Cable-Tronix CT-CATTX Manuale utente
INSTALLATION MANUAL
CT-CATTX and CT-CATRX
CAT 5 Distribution Hub and Receiver
1
2
PACKAGE CONTENTS
This package contains:
One CT-CATTX Cat 5 Distribution Hub (transmitter)
One CT-CATRX Cat 5 Receiver
One 9 VAC Power Adaptor
One CT-CATTX/CT-CATRX Installation Manual
PRODUCT DESCRIPTION
The CT-CATTX/CT-CATRX is a CAT 5 distribution hub (transmitter) and receiver designed to
distribute high definition video and audio signals from one source to multiple locations over
extended distances using economical CAT 5 cable. The CT-CATTX has one set of RCA inputs and
one set of RCA loop-thru connectors to go to the next transmitter if installed. The CT-CATRX
supports one monitor with component video, right and left audio, and digital audio.The receiverhas
adjustable equalizer to correct for the signal loss caused by long cables.
SPECIFICATIONS
CT-CATTX / CT-CATRX
CAT 5 Distribution Hub and Receiver Specifications (Typical)
Video
1. Video Impedance 75 ohms
2. Video Bandwidth >75MHz (HD requires 37MHz minimum)
3. Video Gain 2V unterminated, 1V into 75 ohms
4. Nominal Input Level 1V peak-to-peak
5. Isolation Port to Port >65dB
6. Out to In Isolation >80dB
7. Return Loss >30dB
8. Distance 300 feet@1080i (500 feet with Cat 6 cable)
Audio (Analog)
9. Audio Input Impedance 22K ohm
10. Audio Output Impedance 1K ohm
11. Gain Unity
12. Frequency Response 20Hz to 20kHz
13. Signal to Noise 80dB@1V (out)
14. Nominal Input Level 1V peak-to-peak
15. Digital Audio Supports standard SPDIF digital audio. Not compatible with
analog input signals.
General
16. Power 9V AC@600mA with a 2.1mm center coaxial connector
17. Dimensions 174mm(W) x 25mm(H) x 83mm(D)
INSTALLATION
1. UNPACKING and HANDLING
Each unit is shipped assembled and factory tested. Ensure that all accessories are removed
from the container before discarding packing material
2. MECHANICAL INSPECTION
Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is
clean, and no connectors are broken, damaged, or loose. If equipment appears to be damaged
or defective please contact your distributor or Cabletronix at 1-610-429-1511 for assistance.
3. PRODUCT DIAGRAM
4. HARDWARE CONNECTIONS
a. Connect Cat 5 cables A1 and B1 to the CT-CATTX’s RJ-45 jacks. At the other end of
the same cables connect A1 and B1 to the CT-CATRX. The RCA outputs are used ot
connect to the remote monitor.
b. Insert the power supply connector into the power jacks of both units. Plug the wall
transformer into a power outlet. The power LED should be on and the unit is ready to
use. The CT-CATRX will have 3 LEDs on to indicate continuity of the CAT 5 cable. If
one of the Continuity LEDs is not on there could be a problem with the Acable. Both A
and B cables should be installed for the detector to work properly.
3
4
c. Adjust the equalization control to the approximate length of the CAT 5 cable. View the
picture on the monitor and fine tune the equalization control for the most pleasing
picture.
Troubleshooting assistance can be found on-line at www.cabletronix.com in addition to
support from Cabletronix sales engineers at 1-610-429-1511.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Cable-Tronix Ricevitore
