Buchi B-290 Guida utente

BÜCHI Mini Spray Dryer B-290

Quick Operation Guide

Switch

Aspirator on

Set Inlet temperature,

Switch Heater on

Open

compressed air

Distilled water ready,

start peristaltic pump

Reduce inlet

temp. and/or

increase

pump rate

Increase inlet

temp. and/or

reduce

pump rate

Adjust Nozzle

cleaning

Change from distilled

water to product

Change from product

to distilled water

Inlet Temp. reached

Spray Drying in process

Outlet Temp.

too high

Wet glass

product sticking

Generates the gas stream in the system. 100% re-

commended, so efﬁcient drying and best separation

is obtained.

For aqueous solutions, inlet temperatures are between

100 and 220°C. Lower range for heat sensitive product.

Typical set point 150°C.

By opening the needle valve on the ﬂow control, the

compressed air for the feed dispersion is set. Typical

level is 4 cm (approx. 600 l/h).

Close peristaltic pump bed. The process is started

with pure water to get the drying conditions . The outlet

temp. will decrease due to the consumption of energy

by the evaporation.

Typical set point of pump 30%.

The outlet temp. deﬁnes the maximal thermal load for

the product. Adjust inlet temp. and pump rate to obtain

a certain outlet temp. Lowering the aspirator rate will

also decrease the outlet temp.

In case of suspensions or product which tend to clog

the nozzle, the nozzle cleaning is switched on. Higher

number (2-9) means more cleaning pushes.

The spray drying starts as soon as the tube is switched

from pure water to product (by feed switch valve or

manually). The outlet temp. will slightly increase becau-

se less water has to be evaporated, eventually adjust

inlet temp.

Switch back to pure water to clean tube and nozzle.

Additional cleaning effect by drawing air bubbles.

BÜCHI Mini Spray Dryer B-290/

BÜCHI Inert Loop B-295

Quick Operation Guide

Switch instrument on,

switch aspirator on

Set cooling temperature

on Inert Loop B-295

Feed nitrogen be opening

spray ﬂow valve

Heater and feeding ready

to be started

Start with

pure solvent

Adjust Nozzle

cleaning

Change from pure

solvent to product

Change to

pure solvent

O2 level <6% is reached

Spray Drying in process

Temperatures constant

Solvent

recovery

Inert Loop starts to cool, both signal lamps are on (after

20 sec.). When starting the aspirator, pressure signal

lights off: gas stream is circulating. 100% recommen-

ded for efﬁcient drying and best separation in cyclone.

The set cooling temperature depends upon the solvent

used. For boiling point <70°, -20° is recommended, for

pure water, 10° must not be fallen below.

Nitrogen is fed into the cycle and the same volume is

leaving the system by the exhaust tube. The level of

oxygen is decreasing. If not, check tightness to ﬁnd

leakage.

The system is now under inert condi-tions; heater is

started. The procedure is equal as on the back side.

Inlet temp. approx. + 10°C above boiling point of sol-

vent.

Pure solvent is used to get the drying conditions. High-

er pump rates can be used, typical set point is 60%.

In case of suspensions or product which tend to clog

the nozzle, the nozzle cleaning is switched on. Higher

number (2-9) means more cleaning pushes.

The spray drying starts as soon as the tube is swit-

ched from solvent to product (by feed switch valve or

manually).

At the end of the process, switch back to pure solvent

to clean tube and nozzle. Additional cleaning effect by

air bubbles.

Empty receiving bottle in Inert Loop B-295.

www.buchi.comBÜCHI Labortechnik AG 96974 0904 300

Altri manuali per B-290

Altri manuali Buchi Attrezzature da laboratorio

Buchi

Buchi Lyovapor L-300 Manuale utente

Buchi

Buchi Pure C-810 Manuale utente

Buchi

Buchi HydrolEx H-506 Manuale utente

Buchi

Buchi ProxiMate Manuale utente

Buchi

Buchi Lyovapor L-300 Manuale utente

Buchi

Buchi Process Analyser X-One Manuale utente

Buchi

Buchi S-300 Manuale utente

Buchi

Buchi Rotavapor R-220 Manuale utente

Buchi

Buchi NIR-Online X-Sential Manuale utente

Buchi

Buchi FatExtractor E-500 Manuale utente

Buchi

Buchi Inert Loop S-395 Manuale utente

Buchi

Buchi Syncore Manuale utente

Buchi

Buchi Rotavapor R-3000 Manuale utente

Buchi

Buchi NIRMaster Manuale utente

Buchi

Buchi 535 Manuale utente

Buchi

Buchi S-300 Manuale utente

Buchi

Buchi FatExtractor E-500 Manuale utente

Buchi

Buchi B-820 Manuale utente

Buchi

Buchi KjelMaster K-375 Manuale utente

Buchi

Buchi Rotavapor R II Manuale utente

Buchi

Buchi Pure Chromatography C-900 Manuale utente

Buchi

Buchi V-300 Manuale utente

Buchi

Buchi Scrubber K-415 Manuale utente

Buchi

Buchi K-424 Manuale utente

Manuali Attrezzature da laboratorio popolari di altre marche

Qiagen

Qiagen DML 3000 Manuale utente

Queensgate

Queensgate NANOSCAN OP400 Manuale di programmazione

Conviron

Conviron GEN1000-GE Manuale utente

Parr Instrument

Parr Instrument 4560 Manuale di istruzioni

IKA

IKA IC control Manuale utente

Integra

Integra DOSE IT Manuale utente

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuale utente

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuale utente

NI PXI-5422 Manuale

Collomix

Collomix Aqix Manuale utente

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente

Ocean Insight

Ocean Insight FLAME-NIR+ Manuale utente

Parker

Parker ALIGN-MG-NA Manuale utente

BD 644787 Manuale utente

DENTAURUM

DENTAURUM Compact Megaplus Manuale utente

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuale utente

VWR

VWR SAS Super IAQ Manuale utente

illumina

illumina MiSeqDx Manuale utente