Brother BAS-416 Manuale utente
Page 1 of 3
An increased resistance that makes it either hard or impossible for the main motor to turn the
degree wheel or pulley causing a motor lock error. Listed below are some causes of the
problem. Listed in the order that they occur most.
Lack of Lubrication
• Oil the machine as specified under initial unpacking procedure. Make sure and oil the
rotary hook.
Thread tangled in rotary hook
• Open bobbin case cover and look for thread tangled in the rotary hook around it or
behind it and remove thread. Rotate pulley back to stop position after finished. This
can be caused by bird’s nest, which is created by various things. Such as
• Incorrect threading of machine
• Incorrect needle size or type of needle for application
• Needle being installed backwards
• Worn needles
• Incorrect backing for the application.
• Loose upper thread tension
• Inner rotary hook adjuster set incorrectly
Foreign object stuck in the rotary hook
To check if something is causing binding in the rotary hook see if you can
move the bobbin basket clockwise and counter-clockwise. The bobbin
basket is part of the rotary hook. This is part that the bobbin case fits into.
To check the play put two fingers on the bobbin case latch and rotate your
fingers in both directions. You should have a little play in both directions. If
not then there is something lodged in the raceway of the rotary hook. Clear
obstruction or replace rotary hook. This can be caused by
• Broken pieces of needle lodged somewhere in hook
• Thread badly entangled in rotary hook.
Rotary Hook
Check for broken bits of
needles in this area.
Motor Locks – Causes and Solutions
For Technical Assistance Please Call Toll Free 1-877-4BROTHER
Page 2 of 3
A buildup of thread is behind the moving knife
o Remove needle plate and remove the thread build up behind the moving and fixed
knife. This build up is causing the moving knife not to be able to complete its cycle
Needle hitting presser foot
o Adjust presser foot so that is aligned with the hole in the
needle plate.
o Replace bent presser foot and adjust presser foot height.
o Replace bent needle.
Needle hitting needle plate
o Adjust the alignment of the needle plate. Rotate pulley to
150 degrees and see if needle goes through the middle of the
hole in the needle plate. If not, loosen the two screws that
hold on the plate and move the plate to align with needle
and retighten screws. Turn pulley backwards to stop position
(100 degrees).
Needle hit the hoop while sewing
o Loosen the needle holding setscrew of the needle that is stuck in the hoop. Rotate the
pulley to bring the needle up. Remove hoop from machine and turn pulley back to
stop position (100 degrees). Remove needle from hoop with pliers.
Moving knife is not at proper position
o Remove needle plate and check position of
moving knife. If knife is out of position try
manually moving it back into position with
your fingers. Cycle the trimmer with the
button on the keypad and recheck
adjustment.
Motor Locks – Causes and Solutions
For Technical Assistance Please Call Toll Free 1-877-4BROTHER
Page 3 of 3
Moving knife is out of adjustment
o Before adjusting moving knife check the fixed
knife to see if it is 10mm from the needle and
against the pin. Usually if the fixed knife is
pushed all the way back against its adjustment
slot that is approximately 10mm. If needed
adjust clearance of moving knife to 1.2 mm.
You will need to remove the chrome are cover
to gain access to the adjustment bolts.
Inner rotary hook adjuster set incorrectly
• Check clearance of inner rotary hook stopper,
also known as the positioning finger. It may be in to
far causing thread to wrap around it.
Thread take up lever striking the needle case cover
o Adjust thread take up driving lever so that all take up levers are even. Make sure this
is done at stop position (100 degrees). You will need to remove the tension base to
gain access to the adjustment bolt.
Needle depth or 0 degree stopper out of position
o Adjust needle depth first and then 0 degree stopper. Please refer to your instruction
manual for adjustment.
Motor Locks – Causes and Solutions
For Technical Assistance Please Call Toll Free 1-877-4BROTHER
Altri manuali per BAS-416
9
Questo manuale è adatto per i seguenti modelli
18
Indice
Altri manuali Brother Macchina da cucire
Brother
Brother EF4-B561 Manuale utente
Brother
Brother 888-E31 Manuale utente
Brother
Brother DB2-B737 Mark III Manuale utente
Brother
Brother 885-V14 Manuale utente
Brother
Brother FD3-B256 Manuale utente
Brother
Brother ULT-2001 Manuale utente
Brother
Brother S-7220B Guida all'installazione
Brother
Brother Serger 1034D Manuale utente
Brother
Brother RH-9800 Manuale utente
Brother
Brother Entrepreneur Pro PR-1000 Manuale utente
Brother
Brother BAS-600 Manuale utente
Brother
Brother BES-1240BC Manuale utente
Brother
Brother PEDESIGN PLUS Manuale utente
Brother
Brother Innov-is 1500D Manuale utente
Brother
Brother Simplicity SB530T Manuale utente
Brother
Brother M945 Super ACE III Manuale utente
Brother
Brother S-7200A Istruzioni per il montaggio
Brother
Brother LT2-B872 MKII Manuale utente
Brother
Brother 882-W83 Manuale utente
Brother
Brother Innov-i-s 80 Manuale utente
