brel-motors MG-45 Manuale utente
Page 1
BREL motors is part of:
Manual Brel curtaintrack motor
Type MG-45
Read the manual before you begin the installation. If these instructions are not followed,
this may lead to defects and injury in which warranty can’t be claimed.
warning:
Children cannot recognize the dangers of electrical equipment and may therefore not work with it.
It is important to follow this instruction for your own safety.
1. Do not operate the motor in humid surroundings.
2. The motor must be installed correctly.
3. Keep the antenna in a good condition and do not shorten. The antennashould not come intocontact with other
metal parts otherwise it will reduce the effect.
4. The motor must be protected from direct moisture influences.
____________________________________________________________________________
Functions DC-415
Stop
|
Open A---------- -----------Close A
Open B---------- -----------Close B This is a 2-channel transmitter,
Channel*------------ two P2 keys for each one channel.
(* Change channel
works only with DC-416) P1 -------
P2 -------
Works with all BREL transmitters:
_____________________________________________________________________________
Technical data of the motor Type MG45
•Motor Voltage: 230V
•Power: 45 Watt
•Speed: 12 rpm
•Max. curtain weight: 40 kg
•Ampèrage 0.23 A
•Max. duration: 4 min.
•Moisture and dust: IP40
•Working temperature of the motor:
oNormal use: -10℃tot +40℃
oHeavy use: -20℃tot +70℃
Page 2
______________________________________________________________________________
Functions Reach
LED L1 = 100 meter L2 = 25 meter
P1 Programmbutton
Connection for switch
_______________________________________________________________________________
Wiring chart
_______________________________________________________________________________
Installation motor and rail
Attach the rail to the wall / ceiling.
Mount the rail not vertical.
If the motor don’t want to click easily, turn the gear wheel a bit and try again.
_______________________________________________________________________________
Step 1 Setting up the first channel
1x P1 2x P2 1x 5x LED of ➔
OR
Press 1x on the Press 2x on the Press the close button. The LED flashes 5x. Press the close or open button.
P1 button until the P2 button. Left or right determines the
LED flashes. direction of rotation.
Page 3
______________________________________________________________________________
Step 2 Setting with another direction of rotation
Variant A If the rotation direction is good, skip step 2 and continue with step 3.
1x P1 2x P2 1x ➔5x LED
You can now
continue with
setting the
end position.
Press P1 and hold Press 2x on the Press 1x open. LED flashes 5x.
until LED flashes. P2 button.
Variant B
1x P1
The direction of rotation has changed.
Press P1 and hold
until LED flashes.
_______________________________________________________________________________
Step 3 Setting the end positions
1x |1x ➔➔|
Press 1x close. Curtain closes completely. Press 1x open. Curtain opens completely.
Stops hard at the end. Stops hard at the end.
If the end positions are set with a hard stop, the curtain will stop 1 cm before the end in the future.
To remove / change the end position go to Option C.
______________________________________________________________________________
Step 4 Set or change preset position
If you press the Stop button longer than 3 sec., the motor will move to the preset position from any position.
1x P2 1x STOP 1x STOP
OK
Press 1x the P2 Press 1x stop button. Press 1x stop button. The position has now changed.
button. The LED flashes. The LED flashes.
In order to remove / change the preset position, the same procedure must be repeated at the position of the preset position.
Page 4
______________________________________________________________________________
Option A Delete transmitter
Deleting the transmitter can be done in three ways:
1. When setting up the first channel also the limit setup will be removed.
2.
Press P1 button until the LED flashes 3x and blinked 1x.
3.
1x P2 1x STOP 1x P2
OK
Press P2 button 1x. Press stop button. Press P2 button 1x.
_______________________________________________________________________________
Option B Teaching multiple transmitters (Maximum of 20 transmitters per receiver)
2x P2 1x P2
Press P2 button 2x Press P2 button 1x Programming the new
of the existing transmitter A. of the new transmitter transmitter is ready.
or channel B.
To delete one channel , you must repeat the above operation.
_______________________________________________________________________________
Optie C Eindposities verwijderen en nieuwe laten inleren.
1x P2 1x CLOSE 1x P2
OK
Press 1x P2. Press 1x close button. Press 1x P2. LED flashes 5x for confirmation.
Then let the curtain open and close. This person then looks for the new final positions himself.
Indice
Altri manuali brel-motors Motore
brel-motors
brel-motors MJE24S Manuale utente
brel-motors
brel-motors BTE 50 Manuale utente
brel-motors
brel-motors BJE24TD Manuale utente
brel-motors
brel-motors MGLE-45 Manuale utente
brel-motors
brel-motors MLE Series Manuale utente
brel-motors
brel-motors MJE24D Manuale utente
brel-motors
brel-motors BLE 25 Manuale utente
brel-motors
brel-motors BR35 Manuale utente
brel-motors
brel-motors MS55-60 Manuale utente
brel-motors
brel-motors BGLE-980 Manuale utente
brel-motors
brel-motors BJE24S Manuale utente
brel-motors
brel-motors BJE24DD Manuale utente
brel-motors
brel-motors MGS-45 Manuale utente
brel-motors
brel-motors MTE50-0.6 Manuale utente
brel-motors
brel-motors MR45-20 Manuale utente
brel-motors
brel-motors BTE50 Manuale utente
brel-motors
brel-motors BRE45 Manuale utente
