BWI Eagle AIR-EAGLE SR PLUS 36-HH-9 Manuale utente

AIR-EAGLE SR PLUS

36-HH-9

2.4 GHz RF Transmitter

Document Date: 6/21/2021

Product Rev: 12

36-HH-9

WARRANTY STATEMENT

BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and installed, will be free

from defects in material and workmanship for a period of 1 year after date of purchase. Said warranty to

include the repair or replacement of defective equipment. This warranty does not cover damage due to

external causes, including accident, problems with electrical power, usage not in accordance with product

instructions, misuse, neglect, alteration, repair, improper installation, or improper testing. This limited

warranty, and any implied warranties that may exist under state law, apply only to the original purchaser of

the equipment, and last only for as long as such purchaser continues to own the equipment. This warranty

replaces all other warranties, express or implied including, but not limited to, the implied warranties or

merchantability and fitness for a particular purpose. BWI Eagle makes no express warranties beyond

those stated here. BWI disclaims without limitation, implied warranties of merchantability and fitness for a

particular purpose. Some jurisdictions do not allow the exclusion of implied warranties so this limitation

may not apply to you. To obtain warranty service, contact BWI Eagle for a return material authorization.

When returning equipment to BWI Eagle, the customer assumes the risk of damage or loss during

shipping and is responsible for the shipping costs incurred.

SIGNAL RANGE

Max range statements are estimates based on a clear line of sight with few interferences. Actual range will

vary based on transmitting power, orientation of transmitter and receiver, height of transmitting and

receiving antennas, weather conditions, electronic interference, terrain, and physical obstacles, including

but not limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills, mountains).

WIRELESS STOP SYSTEMS WORK IN CONJUCTION WITH

HARD-WIRED SYSTEMS.

Wireless Stop and E-Stop devices must work in conjunction with a hard-wired

system. A wireless system should never be considered a primary life-saving device.

At least one hard-wired switch must be available in the event the wireless signal is

lost. Failure to comply may result in serious injury or death to personnel and

damage to equipment.

36-HH-9

Dimensions –4.71” L x 2.99” W x 1.12” D

(note: belt clip adds .43” to depth)

INTRODUCTION

The Air-Eagle SR PLUS TX is a handheld R.F. transmitter capable of sending up to sixteen unique digital

commands to an Air-Eagle SR Receiver located up to 600 feet away. Any number of transmitters and

receivers can be combined to create a medium-range radio frequency system that operates hazardous or

hard-to-reach equipment from safe, convenient locations. Eight user-programmable frequencies allow

multiple systems to operate simultaneously in the same area without interference. This transmitter will

automatically go into “sleep” mode when no buttons are being depressed on the unit to dramatically

extend battery life.

INITIAL OPERATION SET-UP

This transmitter comes factory set to frequency 1 and power level 4 (max range of 600 feet). If you wish to

change the default settings, follow the instructions for FREQUENCY PROGRAMMING AND POWER

LEVEL PROGRAMMING.

36-HH-9

CONTROLS & INDICATORS

TX LED

LED illuminates “RED” continuously while button is depressed, and unit is

transmitting. When this LED blinks briefly following a transmission, the

battery needs to be replaced. See Note #1

Note #1 –The low battery notification signals have been improved to provide more noticeable

indications and to safely disable communications BEFORE a low battery condition can corrupt internal

memory causing device failure. When a low battery is first detected, the TX LED will blink several times

after all buttons are released. If it is possible to replace the batteries now, please do so. If not, the

operator has approximately 15 more button activations. During this time, when a button is depressed

and held, the TX LED will blink SLOWLY. The slow blinking will continue several more times after all

buttons are released. Transmissions are still being sent to the receiver during this time. When a button

is depressed and the TX LED is RAPIDLY blinking, the RF output is disabled, and NO signal will reach

the receiver. The batteries MUST NOW BE REPLACED to resume normal functions.

Pushbuttons 1 thru 8

Transmit channel 1 thru 8 commands to the receiver

Pushbutton P/Shift

The P/Shift button performs two functions:

1. If button is depressed momentarily and another button is then pressed

within 10 seconds, the higher code for that button is transmitted. This

allows for transmission of pushbutton codes 9 thru 16.

2. If button is depressed for longer than 5 seconds, the transmitter will

enter “programming” mode. See PROGRAMMING section.

Pushbuttons 9 thru 16

Transmit channel 9 thru 16 commands to the receiver

GENERAL OPERATION

This transmitter sends up to 16 independent commands. Each button sends an RF Code for that channel.

Button 1 transmits channel 1 commands, button 2 transmits channel 2 commands etc. To send

commands 9 thru 16, the P/Shift button must be used. As noted under CONTROLS & INDICATORS, the

P/Shift button serves two purposes. As the “P” button, it allows you to program the transmitter to operate

on a different frequency. As the “Shift” button, it allows you to send commands 9 thru 16 to the receiver.

To use as the “P” button, you must press and hold the button for approximately 5 seconds to enter

programming mode. (See PROGRAMMING section for more details).

To use as the “Shift” button, press the P/Shift button momentarily. The TX LED will begin to flash rapidly

indicating you’re in the Shift mode. While in shift mode pressing buttons 1 thru 8 transmit the higher

numbered code for that button. The transmitter will stay in the Shift mode as long as buttons are being

depressed within 10 seconds of one another. During this time, the TX LED gives visual confirmation that

you’re in Shift mode by continuously flashing GREEN/RED rapidly. After 10 seconds has elapsed with no

buttons depressed, the transmitter will revert back to standard mode and the TX LED will extinguish. If,

while in Shift mode, you wish to transmit a button 1 thru 8 command and don’t want to wait for the Shift

mode to time out, you can simply press the P/Shift button momentarily to revert back to the standard

mode.

36-HH-9

FREQUENCY PROGRAMMING

Please read through these instructions completely before beginning programming procedure!

At any time, you can check the current frequency setting by depressing the P/Shift button, for

approximately 5 seconds, until the TX LED is illuminated RED. Then release the P/Shift button and watch

as the TX LED stays RED for about 10 seconds, goes out, then begins to blink. The TX LED will blink

RED one, two, three or four times for Frequencies 1 thru 4, or will blink GREEN one, two, three or four

times for Frequencies 5 thru 8 accordingly. See table below for clarification.

LED Flashes:

Indicates Unit is Operating On:

RED –one time

Frequency 1

RED –two times

Frequency 2

RED –three times

Frequency 3

RED –four times

Frequency 4

GREEN –one time

Frequency 5

GREEN –two times

Frequency 6

GREEN –three times

Frequency 7

GREEN –four times

Frequency 8

To change the setting, follow these steps:

To select from Frequencies 1 thru 8:

1. Depress the P/Shift button until the TX LED is illuminated RED. (Approximately 5 seconds)

2. Release the P/Shift button, then while the TX LED is still illuminated RED, depress Button 1 to

select “Frequency 1” or Button 2 to select “Frequency 2” etc. If the transmit LED goes out before

you have selected a network, no settings will have changed, andthe LED will blink corresponding

to the frequency that the TX is currently set to. You must then begin again at step 1 if you wish to

change the current setting.

3. The TX LED will blink to confirm that your frequency selection has been accepted, and then will

go out. For instance, if you have selected Frequency 1, the TX LED will blink RED once to

confirm. If you have selected Frequency 6, the TX LED blinks GREEN two times to confirm.

Programming is now complete, and the transmitter is active for normal operation.

You may repeat the above procedure if you wish to change the frequency at any time.

36-HH-9

POWER LEVEL PROGRAMMING

Please read through these instructions completely before beginning programming procedure!

All transmitters are set to Power Level 4 (max range 600 ft) default. The power level can be changed at

any time by following the procedure below. Power level settings will not be changed during normal battery

replacement.

At any time, you can check the current power level by depressing the P/Shift Button, for approximately 8

seconds, until the TX LED starts BLINKING GREEN. Then release the buttons and watch as the TX

continues to blink for 10 seconds, goes out, then begins to blink again. The TX LED will blink GREEN

one, two, three or four times corresponding the power level setting (see table below)

LED Flashes:

Indicates Unit is Set To:

GREEN –one time

Power Level 1 –Approx 100 Ft Range

GREEN –two times

Power Level 2 –Approx 250 Ft Range

GREEN –three times

Power Level 3 –Approx 400 Ft Range

GREEN –four times

Power Level 4 –Approx 600 Ft Range

To change the setting, follow these steps:

To select a power level:

1. Depress the P/Shift Button until the TX LED is BLINKING GREEN (Approximately 8 seconds)

2. Release the P/Shift Button, then while the TX LED is still blinking GREEN, depress Button 1 to

select “Power Level 1” or Button 2 to select “Power Level 2” etc. If the transmit LED goes out

before you have selected a power level, no settings will have changed, and the LED will blink

corresponding to the power level the TX is currently set to. You must then begin again at step 1 if

you wish to change the current setting.

3. The TX LED will blink to confirm that your power level selection has been accepted, and then will

go out. For instance, if you have selected Power Level 1, the TX LED will blink GREEN once to

confirm. If you have selected Power Level 3, the TX LED blinks GREEN three times to confirm.

You may repeat the above procedure anytime you wish to change the power level of the transmitter.

APPROVALS

United States (FCC)

MCQ-XBEE3

Canada (IC)

1846A-XBEE3

Europe (CE)

ETSI

Australia

RCM

Brazil

ANATEL 06329-18-01209

36-HH-9

SPECIFICATIONS

Keypad

Durable Sealed Membrane Keypad –Eliminates Dust, Dirt and

Moisture Failures

Enclosure

ABS UL94 HB

Enclosure with ring is rated IP54 *Not

Waterproof

Protective Ring

SEBS (TPE)

Power Requirements

3.0 VDC

Battery Type

(2) 1.5V lithium each, size AA, to equal 3.0VDC nominal. ***For

best performance use ONLY Energizer Brand Lithium Batteries

*Note: Current frequency settings are maintained in flash memory during battery

replacement. No reprogramming of frequency settings is necessary!

Battery Life(Active Usage)

Up to 6 months

Battery Life(Sleep Mode)

Up to 1 Year

Transmit Frequency

2.4GHz Spread Spectrum

RF Networks

Eight Independent Frequencies

RF Output Power

User Selectable from 1mW - 60 mW

Max Transmit Range

User-Selectable from 100 - 600 Feet

Note: Range figures are estimates, based on free-air terrain with limited sources of interference. Actual range will vary

based on transmitting power, orientation of transmitter and receiver, height of transmitting antenna, height of receiving

antenna, weather conditions, interference sources in the area, and terrain between receiver and transmitter, including, but

not limited to, indoor and outdoor structures such as walls, metal objects, trees, buildings, hills, and mountains.

Operating Temperature

-40oF to +185oF

Weight

Approx .23 lbs. (w/belt clip)

Indice

Altri manuali BWI Eagle Trasmettitore

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuale

BWI Eagle

BWI Eagle AIR-EAGLE SR 38-1400-DC Manuale

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-1400-4B-DC Manuale

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuale

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-1400-120VAC Manuale

BWI Eagle

BWI Eagle AIR-EAGLE XLT PLUS 461-HH-1 Manuale

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS Manuale

BWI Eagle

BWI Eagle AIR-EAGLE XLT 441-HH-2-VBR Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuale

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuale

BWI Eagle

BWI Eagle AIR-EAGLE XLT 441-HH-9-VBR Manuale

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-HH-1 Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000N4W-120VAC Manuale

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS Manuale

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000-BAT Manuale

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-1800-120VAC Manuale

BWI Eagle

BWI Eagle AIR-EAGLE XLT PLUS 465UEBD-HH Manuale

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS Manuale utente

BWI Eagle

BWI Eagle 461-1200-DC Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1150-120VAC Manuale

BWI Eagle

BWI Eagle 461-1400-AC Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1100R1-DC Manuale

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000-DC Manuale

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente