).
2. Tip the seat backwards and
remove from the rail.
10 HAL2, HAL3
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali BraunAbility sedia a rotelle
BraunAbility
BraunAbility P-LBS Manuale utente
BraunAbility
BraunAbility KIT9 Manuale utente
BraunAbility
BraunAbility T-WBB Manuale utente
BraunAbility
BraunAbility EASISIT Manuale utente
BraunAbility
BraunAbility Turny 6-Way Manuale utente
BraunAbility
BraunAbility 3 Point Retractable Occupant Restraint Manuale utente
BraunAbility
BraunAbility RQ10MH Manuale utente
BraunAbility
BraunAbility TOR HD QUATTRO EXPRESS Manuale utente
BraunAbility
BraunAbility PIN AND PIN HEAVY-DUTY Manuale utente
BraunAbility
BraunAbility DI-RQ10PK Manuale utente
BraunAbility
BraunAbility T-RQ10PK Manuale utente
BraunAbility
BraunAbility DI-RQMH Manuale utente
BraunAbility
BraunAbility P-SABB Manuale utente
BraunAbility
BraunAbility RBC Manuale utente
BraunAbility
BraunAbility KIT 8 Manuale utente
BraunAbility
BraunAbility Carony Series Manuale utente
BraunAbility
BraunAbility Carolift 100 Manuale utente
BraunAbility
BraunAbility T-ROBK Manuale utente
BraunAbility
BraunAbility I-SQE16MK Manuale utente
BraunAbility
BraunAbility I-RQE10MK Manuale utente
