Cabletron Systems SSR 2000 Manuale utente

Installing an Expansion Module on the SSR 2000 1

39-078-01

Installing an Expansion Module in the SSR 2000

Warning:Before performing any upgrade or installation procedures, ensure that the

SSR 2000 is powered off and that you are properly grounded to avoid electrostatic

discharge while working inside the SSR 2000’s chassis.

It may be necessary at some point for you to upgrade or replace your SSR 2000’s

expansion module(s) after receiving your SSR 2000 from Cabletron. You can install any of

the available expansion modules in either of the SSR 2000’s expansion slots.

Note: You can also reference material on installing an expansion module in the

SmartSwitch Router 2000 Getting Started Guide.

To install an expansion module:

1. Ensure that the SSR 2000 is powered off.

2. If your SSR 2000 is equipped for rackmountability, use the phillips-head screwdriver

to remove the mounting brackets from each side of the SSR 2000.

3. Take off the SSR 2000’s top cover.

a. Use the phillips-head screwdriver to remove the four mounting screws (two on

each side of the router, front and back) that hold the top cover on the SSR 2000.

Figure 1. Removing the SSR 2000’s cover

b. Slide the cover away from the front of the SSR 2000 about 1/2”, then lift it away

from the SSR 2000.

4. Use the phillips-head screwdriver to remove the four mounting screws in the existing

face plate or cover plate corresponding to the expansion slot where you plan to install

the expansion module. Be sure not to damage or remove the conductive tape on the

inside of the chassis, both above and below the expansion slot opening. (See Figure 2,

below.)

87654321 87654321

2000

CONSOLE

10/100 MGMT

ERR DIAG

HBT

RST

10/100BASE-TX 10/100BASE-TX

SSR-2

SYS

39-078-01

2 Installing an Expansion Module on the SSR 2000

Figure 2. Removing a face plate or cover plate (view from outside chassis)

5. From the inside of the chassis, line up the four holes in the expansion module’s face

plate with the corresponding holes around the empty expansion slot in the chassis,

and use the phillips-head screwdriver to tighten the screws (from the front) on each

side of the expansion module’s face plate to affix it to the chassis. (See Figure 3,

below.)

Note: You will probably have to gently push the expansion module’s face plate

down while lining up the first of the screws. The grounding fingers for the

10/100BASE-TX module that sits immediately below the empty expansion

slot protrude upwards to make contact with the bottom of the face plate.

Figure 3. Installing the new face plate (view from inside chassis)

6. This step applies only if you are installing a 100 Base-FX module (part number SSR-2-

FX). In order for the 100 Base-FX module to be aligned properly in the SSR 2000’s

chassis, 5-millimeter extensions must be attached to the six standoffs holding the

module in place on the SSR 2000’s motherboard.

blank expansion module face plate

Installing an Expansion Module on the SSR 2000 3

39-078-01

Figure 4 illustrates how the extensions are attached onto the standoffs on the SSR

2000’s motherboard.

Figure 4. Attaching 5-mm extensions to the standoffs on the SSR 2000 motherboard

(necessary only when installing an SSR-2-FX module)

7. Insert the expansion module from the top and ensure that it makes maximum surface

contact with its face plate.

8. Line up the two screw holes at the back of the expansion module and connect the

female stacking connector at the back of the expansion module to the male stacking

connector on the SSR 2000’s motherboard.

Warning:The female and male stacking connectors for the expansion modules are not

keyed, so it is possible to misalign the connection. Ensure that all pins fit properly into the

female stacking connector on the expansion module before applying power to the SSR

2000.

9. Use the phillips-head screwdriver to tighten all six screws that will hold the

expansion module in place in the SSR 2000’s chassis.

87654321 87654321

2000

87654321

10/100BASE-TX

CONSOLE

10/100 MGMT

ERR DIAG

HBT

SSR-2-TX

10/100BASE-TX 10/100BASE-TX

RST

SYS

SSR-2

SSR-2-FX 100BASE-FX

Lnk Act Lnk Act Lnk Act Lnk Act Lnk Act Lnk Act Lnk Act Lnk Act

2345678

39-078-01

4 Installing an Expansion Module on the SSR 2000

Figure 5. Installing an expansion module

10. Replace the SSR 2000’s cover.

When you are ready to attach the segment cables, use the procedures in “Attaching Port

Cables” in the SmartSwitch Router 2000 Getting Started Guide.

87654321 87654321

2000

1000BASE-SX

87654321

10/100BASE-TX

CONSOLE

10/100 MGMT

ERR DIAG

HBT

SSR-2-TX SSR-2-SX

10/100BASE-TX 10/100BASE-TX

Rx AN

LinkTx

Rx AN

Link

RST

SYS

SSR-2

Indice

Altri manuali Cabletron Systems Router di rete

Cabletron Systems

Cabletron Systems BRIM-WT1 Manuale utente

Cabletron Systems

Cabletron Systems MMAC-Plus 9F106-02 Manuale utente

Cabletron Systems

Cabletron Systems SSR-600 Manuale utente

Cabletron Systems

Cabletron Systems CSX200 CyberSWITCH Manuale utente

Cabletron Systems

Cabletron Systems MMAC-Plus 9T101-04 Manuale utente

Cabletron Systems

Cabletron Systems ELS100 Manuale utente

Cabletron Systems

Cabletron Systems 3H02-04 Manuale utente

Cabletron Systems

Cabletron Systems MMAC-Plus 9T106-01 Manuale utente

Cabletron Systems

Cabletron Systems SMARTSWITCH ROUTER 9032578-05 Istruzioni per il montaggio

Cabletron Systems

Cabletron Systems ESX-1380 Manuale di programmazione

Cabletron Systems

Cabletron Systems SmartSWITCH 7H02-06 Manuale utente

Cabletron Systems

Cabletron Systems BRIM-E6 Manuale utente

Cabletron Systems

Cabletron Systems SmartSwitch 8-slot Istruzioni per il montaggio

Cabletron Systems

Cabletron Systems ELS100 Manuale utente

Cabletron Systems

Cabletron Systems Spectrum EMM-E6 Manuale utente

Cabletron Systems

Cabletron Systems CSX200 CyberSWITCH Manuale utente

Cabletron Systems

Cabletron Systems MMAC-Plus 9F106-01 Manuale utente

Cabletron Systems

Cabletron Systems SSR 2000 Manuale utente

Cabletron Systems

Cabletron Systems ESX-1380 Istruzioni per l'installazione e il funzionamento

Cabletron Systems

Cabletron Systems SmartSwitch 2200 Manuale operativo

Cabletron Systems

Cabletron Systems MMAC-Plus 9W111-08 Manuale utente

Cabletron Systems

Cabletron Systems BRIM E100 BRIM-E100 Manuale utente

Cabletron Systems

Cabletron Systems SmartSwitch Router Istruzioni per il montaggio

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza