Burly B28-282 Manuale utente
Installation Instructions
REAR LOWERING KIT FOR
FXD/FXDWG MODELS 1991-1999
HARLEY-DAVIDSON
888-367-1871 714-367-1871 FAX: 714-523-3220 6900 Marlin Circle, La Palma, CA 90623
[email protected] http://www.burlybrand.com
Part#B28-282INS Page 1 of 2 Harley Davidson is a registered trademark of the Harley Davidson Motor Company Inc., Milwaukee, WI
nFor proper installation, the rear wheel and shock springs must be
removed. If you do not have access to a stand capable of safely
supporting/lifting the motorcycle so that the wheel can be removed, as
well as a tool capable of removing/replacing the shock spring, please
allow your dealer to assist you.
nDO NOT install on models other than FXD & FXDWG - Will not fit
FXD Convertibles w/ OEM saddlebags.
nThis kit is designed to work with Harley-Davidson OEM shocks (12.5”),
swingarm, frame, and OEM tire size. DO NOT USE WITH LOWERED
SHOCKS!!!
nThe operator must use extreme caution when operating a modified
motorcycle, particularly while familiarizing himself with its altered handling
characteristics.
nCheck your motorcycle for proper parking lean angle AFTER installation of
this kit. Your sidestand may require modification.
nFollow all instructions to achieve proper clearance.
nOwners of any model using a lowering kit with saddlebags (hard or soft)
must check for sufficient shock-to-bag clearance. Some models may
require modifications to the bag mounts when the lowering kit is installed.
nEnclosed sticker must be applied to a visible area of any motorcycle on
which the Burly Brand lowering kit has been installed in order to inform
potential riders that the bike has been modified.
We continually inspect and try to improve our products. All parts have been inspected prior to packaging, and our guarantee is limited to replacement of defective
parts. This guarantee is in lieu of all guarantees or warranties implied or expressed. Because we cannot control the application of our products, buyer assumes
risks for any and all damage caused by himself or third party, by virtue of failure of these parts. We make no warranty as to products distributed by us, expressed or
implied, including without limitation any warranties or merchant ability and fitness for a particular purpose. We will however, pass on all warranties made by the
manufacturer, who has sole responsibility for performing such warranties. The manufacturer shall solely be responsible for any damage to person or property
arising from design, manufacturing and testing of all products, and we accept no liability for such damages. We shall not be liable for indirect or consequential
damages.
WARNINGS & ALERTS
LIMITED GUARANTEE
PARTS INCLUDED
PART NUMBER
INSTALLATION INSTRUCTIONS
B28-282
REV. B
nRead all the instructions carefully before installing this kit on your
motorcycle. Use your Harley-Davidson manual as a reference while
installing this kit.
nSupport and lift the motorcycle securely so the rear wheel is just off
the ground and able to spin with light brake drag. The balance point is
between the engine and transmission.
nRemove rear exhaust muffler to gain access to axle/axle nut. Remove
drive belt guard. Remove rear wheel and slide brake caliper assembly
off swingarm.
nRemove shocks. Install 3/4” Travel Limiters following the guidelines
below. Refer to drawing as for assistance. (See page two*)
a) To remove shock springs, compress spring & remove spring retainer
that holds & locates spring on shock.
b) Twisting the snap ring slightly, slip the snap ring onto shock shaft
between shock body and rubber bumper.
c) Install travel limiter halves onto shock shaft. Using snap ring pliers,
install snap ring into groove of travel limiter.
d) Re-install shock springs.*
nInstall Lowering Kit Bracket to the right side of swingarm, through hole
in stock shock mount. Use 1/2”-20x1.25” long bolt (provided) from
backside of swingarm mount. secure with 1/2”-20 Nylock nut
(provided). Torque to 30 foot pounds. Repeat process on the left side
Lowering Kit Bracket.
nPlace 1/2”-20x3” bolt (provided) in right side Lowering Kit Bracket
hole (this bolt is for new shock position). Place 1/2”-20x2.5” bolt
(provided) in left side Lowering Kit Bracket hole (this bolt is for new
shock position).
nRemove the right side upper shock stud. Install the remaining ¼”
spacer (provided) and remount the stud. The right shock mount
requires this spacer for proper alignment.
nRe-install both modified shocks onto their new mounting positions
(stock Acorn nuts and washers are retained on lower mounts). Torque
top/bottom nuts/bolts to 25 foot pounds.
nRe-install rear wheel & brake caliper assembly. Refer to Harley
manual for proper belt alignment and axle/nut torque.
nInstall belt guard, being sure to check for proper clearance at fender
to belt guard. Trim belt guard if necessary.
Continued on page 2
Installation Instructions
REAR LOWERING KIT FOR
FXD/FXDWG MODELS 1991-1999
HARLEY-DAVIDSON
888-367-1871 714-367-1871 FAX: 714-523-3220 6900 Marlin Circle, La Palma, CA 90623
[email protected] http://www.burlybrand.com
Part#B28-282INS Page 2 of 2 Harley Davidson is a registered trademark of the Harley Davidson Motor Company Inc., Milwaukee, WI
INSTALLATION INSTRUCTIONS
(Continued from page 1)
REV. B
Warning !!!
This kit is designed for use with the stock size tire and stock length (12.5”) shocks. Fender to tire clearance will be reduced if a larger tire
or shorter shock is used.
* While the springs are removed from the shocks, it’s a good idea to check the tire to fender clearance, brake caliper to fender clearance,
belt guard to fender clearance by temporarily installing the springless shocks (with travel limiter installed) onto the bike and swing the rear
wheel through it’s full range of motion. Be sure to take into consideration bumper compression and chassis flex (yes, it does flex).
Bumper
Indice
Altri manuali Burly Accessori per motociclette
