Brother GTXpro BULK DTF R2R Manuale utente

We share our experience to give you the best Support

1 / 26

08.2023/GTXproBulk_DTFR2R_Cookbook_v1.1/©BIMH, Germany

GTXpro BULK DTF R2R

COOKBOOK

CONTENT

1GENERAL INFORMATION 2

1.1 Software 2

1.2 Rule regarding the power supply 2

1.3 Environmental printing conditions 2

1.4 Storage of liquids 3

1.5 Control panel 3

2BEFORE PRINTING 4

2.1 Visual inspection 4

2.2 Alignment of the machines 5

2.3 Refill the powder at the PowDR 7

2.4 Daily nozzle test 7

3HOW TO PRINT 9

4DURING THE DAILY WORK 9

4.1 Inserting a film roll 9

4.2 Before white ink refill 13

4.3 Ink refill 14

4.4 Ink tank calibration 16

4.5 Cleaning solution refill 17

4.6The obstacle sensor 17

4.7 End of film sensor 18

4.8 Event of power failure 19

4.9 Cleaning and replacement of parts 19

5MAINTENANCES 20

5.1 Weekly maintenance 20

5.2 Monthly maintenance 23

5.3 Preventive maintenance 25

5.4 Extract a logfile for support 25

5.5 When not using the printer 25

6CONSUMABLES 26

2 / 26

08.2023/GTXproBulk_DTFR2R_Cookbook_v1.1/©BIMH, Germany

1 GENERAL INFORMATION

The printer should only be used by operators who are appropriately trained in its safe operation.

The printer is not suitable for use in places where children are present.

The GTXpro should always be left with power ON, also when it is not in use.

Power is needed to perform the recirculation of the white ink every day. This process does not consume ink.

If the GTXpro is turned OFF for a long time it might get damaged.

Only pull the plug in an emer-

gency or when requested by a

display message!

IMPORTANT RULE REGARDING THE POWER SUPPLY

1.2

ENVIRONMENTAL PRINTING CONDITIONS

1.3

SOFTWARE

1.1

Always make sure that you use the latest software for your GTXpro BULK DTF R2R.

You find the latest versions here:

https://base.brother.digital/driver-firmware/gtxpro-roll/

Mandatory temperature and air humidity for the best print result:

MAX

30°

MIN

18°

MAX

85%

MIN

35%

Required to keep your warranty for the printer!

Temperature & air humidity are recorded in the log file!

3 / 26

08.2023/GTXproBulk_DTFR2R_Cookbook_v1.1/©BIMH, Germany

If temperature is too cold: The printer will switch automatically to “Low-Temp Mode” and reduce the

speed. Raise the temperature of the printer‘s environment.

If temperature is too high: Please turn down the temperature of the surrounding area of the printer.

If humidity is too low: The printer will perform auto-cleaning after every print if the humidity is lower

than 35%.

Please install a humidifier in your workspace.

If humidity is too high: Please try to lower the humidity of the surrounding area of the printer.

Please always keep the temperature and humidity within the required ranges, otherwise the GTXpro

might get damaged.

Temperature/Humidity Info

Confirm network setting

Language

Version



Temperature/Humidity Info

Temperature [21°C ]

Humidity [55 % ]

Press OK to return



Please check the temperature and air humidity in the menu of the printer:

The liquids should be stored at a temperature between minimum 0°C and maximum 40°C.

MAX

40°

MIN

0°

Please turn over the white ink refill tank every week.

Do not use inks or liquids with a temperature below

18° C or above 30° C .

STORAGE OF THE LIQUIDS

1.4

EXPLANATION OF THE CONTROL PANEL

1.5

The display shows the current loaded print file with

the choosen print format, the approximate ink

consumption for it and the number of prints.

In the bottom left corner the ink level is shown.

The light blue rectangles show the selection of print

direction and the resolution of the print.

Warnings are displayed in yellow in the bottom right

corner. By pressing , the display changes to the

warning display on which the warning and the nee-

ded operations are indicated.

4 / 26

08.2023/GTXproBulk_DTFR2R_Cookbook_v1.1/©BIMH, Germany

A: Freely assignable speed dial button

B: Button for platen moving

C: Cancel button

D: Print start

MENU/OK: Opens the menu and confirms actions.

:Cursor buttons for moving through the menus.

E: The LEFT cursor button is the go back button.

F: Power switch ON/OFF

G: USB 3.0 Typ A port to load print files from an

USB-stick.

H: LAN port for connection to your PC.

J: USB Typ B port for connection to your PC.

Please follow all the instructions shown on the

display.

When you see an “Error/Warning” yellow

 numberpressthe″″keytoknowwhatyou

have to do to erase the Error/Warning.

Stand by

01 

Error/Warning

 2BEFOREPRINTING

VISUAL INSPECTION

2.1

Regularly check all moving parts of the machine and look for ink leaks.

Check the level in the waste ink tank and, if necessary, empty it.

5 / 26

08.2023/GTXproBulk_DTFR2R_Cookbook_v1.1/©BIMH, Germany

Check that the GTXpro Roll and the PowDR are still aligned (a laser is helpful).

The brakes of the castors should always be applied.

A: 23 cm parallel to the printer; B: 25-30 cm parallel to the printer

ALIGNMENT OF THE MACHINES AND THE FILM

2.2

The film can run skewed through the system for various reasons, even if the machines are precisely

aligned. Missalignment of the film leads to poor print results.

The missalignment can be checked on different positions on the runway of the film.

E F G H H

6 / 26

08.2023/GTXproBulk_DTFR2R_Cookbook_v1.1/©BIMH, Germany

Is the film roll centred and does the film have

equal tension at the edges?

Is the fixing lever closed?

Is the film just aligned with the roll?

Is the film aligned straight on the printing table?

Can the film slide freely through the guide

Does the film have the same tension at the edges?

The film does not touch any part of the powder

unit?

7 / 26

08.2023/GTXproBulk_DTFR2R_Cookbook_v1.1/©BIMH, Germany



Fill the powder tank with the necessary amount

of DTF powder.

REFILL THE POWDER AT THE PowDR

2.3

Is the film in the melting unit well aligned?

You have to perform a nozzle test for CMYK and white every morning before starting your production.

Head Cleaning

Test Print

Ink refill

Add cleaning solution

Print Data Load



Test Print

Nozzle Check CMYK

Nozzle Check White



Test Print

Nozzle Check CMYK

Press OK to Start





Printing...

14x16 inch

0.04 cc



001

1200 dpi





DAILY NOZZLE TEST

2.4

If a new powder type has been filled into the pow-

der unit or the unit has been moved, the powder

sensor must be recalibrated.

Consult the PowDR manual.

8 / 26

08.2023/GTXproBulk_DTFR2R_Cookbook_v1.1/©BIMH, Germany

Test Print

Nozzle Check White

Press OK to Start





Printing...

14x16 inch

0.07 cc



002

1200 dpi







When the nozzle checks are done, run the film

out of the back of the printer:

A: Press for transportation of the film.

B: Press the Menu/OK button.

C: Press Cancel when the print comes out of the

back of the printer.



Check the nozzle pattern by holding a white

(CMYK print) or black (White print) paper sheet

behind the film.

S/N: M9933069

Firm Ver 1.70.0001

Prints: 770

15/01/2023 10:11:02

This is what the nozzle checks should look like:This is what the nozzle checks should look like:

S/N: M9933069

Firm Ver 1.32.0002 Prints: 971

15/01/2022 10:41:07

9 / 26

08.2023/GTXproBulk_DTFR2R_Cookbook_v1.1/©BIMH, Germany

If not all nozzles are firing, start a cleaning of the affected print head to open the clogged nozzles.

Head Cleaning

Test Print

Ink refill

Add cleaning solution

Print Data Load



Head Cleaning

Normal Cleaning

Powerful Cleaning

Super Cleaning

Flash Firing



Powerful Cleaning

All Colors

All Whites

All Print Heads



Powerful Cleaning

All Colors

Press OK to Start



If still more than 10 nozzles are missing, select super cleaning.

Perform a nozzle test to check the result and perform another cleaning if the nozzles still do not spray.



Loosen both thumbscrews of the roll holder

on the front side and the screws of the plates.



Adjust the plates to the width of the roll. The

numbers under the outer screws are decisive.

3 HOW TO PRINT

4 DURING DAILY WORK

INSERTING A FILM ROLL

4.1

You can find instructions for printing here ( >TIP-Sheets > GTXpro Roll > Print Settings/Software Guide):

https://base.brother.digital/tip-sheets/

Please make sure that the resolution of your printfile is not too low.

A resolution of 300 dpi in relation to the print format is recommended.

10 / 26

08.2023/GTXproBulk_DTFR2R_Cookbook_v1.1/©BIMH, Germany



Insert the film roll between the jaws.

A: The rolling direction



Center the roll between the edges of the plates.

Then fasten the thumbscrews.



Turn the brake knob right side counter-clockwise

until it stops to release the brake completely.



Repeat the operation on the left side.



A: Insert the film carefully and in an even way.

B: The lock lever must be down to be open.



Align the film straight on the print table. If you

use a 40cm roll, remove the screws from the

side guides and screw them back into the

outer holes.



Then slightly, with one finger, turn each knob

clockwise till you feel a slight resistance.

It is best to set the buttons identically.



HELPFUL: Attach a spring balance to the film and

slowly unroll it a little. The resistance value should

not exceed 100 gr.

Indice

Altri manuali Brother Stampante

Brother

Brother HL-1470N Manuale utente

Brother

Brother HL-3400CN Series Manuale utente

Brother

Brother MFC-8460N Istruzioni per la costruzione

Brother

Brother HL-4150CDN Manuale utente

Brother

Brother DCP-155C Manuale utente

Brother

Brother TD-2020A Manuale utente

Brother

Brother HL-7050 Series Manuale utente

Brother

Brother DCP-B7500D Manuale utente

Brother

Brother Pocketjet PJ-623 Manuale utente

Brother

Brother MFC-L8900CDW Manuale utente

Brother

Brother HL-6050 Manuale utente

Brother

Brother HL-S7000DN Series Manuale utente

Brother

Brother HL-5380DN Manuale utente

Brother

Brother HL-1230 Manuale utente

Brother

Brother DCP-L2560DW Manuale operativo e di manutenzione

Brother

Brother QL-700 Manuale utente

Brother

Brother MFC-T920DW Manuale utente

Brother

Brother HL-53 Manuale utente

Brother

Brother HL-L8260CDW Manuale utente

Brother

Brother MFC-L2750DWXL Manuale utente

Brother

Brother HL-5580D Manuale utente

Brother

Brother 1470N - HL B/W Laser Printer Manuale utente

Brother

Brother MFC-L2771DW Manuale utente

Brother

Brother MFC-J2510 Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente