Bruker BEST Manuale utente

Version

BEST

Barcode Reader

Installation Manual

004

The information in this manual may be altered without notice.

BRUKER BIOSPIN accepts no responsibility for actions taken

as a result of use of this manual. BRUKER BIOSPIN accepts

no liability for any mistakes contained in the manual, leading to

coincidental damage, whether during installation or operation of

the instrument. Unauthorized reproduction of manual contents,

without written permission from the publishers, or translation

into another language, either in full or in part, is forbidden.

This manual was written by

Volker Reiß

Rheinstetten, Germany

P/N: Z31545

DWG-Nr.: 1252004

Installation Manual Version 004 iii

Contents

Contents .............................................................. iii

1 Introduction ............................................................ 5

1.1 General ............................................................................... 5

2 Adjusting the Z-Tower Height ................................ 7

2.1 General ............................................................................... 7

2.2 Hardware ............................................................................ 7

2.3 Software .............................................................................. 8

3 Mounting the Barcode Reader................................ 9

3.1 Mounting the Barcode Reader on the Gilson Liquid Handler . 9

3.2 Connecting the Power Supply ............................................ 12

3.3 Connecting the Serial Cable .............................................. 12

4 Software................................................................ 13

4.1 General ............................................................................. 13

4.2 Defining the Barcode Reader ............................................. 13

4.3 Programming the Barcode Reader ..................................... 15

5 Barcodes............................................................... 17

5.1 General ............................................................................. 17

5.2 Label Size ......................................................................... 17

5.3 General Barcode Information ............................................. 17

5.4 Matrix ID ........................................................................... 18

5.5 Matrix Type ....................................................................... 18

5.6 Barcode Positioning ........................................................... 20

5.7 Examples .......................................................................... 22

Figures ................................................................ 25

Tables .................................................................. 27

iv Installation Manual Version 004

Contents

Installation Manual Version 004 5 (29)

Introduction 1

General 1.1

This manual will guide you through the installation of the barcode reader for the

Gilson Liquid Handler.

The installation process consists of three steps:

1. Changing the height of the Gilson Z-tower.

2. Mounting the barcode reader on the Gilson Liquid Handler.

3. Defining the barcode reader in the software.

These steps will be explained in the upcoming chapters.

6 (29) Installation Manual Version 004

Introduction

Installation Manual Version 004 7 (29)

Adjusting the Z-

Tower Height 2

General 2.1

Before the barcode reader can be used with the Gilson Liquid Handler´s robot

arm, the working height of the Z-tower must be changed.

Hardware 2.2

The barcode reader set contains two black anodized (i.e. has a black eloxation

layer) adjustment cylinders (one with a height of 127 mm, one with a height of 175

mm), which aid you in mounting the Z-tower at the correct height. The 175 mm ad-

justment cylinder is used for the adjustment when cooling racks are used. In either

case the appropriate value must be set up in the Gilson Control Software.

Be sure that you have the correct adjustment cylinder (black anodized). The

original gray cylinder has a height of only 124 mm and this may cause prob-

lems when reading barcodes!

The first step in modifying the working height of the Z-tower is to turn the power off

and remove all the racks from the Gilson Liquid Handler´s bed. Move the robot

arms to the center of the bed as shown in "The Gilson Liquid Handler" on page

To achieve the 127 mm (or 175 mm when using a cooling rack) height, loosen the

screw on the back of the Z-tower and pull the Z-tower upwards slightly. Place the

black anodized adjustment cylinder between the bottom of the Z-tower and the

floor of the Liquid Handler´s bed. Lower the Z-tower until it sits on top of the ad-

justment cylinder. The scale should then show the value 127 mm (or 175 mm

when using a cooling rack). Tighten the screw and remove the black anodized

adjustment cylinder.

8 (29) Installation Manual Version 004

Adjusting the Z-Tower Height

Figure 2.1. The Gilson Liquid Handler

Software 2.3

The new height must also be entered in the Gilson Liquid Handler software. Refer

to the corresponding Gilson Liquid Handler manual to set up this value.

Z-Tower

XY-Robot Arm

Rack

Bed

Installation Manual Version 004 9 (29)

Mounting the

Barcode Reader 3

Mounting the Barcode Reader on the Gilson Liquid Handler 3.1

1. Mount the barcode reader on the barcode reader bracket using the 2 M3x8

hexagon screws, as shown below:

Figure 3.1. Mounting the Barcode Reader to the Bracket

2. Mount the barcode reader bracket on the Z-tower of the Gilson Liquid Handler

using the two M3x10 cylinder screws. Ensure that you mount the bracket just

under the top plate of the Z-tower cover. There should not be a gap between

the Z-tower cover and the bracket (as shown in Figure 3.2.).

2x M3x8

Hexagon

Screws

Barcode Reader Bracket

10 (29) Installation Manual Version 004

Mounting the Barcode Reader

Figure 3.2. Mounting the Barcode Reader Bracket

3. Affix the two adhesive fasteners to the Z-tower arm as shown in Figure 3.3.

and fasten the barcode reader cable to them using the two plastic strips.

The lower cable socket should be placed about 20 mm above the motor and

the upper socket about 20 mm below the upper end of the Z-tower.

Cylinder

Screws

No gap!

Side View

Indice

Altri manuali Bruker Lettore di codici a barre

Bruker

Bruker Gilson Manuale utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente