C.A. Technologies JAGUAR SLP Manuale utente



 







 



      





 !"#$%##&&'(&

  

  

  

  

  

  

  

  

  

 !"!#$%&'(!#

!$!)#**!#)"##)#)"+!#$)!

 

Jaguar SLP

GRAVITY FEED SPRAY GUN

PRODUCT INFORMATION

Coating Atomization Technologies P.O. Box 17820, Boulder CO 80 08 (888) 820-4498 Fax ( 0 ) 4 8-5708

www.sprayCAT.com

Operation and Maintenance Instructions for Jaguar SLP Gravity Spray Guns

Operation

1. Connect air supp y hose at hand e of gun. 5/16 air hose x 25 ft. max. ength is recommended. A so,

on y use CAT high f ow quick disconnects and avoid using any restrictive fittings for the air supp y to

the gun.

2. Screw the paint cup onto the guns gravity feed f uid in et.

3. F uid f ow can be contro ed using the f uid contro knob, this restricts f ow by imiting need e trave . It

is best to contro f uid f ow by the proper se ection of orifice size and use the f uid contro knob to

fine tune f ow rate.

4. Fan width can be adjusted using the fan contro knob. Turning the knob c ockwise narrows the fan.

Maintenance

IMPORTANT! Routine c eaning and maintenance is essentia to insure proper gun operation.

Severa states prohibit spraying so vent into the atmosphere and require the use of covered gun c eaner.

1. If a gun c eaner is being used, connect and c ean the gun in the gun c eaner according to the

manufactures instructions.

2. If a gun c eaner is not being used:

Remove air cap and c ean separate y using c ean so vent.

C ean the gravity feed cup thorough y, then spray c ean so vent through the gun unti c ean.

NOTE: Gun disassembly is not recommended for normal cleaning and maintenance.

Gun disassembly and reassembly instructions:

Have repair kit # 10-105 avai ab e before gun disassemb y.

Disassembly

To remove nozz e carrier (4) and air cap adapter (6):

1. Remove the air cap (1), f uid tip (2), f uid nozz e body (3) and need e (16).

2. Remove need e sea cartridge (17).

3. Loosen ocknut (11) and remove f uid in et (12).

4. The f uid nozz e carrier (4) and air cap adapter (6) wi now s ide foward from the gun hand e (13).

Reassembly

1. Insta new o-rings (8) and (7) on the air cap adapter (6).

2. Insta air cap adapter (6) into gun body (13).

3. Insta the ocknut (11) and sea (10) onto the f uid in et (12) as far as possib e.

4. Insta a new f uid in et sea (9) into the recessed area on the nozz e carrier (4) in et port.

5. Insta sea (5) onto nozz e carrier, then s ide the nozz e carrier (4) into the air cap adapter (6) as far as

possib e. Be sure the nozz e carrier extends into the ho e at the back of the gun head. Insta the need e

sea cartridge (17) but do not tighten.

6. Rotate the nozz e carrier (4) unti the f uid in et port in the nozz e carrier is a igned with the threaded ho e

in the gun body (13). Whi e in this position, insert the f uid in et (12) and tighten firm y.

7. Tighten need e sea (17) to approx.12 ft- bs torque.

8. Tighten f uid in et (12) to approx. 25 ft- bs torque.

9. Tighten ocknut (11) to approx. 33 ft- bs torque.

IT EM NO. PART NO. DESCRIPT ION IT EM NO. PART NO. DESCRIPT ION

1 See Air Cap Chart Air Cap 18 60-1033 Trigger Pivot Screw s

2 See Air Cap Chart Fluid Tip 19 60-2101 Trigger

3 33-1202 Fluid Nozzle Body 20 60-1520 Air Valve Assembly

4 60-J31H Nozzle Carrier 21 60-302 Air Valve Poppet

5 60-123 Seal 22 60-125 Seal*

6 60-34H Air Cap Adapter 23 61-1003 Air Valve Spring*

7 98-8026 O-Ring* 24 60-119 Seal*

8 60-131 O-Ring* 25 60-201 Rear Bushing

9 60-130 Seal* 26 60-204 Needle Return Spring*

10 60-124 Fluid Inlet Seal* 27 60-205 Spring Seat*

11 60-118 Locknut 28 60-202 Fluid Control Knob

12 60-127 Fluid Inlet 29 60-1510 Inlet Air Control (Optional)

13 60-1119 Gun body 30 60-122 Plug

14 98-0109 Allen Plug 31 60-104 Air Inlet Fitting

15 60-1504 Fan Control Assembly 32 - Gravity Cup (See Page 4)

16 See Air Cap Chart Fluid Needle 33 - Gravity Cup Lid (See Page 4)

17 60-1400 Needle Seal Cartridge*

*Indicates part included in repari kit # 10-105

23-1322-G

23-1310-G

23-1312-G

HVLP AIR CAP TEST GAUGES

FOR

JSLP

GUNS

23-1308-G

23-1313-G

23-1314-G

23-1315-G

23-1317-G

23-1319-G

MATERIAL TYPE MAXIMUM

PATTERN WIDTH CFM

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

HVLP KITS ORIFICE AIR CAP ORIFICE (TIP) NEEDLE

JK1308 0.8 23-1308 33-0208 40-1308

JK1310 1.0 23-1310 33-0210 40-1310

JK1312 1.2 23-1312 33-0212 40-1312

JK1313 1.3 23-1313 33-0213 40-1313

JK1314 1.4 23-1314 33-0214 40-1314

JK1315 1.5 23-1315 33-0215 40-1315

JK1317 1.7 23-1317 33-0217 40-1317

JK1319 1.9 23-1319 33-0219 40-1319

JK1322 2.2 23-1322 33-0222 40-1322

29 psi @ 13.5 cfm

FLUID NOZZLE / AIR CAP SELECTION CHARTS





SLP - Gravity Feed Spray Guns

12" 29 psi @ 13.5 cfm

12"

KITS FOR 



SLP GUNS

FLUID ORIFICE x

AIR CAP

0.8 mm x 1308

1.0 mm x 1310

1.2 mm x 1312

1.3 mm x 1313

1.4 mm x 1314

1.5 mm x 1315

1.7 mm x 1317

1.9 mm x 1319

2.2 mm x 1322

29 psi @ 13.5 cfm

12" 29 psi @ 13.5 cfm

12"

Revised 8/30/12

CP-JSLP Includes:

51-401 750cc A uminum Gravity Cup

51-418 Gravity Cup Lid

52-300 Mini Regu ator

98-0104 3/8 Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun C eaning Brush

51-430 Gravity Gun Hook

Air Caps and Need es shown on Page 1

CAT PACKS ALSO AVAILABLE WITH 3M PPS

Altri manuali C.A. Technologies Spruzzatore di vernice

C.A. Technologies

C.A. Technologies AutoCAT 100C Manuale utente

C.A. Technologies

C.A. Technologies Cougar Manuale utente

C.A. Technologies

C.A. Technologies TOMCAT 100C Guida alla risoluzione dei problemi

C.A. Technologies

C.A. Technologies Lynx 100C Manuale utente

C.A. Technologies

C.A. Technologies Techline JR Manuale utente

C.A. Technologies

C.A. Technologies Lynx L200C Manuale utente

C.A. Technologies

C.A. Technologies Lynx 300H Manuale utente

C.A. Technologies

C.A. Technologies Jaguar 300 Series Manuale utente

C.A. Technologies

C.A. Technologies LYNX L100CM Manuale

C.A. Technologies

C.A. Technologies CAT SLP Series Manuale utente

C.A. Technologies

C.A. Technologies AutoCAT 100CVT Manuale utente

C.A. Technologies

C.A. Technologies Lynx 100CVT Manuale utente

C.A. Technologies

C.A. Technologies CPR-FE Manuale utente

C.A. Technologies

C.A. Technologies Jaguar SLP Manuale utente

C.A. Technologies

C.A. Technologies Lynx 100CM Manuale utente

C.A. Technologies

C.A. Technologies Lynx 100H Manuale utente

C.A. Technologies

C.A. Technologies Lynx 100 Series Manuale utente

C.A. Technologies

C.A. Technologies FE-Line Fine Finish Manuale utente

C.A. Technologies

C.A. Technologies Panther 100G Manuale utente

C.A. Technologies

C.A. Technologies CPR Manuale utente

C.A. Technologies

C.A. Technologies Lynx 200C Manuale utente

C.A. Technologies

C.A. Technologies CAT-Xpress Guida alla risoluzione dei problemi

C.A. Technologies

C.A. Technologies H2O-CPR Manuale utente

C.A. Technologies

C.A. Technologies Jaguar 300H Manuale utente

Manuali Spruzzatore di vernice popolari di altre marche

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manuale utente

Graco

Graco 246737 Manuale per l'uso e la cura

Binks

Binks SV100 Manuale utente

Fimco

Fimco LG-4-3-1 Manuale utente

AG SPRAY

AG SPRAY FS-ATV-25BL Manuale utente

Nordson

Nordson MicroMax 2 Manuale utente

Bonide

Bonide 051 Manuale operativo

zogics

zogics Z-DAS Manuale utente

KISANKRAFT

KISANKRAFT KK-KBS-165 Manuale utente

Matrix

Matrix SG 650 Manuale utente

Anest Iwata

Anest Iwata SGA-3 Guida rapida

paasche

paasche VV Scheda tecnica

Carlisle

Carlisle DeVilbiss JGA-510 Manuale utente

Gardena

Gardena 11120 Manuale utente

Conrad

Conrad Hobby Airbrush K3 Manuale utente

wiwa

wiwa 14025 R/F Manuale utente

Graco

Graco EM 390 Manuale operativo

DeVilbiss

DeVilbiss LUNA2i Manuale utente