BraunAbility KIT 8 Manuale utente
KIT5 & KIT 8
User Manual
EN Instructions for tting and use
2KIT5 & KIT8
Thank you for choosing
KIT5 & KIT8
from BraunAbility!
The following manual is an important part of the product, providing
you with information on how to achieve maximum performance
and safe operation. Keep the manual in a safe place so that you can
refer to it when necessary.
If you have any questions about your equipment, please contact us.
Safe vehicle adaptation solutions
For your safety BraunAbility products are
designed and tested according to current
directives and standards.
Safety information
Fit and use
After care
Limitations of use
General guidance
Fitting the wheelchair & occupant restraint kits
Front tie-downs - KIT5
Rear tie-downs - KIT5
Equipment storage and maintenance
Warranty
4
6
10-15
10
12
14
16
20
3
KIT5 & KIT8
EN
Index
“Declaration of conformity” at the end of the manual.
Limitation of use
Safety information
The development of BraunAbility kits is a continuous process. Applications
are added on a regular basis. For more details contact BraunAbility or look
on the BraunAbility website.
4KIT5 & KIT8
KIT5
5
KIT5 & KIT8
EN
Safety information
General guidance
• Wheelchair Accessories that have not been approved by the Wheelchair Manufacturer
must be removed from the wheelchair and secured in the vehicle during transport to
reduce the potential for injury. Refer to ‘Instructions For Use in Transport’ provided with
the wheelchair or contact wheelchair manufacturer for further guidance.
•
(test dummy) with a mass of 76.3kg. The test dummy was restrained by both a pelvic and
upper-torso restraint. Use of a pelvic only belt may compromise the performance of the
WTORS system and should be avoided.
• If the installation is to be used with an occupant head rest anchored to the vehicle, then
wheelchair seatback, preventing neck injury.
• Regular inspection of all parts is recommended and the equipment should be used only if
all components are in good condition.
• Warning: protect webbing from contacting sharp edges and corners. Replace equipment
if the webbing does becomes cut, contaminated or frayed.
6KIT5 & KIT8
• Any restraints which have been subjected to a crash situation from which the vehicle must
be towed, should, in the interest of safety, be replaced.
•
this tie-down, please contact BraunAbility. Please read this manual fully before use.
• Avoid contact with corrosive liquids. Care should be taken to prevent contamination of the
webbing with polishes, oils and chemicals.
•
converter. Anchorages should not be installed into unsound materials such as corroded
•
BraunAbility, and any deviation from the recommendations here is the responsibility of the
7
KIT5 & KIT8
EN
Safety information
Before tting the wheelchair & occupant restraint kits
• Ensure that the wheelchair is correctly maintained and that the settings of any adjustable
parts are made according to ‘Instructions for Use in Transport’.
• Whenever possible remove any items of luggage etc that may be attached to the wheelchair
and secure or store separately during transport in order to reduce the potential for injury to
other passengers travelling in the vehicle.
• Extra care must be exercised when using vehicle boarding aids such as passenger lifts or
ramps during the loading process. Refer to ‘Instructions For Use’ for information on safe
slopes.
• Position the wheelchair facing forward - centrally in the designated region of the vehicle.
Ensure the wheelchair brakes are applied.
• To minimise the potential for head injuries in an impact, allow a clear space of at least 400
mm behind and 650 mm, (FCZ, front clear zone), in front of the head of the wheelchair
user, (Fig A). The shoulder belt anchorage must be roof or side-wall anchored at a height
level such that the belt webbing passes over the midpoint of the occupant shoulder and
at a height that is at or just above the level of the occupants shoulders so as not to impose
downward loads on the spine.
• A height provision (HHT) ranging from 1000mm to 1550mm should be made, depending
on the size of the passenger. There should also be 200 mm of clear space either side of
the wheelchair centre line. If these clear space dimensions cannot be provided then any
should be adequately padded and comply with impact performance requirements of
Note: seated head
height (HHT)
ranges from as low
as 1000mm for a
6-year-old child to
1550mm for a tall
adult.
KIT5 & KIT8
• Wheelchair users, their carers and family are advised to check vehicle
accommodate the wheelchair and tie-down system. These distances
are based upon the desire to maintain clear zones for potential head
excursions of occupants provided with both upper and lower torso
restraints.
• Users of heavy powered wheelchairs are also advised to check vehicle
carrying capacity. If in doubt consult the vehicle supplier for further
details.
•
supplementary occupant restraint if designed to be used in
combination with the wheelchair tie-down.
• Installers of this tie-down should take note of any vehicle airbag
position when planning the installation. Airbags can cause serious
injury if a wheelchair-seated occupant is seated too close to an airbag
position. If in doubt contact the vehicle manufacturer or your National
Automotive Regulatory Body for advice.
Figure A
9
KIT5 & KIT8
EN
Safety information
Fitting the wheelchair & occupant restraint kits - KIT5
Fit and use
Front tie-downs
1. The rail will have been installed in the vehicle in accordance with our own and
the vehicle converter’s instruction. Position the wheelchair within the vehicle
as required.
2.
aligning the ATF feet with the cut-out sections of the rail, and locate into the
rail, (Fig 1).
3.
wheelchair until the yellow plunger drops and locks into the rail.
4. Install the second front tie-down ATF in the same way, ensuring that each
ATF positioning.
5. Press the red buckle button(s) to release the webbed tongue, extend and
pass around each of the front wheelchair frame tie-down points, (Fig 2), (some
wheelchairs will indicate these tie-down positions, Fig 3). Reconnect the
tongue back into the buckle, creating an angle of around 40 to 60° within the
front view zone, (Fig 4).
6. Release the wheelchair brakes and pull back to tension the front tie-downs.
Re-apply the brakes.
Removing the front tie-down
IMPORTANT: First remove the rear
tie-downs, as instructed on pages 12
and 13.
1. Once the rear tie-downs have
been removed, press the red
buckle release button to release
the webbed tongue. Pass back
through the front wheelchair frame
tie-down points and return the
tongue to the buckle.
2. Lift the ATF yellow plunger fully
and slide back away from the
wheelchair to align the ATF feet
with the rail cut-outs, lift away from
the rail.
Note: in an emergency, the front
tie-downs can be released from
the wheelchair without the need
to slacken the rears by simply
pressing the red buckle release
button.
10 KIT5 & KIT8
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali BraunAbility sedia a rotelle
BraunAbility
BraunAbility P-SABB Manuale utente
BraunAbility
BraunAbility Turny 6-Way Manuale utente
BraunAbility
BraunAbility Carony Series Manuale utente
BraunAbility
BraunAbility PIN AND PIN HEAVY-DUTY Manuale utente
BraunAbility
BraunAbility T-WBB Manuale utente
BraunAbility
BraunAbility DI-RQ10PK Manuale utente
BraunAbility
BraunAbility P-LBS Manuale utente
BraunAbility
BraunAbility Under-Vehicle Lift NUSP34S31X48RWO Manuale utente
BraunAbility
BraunAbility EASISIT Manuale utente
BraunAbility
BraunAbility T-ROBK Manuale utente
BraunAbility
BraunAbility DI-RQMH Manuale utente
BraunAbility
BraunAbility 3 Point Retractable Occupant Restraint Manuale utente
BraunAbility
BraunAbility Carolift 100 Manuale utente
BraunAbility
BraunAbility TOR HD QUATTRO EXPRESS Manuale utente
BraunAbility
BraunAbility KIT9 Manuale utente
BraunAbility
BraunAbility RQ10MH Manuale utente
BraunAbility
BraunAbility RBC Manuale utente
BraunAbility
BraunAbility I-SQE16MK Manuale utente
BraunAbility
BraunAbility T-RQ10PK Manuale utente
BraunAbility
BraunAbility HAL2 Manuale utente
