Calflame BBQ09843B Manuale utente

BEER KEG REFRIGERATOR

Model：BBQ09843B

Page. 2

INSTRUCTION MANUAL FOR Beer Keg Refrigerator

SAFETY PRECAUTIONS

Read all of the instructions before using this appliance. When using this appliance, always

exercise basic safety precautions, including the following:

1. Use this appliance only for its intended purpose as described in this operation manual.

2. This appliance must be properly installed in accordance with the installation instructions before it is

used. See the installation section for more details.

3. This appliance must be connected to a proper electrical outlet with the correct electrical supply.

4. Proper grounding must be ensured to reduce the risk of shock and ﬁre. Do not cut or remove the

grounding pin! If you do not have a three-prong electric receptacle outlet in the wall, have a certiﬁed

electrician install the proper outlet. The wall receptacle must be properly grounded.

5. Never unplug your appliance by pulling on the power cord. Always grasp the plug ﬁrmly and pull straight

out from the outlet.

6. Immediately replace worn power cords, loose plugs and power outlets. If the supply cord is damaged,

it must be replaced by the manufacturer or its service agent or a similarly qualiﬁed person in order to

avoid a hazard.

7. To reduce the risk of electric shock or ﬁre, do not use extension cords or adapters to connect the unit to

an electrical power source.

8. Unplug your appliance before cleaning or making any repairs.

9. We suggest that a certiﬁed technician perform the service if for any reason this product requires service.

10.If your old appliance is being discarded, we recommend that you remove the door and leave the shelves

in place. This will reduce the possibility of danger to children.

11.This appliance should not be recessed or built into an enclosed cabinet. It is designed for freestanding

installation only.

12.Do not operate your appliance in the presence of explosive fumes.

13.Do not tamper with the controls.

14.Do not operate this appliance when parts are missing or broken.

15.Do not use this appliance for commercial use.

16.This appliance is designed for indoor use only and should not be used outdoors.

17.To reduce the risk of injury, do not allow children to play in or on the appliance. Close supervision is

necessary when the appliance is used near children.

18.The appliance door must be closed during operation. Do not leave the door open when children are

near the dispenser.

19.Do not run cord over carpeting or other heat insulators. Do not cover the cord. Keep cord away from

trafﬁc areas, and do not submerge in water. DO NOT attempt to operate this unit with a damaged cord

or plug.

20.DO NOT roll the beer keg fridge with loaded beer kegs on carpet ﬂoor.

21.This appliance is not intended for use by young children or inﬁrm persons without supervision.

22.This appliance is NOT A TOY!

23.Young children should be supervised to ensure that they do not play with this appliance.

24.When transporting the refrigerator, keep the unit in the upright position. Do not tilt the appliance beyond

45° or place the unit in upside down position.

IMPORTANT SAFETY PRECAUTIONS OF (CARBON DIOXIDE) GAS

1. gas can be dangerous! cylinders contain high - pressure compressed gas, which can be

hazardous if not handled properly. Make sure you read and understand all the procedures for the

cylinders before installation.

2. Always connect the cylinder to a regulator! Failure to do so may cause an explosion resulting in

possible death or injury when the cylinder valve is opened,

3. Never connect the cylinder directly to the product container.

4. Always follow the correct procedures when changing cylinders.

5. Never drop or throw a cylinder.

6. Always keep cylinders away from heat. Store extra cylinder at a cool place(preferably lower than

Page. 3

70° F). Secure fasten with a chain in an upright position when storing.

7. Always ventilate and leave the area immediately if CO2 leakage has occurred!

8. There are two safety devices in the pressure system in the form of a valve. One safety feature is on the

bottle. The second is on the regulator.

9. Never attempt to reﬁll cylinder yourself. tanks can be reﬁlled at locations such as welding

supply shops, party stores, ﬁre supply shops, or where kegs are purchased.

Page. 4

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Page. 5

DANGER!

Risk of child entrapment! Before throwing away your old appliance, remove the door so that children may

not easily become trapped inside.

•Take off the doors.

•Leave the shelves or other accessories in place so that children may not easily become trapped inside.

(Note: If the refrigerator has been placed in a horizontal or tilted position for any period of time,

please wait at least 24 hours before plugging the unit in.)

PROPER LOCATION

•To ensure that your beer keg fridge works to the maximum efﬁciency it was designed for, keep it in a

location where there is proper air circulation and electrical outlets.

•Choose a location where the beer keg fridge will be away from heat and will not be exposed to direct

sunlight.

•This beer keg fridge is designed for indoor use only -- it should not be used outdoors.

•This beer keg fridge is a freestanding design and should not be placed in a built-in or recessed area.

•Beer keg fridge unit dimensions:

21.3” W x 33.20” H (with casters) x 26.60” D

•The following dimensions are recommended for clearances around the beer keg fridge:

Sides : 5” (12 cm)

Back : 5” (12 cm)

USE OF EXTENSION CORDS

Always avoid using an extension cord because of potential safety hazards in certain conditions. If it is

necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug.

And use the cord with No. 14 AWG minimum size and rated not less than 1875watts.

ASSEMBLY INSTRUCTIONS

Read assembly instructions carefully to ensure that you understand all installation

instructions before installing the beer keg fridge. If after completing the process you are still

unsure whether the beer keg fridge has been properly installed, we recommend that you contact

a qualiﬁed installer.

Note: Allow the beer keg fridge to stand in an upright position for at least 8 hours before plugging in the

unit. This is very important! Once the unit is laid on its side, the refrigeration in the refrigeration system is

shifted. The refrigerant in the refrigeration system needs to stabilize before the unit is turned on.

Installing the Casters

Follow the steps below to install the casters.

1. Empty the inside of the cabinet

completely and lay the beer keg fridge

down on it’s side. We recommend that

you place a piece of cardboard or cloth

underneath the cabinet to prevent dents

or scratches.

2. Insert the casters into the holes on the

bottom corners of the cabinet. Tighten

each caster by turning the nut clockwise

with a wrench (not provided in the kit).

3. Once all four casters have been

tightened, stand the cabinet in its upright

position.

Note: Two of the casters include locking mechanisms

to ensure the unit does not slide on hard ﬂoors. These two locking casters should be fastened at the front

Page. 6

end of the unit, with the unlocked casters fasted on the rear end.

INSTALLING THE BEER TAP

Follow the steps below to install the beer tap.

There are notches on the bottom of the draft arm

assemblythatlineupwithgroovesinsidetheopeningon

thetopofthebeerkegfridge.Alignthedraftarmwiththe

opening on the top of the unit, then place inside and twist

until secure. No screws are necessary, it locks into place

simply.

Pay attention to use the thin black gasket for assembly.

(SeeIllustrationsC&Donfollowingpage)

Also,SeeIllustrationsE&Fonfollowingpage,showing

the hose connections to regulator and the

regulator to the beer tap.

Handle

Beer

Dispenser

Tower

Beer Duct

Guard Rail

INSTALLING THE GUARDRAIL

Follow these steps below to install the guardrail.

1. Place the guardrail on top of the cabinet.

2. Alignallsupportfeetoftheguardrailwiththeholesofonthetopoftheunit.

Page. 7

INSTALLING THE REGULATOR AND THE CO2 CYLINDER

Follow these steps to safely

install the regulator and

cylinder. You must read

and understand the following

procedures for the cylinders

before installation.

NOTE: Your cylinder

has DOT (USA Department

of Transportation) approval,

however the cylinder has

been shipped empty to avoid

any possible accidents during

transportation. When you

purchase the ﬁrst keg of beer,

you must also have your

cylinder ﬁlled at your local

supplier. (See page 2, item 9 for

suggested locations within your

community.)

1. Install the gas line tube to the regulator by attaching one end of the tube to the hose barb

connection on the regulator. (See Illustration B, on page 6)

2. Insert the special washer (provided with the kit) into the regulator to cylinder attachment nut. (See

Illustration A, on page 6)

3. Attach the regulator to the cylinder by screwing the regulator nut onto the cylinder valve and

tightening with an adjustable wrench.

4. Wrap the rubber strap that is attached to the interior of beer keg fridge unit around the bottle to

secure the bottle in place (as shown above).

5. Position the cylinder so that you would be able to read the numbers on the gauges and have easy

access to shut-off valves.

DANGER!

can be dangerous! cylinders contain high-pressured gas, which can be hazardous if handled

improperly. They must be handled with care.

TAPPING THE BEER KEG – INSTALLING KEG TAP

(SINGLE-VALVE TYPE BARREL)

Follow these steps below to tap the beer keg.

1. Make sure the black pull handle of the tap is in the closed (up) position before installing it on the keg

(Fig. 1 - below). Insert the keg coupler into the locking neck of the beer keg and turn clockwise ¼ to lock

it into position (Fig. 2 - below). This means that it is secured to the keg.

2. When connecting the beer line, it is very important that the black rubber washer be installed inside the

wing nut before connecting the beer line to the tap ( See Illustration A below). Remove the black rubber

protective cap located on top of tap and screw the Wing nut with the rubber washer. Tighten it ﬁrmly by

hand. (Fig.2-below)

Page. 8

3. Attachthe line end of the tube to the hose connection on the tap. Next, secure the tube by using

theremainingself-lockingplasticsnap-onclamptoensurethattherearenoleaks.Securetheclamp

tightlywithpliers(Fig.3-below).

4. Makesurethebeertowerfaucetisintheclosed(handlepointingstraightback)positionbefore

connecting the tap to the keg. To secure the tank connection, pull the tapping handle out and push down

untilitlocksintoposition.Listenforthe“click”ofthepullhandlewhenitshiftsintothenaldownward

position(Fig.4-below).Thiswillopenthebeerand gasvalves.Thekegisnowtapped.

5. Carefullytiltthekegandresttheedgeonthekegoorsupportonthebottomoftheinteriorcabinet.

Slidethebeerkegslowly,ensuringthatitisproperlylocated(Fig.5-below)andcarefullyclosethe

door.

6. Yourbeerkegfridgecomeswitha2.5 lb. bottle, which should be able to dispense four 15 gallon

kegs of beer.

IllustrationA

Black Rubber Washer Installed in Wing Nut

Illustration B

Then Attach to Bottle Connector

Page. 9

OPERATING YOUR BEER KEG FRIDGE

Dispensing Beer

Follow the steps below to dispense beer.

1. Make sure that the beer keg fridge is plugged in properly toa115V, 60Hz,1.1Amps grounded AC power

outlet.

2. place the drip tray under beer faucet to avoid messes from excess beer.

3. Open the beer faucet by pulling the tap to wards you to dispense the beer.

Note:If for any reason the beer does not come out of the tap, please refer to the “Tapping the beer Keg

- Tap”section.

4. Increase the pressure if the beer runs too slowly.

5. Hold the glass steady at a 45˚angle. When it is 2/3 full, straighten the glass. Proper foam should be a

tight creamy head and the collar on an average glass should be 3/4” to 1” high, ideally.

Note: It is normal to see condensation from on the faucet. It is caused by the difference of temperaturetemperature

between the cold beer and the inside of the faucet when beer is fowing through the line.

CLEANING & MAINTENANCE

Flushing the tubes

Follow the steps below to clean the keg

tap and hoses.(See Illustration right)

1. Turn off completely before

attempting to clean.

2. Remove the hose from the coupler

and carefully twist the dispenser

faucet off the top the beer keg fridge.

3. Ensure that the dispenser handle is

in the down position before ﬂushing

the hose. If this is not set correctly,

water cannot ﬂow through. Hold the

open end of the hose under running

water for 3-5 minutes, while the beer

dispenser faucet drains into the sink.

This will clear any excess beer that

is trapped inside, helping to prevent

any bacteria or mold that could

accumulate inside.

4. In order to clean and remove any

excess beer that may leak into the

unit space inside the door, remove

the black rubber insulation and wipe

with a wet towel as needed.

Storage & Care

Follow the guidelines below to care for your beer keg fridge when not in use.

•Please adjust the temperature control dial to MID or LOW in colder environments because this unit does

not self-defrost and ice may build up inside the unit. The temperature control dial is located inside the

cabinet of the beer keg fridge.

•Always rinse the beer line if you do not intend to use your beer keg fridge, inside the cut out area at the

bottom , lower left.

•To avoid permanent damage to the unit, never use sharp object inside the beer keg fridge.

Page. 10

SPECIAL SAFETY INFORMATION

Important Safety Message for Draft Beer Dispensing

Yourbeerkegfridgesystemhastwosafetydevicesalreadyprovidedinthe pressure line.

Thecouplerforthisbeerkegfridgeiscompatiblewiththe¼PonyKegsizedbarrelandthe½

Barrelfullsize(USKegs).Whilethebeerkegfridgecanholdboththe5gallonCorneliusKegand

the5gallonDSystemKeg,shouldyoudecidedtoruneitheroneofthese5gallonkegs,you

may need to obtain a alternate keg connector.

Safety devices should be installed in the following places:

a. Onordirectlydownstreamfromthe regulator.

b. Onthetappingdevice.

c. In-lineinthepressuresystem

Note:LocationsAandBnotedabovearepreferable.Ifpossible,theyshouldbebuiltintothe

regulatorandtappingdevicesothattheycannotberemovedorby-passed.

Illustration C Illustration D

Indice

Altri manuali Calflame Frigorifero

Calflame

Calflame BBQ09849P Manuale utente

Manuali Frigorifero popolari di altre marche

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manuale utente

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manuale utente

Sharp

Sharp SJ-BA31IEXW2-EU Manuale utente

CORBERO

CORBERO CC2300MCW Manuale utente

KitchenAid

KitchenAid 2205264 Manuale utente

Stengel

Stengel KU 1101 A++ Manuale utente

NEFF

NEFF KI181 Series Manuale utente

Hoshizaki

Hoshizaki Reach-In Manuale utente

Amana

Amana ASD2524VES00 Manuale utente

BOMANN

BOMANN KGC 213 Manuale utente

Danby

Danby DAR044A1SLDD Istruzioni per il montaggio

Samsung

Samsung RF323TE Manuale utente

Beko

Beko CSA31022 Manuale utente

IKEA

IKEA FROSTIG C 185 E Manuale utente

Electrolux

Electrolux ER 6821 D Manuale utente

True

True TS-28 Manuale utente

Frigidaire

Frigidaire FSC23R5DW9 Manuale utente

Beko

Beko LSP4579W Manuale utente