Cabletron Systems Spectrum EMM-E6 Manuale utente

EMM-E6

ETHERNET BRIDGE/

MANAGEMENT MODULE

INSTALLATION GUIDE

DCBA

ICH1Book Page 1 Tuesday, August 6, 1996 3:06 PM

ICH1Book Page 2 Tuesday, August 6, 1996 3:06 PM

EMM-E6 Installation Guide i

NOTICE

Cabletron Systems reserves the right to make changes in speciﬁcations and other information

contained in this document without prior notice. The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FORANY INCIDENTAL,

INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT

NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR

THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN

ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH

DAMAGES.



Printed in the United States of America

Order Number: 9031926 August 1996

SPECTRUM

LANVIEW

MMAC

, and

BRIM

are registered trademarks and

Element Manager

EMM-E6

APIM

CRBRIM

FPIM

EPIM

EPIM-A

EPIM-C

EPIM-F1

EPIM-F2

EPIM-F3

EPIM-T

, and

EPIM-X

are trademarks of Cabletron Systems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of

their respective companies.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment.

This equipment uses, generates, and can radiate radio frequency energy and if not installed in

accordance with the operator’s manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference in which case the user

will be required to correct the interference at his own expense.

WARNING:

Changes or modifications made to this device which are not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

Printed on Recycled Paper

ICH1Book Page i Tuesday, August 6, 1996 3:06 PM

Notice

ii EMM-E6 Installation Guide

DOC NOTICE

This digital apparatus does not exceed the ClassA limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

VCCI NOTICE

This equipment is in the 1st Class Category (information equipment to be used in commercial and/or

industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference

by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial

and/or industrial areas.

Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be

caused to radios and TV receivers, etc.

Read the instructions for correct handling.

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT

IMPORTANT:

Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)

that sets forth your rights and obligations with respect to the Cabletron software program (the

“Program”) contained in this package. The Program may be contained in ﬁrmware, chips or other

media. BY UTILIZING THE ENCLOSED PRODUCT,YOU ARE AGREEING TO BECOME

BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND

THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IFYOU DO NOT

AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED

PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.

ICH1Book Page ii Tuesday, August 6, 1996 3:06 PM

Notice

EMM-E6 Installation Guide iii

CABLETRON SOFTWARE PROGRAM LICENSE

1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this

package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the

2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the

Program.

3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws

and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and

venue of the New Hampshire courts.

EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY

1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in

writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including

its documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO

YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING

BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE

ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL

CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER

(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,

PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL,

INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)

ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,

EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR

ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME

INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO

YOU.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer

software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the

Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects

is proprietary data belonging to Cabletron and/or its suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as deﬁned in the

DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its

successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in

subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at

252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.

ICH1Book Page iii Tuesday, August 6, 1996 3:06 PM

Notice

iv EMM-E6 Installation Guide

DECLARATION OF CONFORMITY

Application of Council Directive(s):

89/336/EEC

73/23/EEC

Manufacturer’s Name:

Cabletron Systems, Inc.

Manufacturer’s Address:

35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name:

Mr. J. Solari

European Representative Address:

Cabletron Systems Limited

Nexus House, Newbury Business Park

London Road, Newbury

Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards:

EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment:

Networking Equipment, for use in a

Commercial or Light

Industrial

Environment.

We the undersigned, hereby declare that the equipment packaged with this notice conforms to

the above directives.

Manufacturer Legal Representative in Europe

Mr. Richard Michaud Mr. J. Solari

___________________________________ ___________________________________

Full Name Full Name

Manager of Engineering Services Managing Director - E.M.E.A.

___________________________________ ___________________________________

Title Title

Rochester, NH, USA Newbury, Berkshire, England

___________________________________ ___________________________________

Location Location

ICH1Book Page iv Tuesday, August 6, 1996 3:06 PM

EMM-E6 Installation Guide v

CONTENTS

CHAPTER 1 INTRODUCTION

1.1 EMM-E6 Overview.......................................................................1-1

1.2 How to Use This Manual .............................................................1-1

1.3 Document Conventions...............................................................1-3

1.4 Related Documents.....................................................................1-4

1.5 Getting Help.................................................................................1-4

CHAPTER 2 CONTROLS AND INDICATORS

2.1 The Faceplate..............................................................................2-1

2.2 Internal Components...................................................................2-2

2.3 LANVIEW LED

...................................................................2-6

CHAPTER 3 INSTALLATION

3.1 Unpacking the EMM-E6...............................................................3-1

3.2 Setting Mode Switches................................................................3-3

3.3 Pre-Installation Test.....................................................................3-5

3.4 Installation ...................................................................................3-7

3.5 Connecting to the Network........................................................3-10

3.5.1 Connecting a 10BASE-T Segment to an EPIM-T.........3-10

3.5.2 Connecting a 10BASE-F Segment to an EPIM-F2

or EPIM-F3 ...................................................................3-13

3.5.3 Connecting a 10BASE-F Segment to an EPIM-F1.......3-15

3.5.4 Connecting an AUI Segment to an EPIM-X

or EPIM-A .....................................................................3-17

3.5.5 Connecting a 10BASE2 Segment to an EPIM-C..........3-18

3.6 Backplane Test..........................................................................3-20

CHAPTER 4 TROUBLESHOOTING

4.1 Using LANVIEW LED

..........................................................4-1

4.2 Troubleshooting Checklist...........................................................4-4

4.3 Using the Reset Switch ...............................................................4-7

APPENDIX A SPECIFICATIONS

A.1 Physical Specifications................................................................A-1

A.2 Operating Specifications..............................................................A-1

A.3 Environmental Requirements......................................................A-2

A.4 Certification..................................................................................A-2

A.5 COM Port Pinout .........................................................................A-2

ICH1Book Page v Tuesday, August 6, 1996 3:06 PM

Contents

vi EMM-E6 Installation Guide

APPENDIX B UPGRADING THE EMM-E6

B.1 Locating BRIM Connectors......................................................... B-1

B.2 Adding EPIM

......................................................................B-2

B.3 SIMM Upgrades.......................................................................... B-3

B.3.1 Locating SIMMs..............................................................B-3

B.3.2 Installing SIMMs .............................................................B-4

APPENDIX C ETHERNET CABLING REQUIREMENTS

C.1 Network Requirements ...............................................................C-1

C.1.1 10BASE-T Twisted Pair Network....................................C-1

C.1.2 Multimode Fiber Optic Network ......................................C-3

C.1.3 Single Mode Fiber Optic Network...................................C-4

C.1.4 10BASE2 Coaxial Cable Network...................................C-5

C.1.5 Transceiver Requirements..............................................C-5

INDEX

ICH1Book Page vi Tuesday, August 6, 1996 3:06 PM

EMM-E6 Installation Guide 1-1

CHAPTER 1

INTRODUCTION

Welcome to the Cabletron Systems

EMM-E6 Installation Guide

. This

manual provides installation instructions and reference information for

the EMM-E6 Ethernet Bridge/Management Module.

1.1 EMM-E6 OVERVIEW

The EMM-E6 is a high-speed Ethernet bridge that also performs

comprehensive SNMP-based chassis and network management functions.

The EMM-E6 provides six bridge ports consisting of three chassis

interfaces, one external interface, and two Bridge/Router Interface

Module (BRIM) interfaces.

1.2 HOW TO USETHIS MANUAL

To gain a full understanding of this device and its capabilities, and to help

eliminate any potential problems during or after installation, please be

sure to read and understand all of the instructions/information in this

document and in the release notes supplied with your EMM-E6.

You should have a general working knowledge of Ethernet or IEEE 802.3

type data networks prior to installing the EMM-E6. The following

summarizes the organization of this manual.

Chapter 1,

Introduction

, discusses the use and conventions of the

EMM-E6 Installation Guide

, details the procedures to follow for

obtaining assistance from Cabletron Systems, and provides a list of

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza