Cama Handi-Lift ML7 Manuale utente
Installation manual
For Handi-Lift ML7
Original Version
Handi
-
Lift ML7
© 20
2
1
Page
2
Version
1.
2
Table of content
1 Introduction .............................................................................................. 3
1.1 Check the parts and drawing .................................................................. 3
1.2 Electrical installation ............................................................................. 3
Forces on the building ................................................................................ 4
Install the tower ........................................................................................ 4
3.1 Tower positioning ................................................................................. 4
Installing the lift unit .................................................................................. 7
4.1 Attach the back frame to the tower ......................................................... 7
4.2 Connect the electrical ........................................................................... 8
4.3 Connect the platform to the back frame ................................................... 9
4.4 Connect the power ............................................................................. 10
4.5 Load cell adjustment ........................................................................... 11
4.6 Handicap symbol ................................................................................ 12
Filling oil ................................................................................................ 12
Final touch ............................................................................................. 13
Install the gate ........................................................................................ 14
Installation test certificate ......................................................................... 17
Declaration A .......................................................................................... 18
Handi
-
Lift ML7
© 20
2
1
Page
3
Version
1.
2
1 Introduction
1.1 Check the parts and drawing
Before you start installing please read this installation manual.
Check the received parts for transport damage.
Next, study carefully the installation drawing that comes with the lift to ensure that all
dimensions are correct and corresponds to the installation site.
1.2 Electrical installation
If the drawing does not show where to install the Control boxes, please sort out where
they all go. Make sure that the electrical supply and electrical wiring for the Handi-Lift
are there before installing the tower and lift.
You need 1x230V with earth, 3x1,5 mm². The installation must be protected by a 10
Amp fuse and RCCB 30 mA. We recommend that you make a measurement of the
earth connection.
We recommend that you make a measurement of the earth connection.
Fig. 1
Handi
-
Lift ML7
© 20
2
1
Page
4
Version
1.
2
Forces on the building
LOAD &
FORCES
F
1
2946N
F
e
1129N
F
h
h
2300mm.
770N
2000mm.
870N
1800mm.
960N
1700mm.
1050N
1500mm.
1120N
1450mm.
1190N
Fig. 2
The tower is fixed to the floor and to the wall with M10x90mm (Class 8.8) Glue bolts.
Two bolts in the wall and three in the floor.
The given load forces applies for the total force when two bolts are used both places.
Please make sure the wall and floor materials can withstand the given loads.
Install the tower
3.1 Tower positioning
The tower is the first component to install. Dependent on the quality and straightness
of the wall- and ground material, the tower placement may need corrections.
Handi
-
Lift ML7
© 20
2
1
Page
5
Version
1.
2
Place the tower on the floor against the
wall.
Adjust the tower to be perpendicular to
the wall of the landing. (see fig. 3)
The distance between the centre of the
tower and the landing wall is given on the
installation drawing. You will also find the
distance labelled on the bottom face of
the tower.
The centre of the tower is clearly marked
with a “V” in the baseplate next to the
label (see fig. 3).
Fig. 3
Make sure the tower is in level (see fig. 4).
Fig. 4
Handi
-
Lift ML7
© 20
2
1
Page
6
Version
1.
2
Finally, adjust the tower to be vertical in both directions before fixing
it
to the wall
and the floor, so the landing fits.
Mount the bolts in the wall with glue as described on the glue package.
Fasten the nuts.
Handi
-
Lift ML7
© 20
2
1
Page
7
Version
1.
2
Installing the lift unit
4.1 Attach the back frame to the tower
Place the ba
ck frame of the lift on the floor
in front of the tower.
Fig.
5
Connectors and cables are put through the hole on both sides.
Fig. 6
Handi
-
Lift ML7
© 20
2
1
Page
8
Version
1.
2
Position the back frame to the mounting holes of the carriage.
Fasten the back frame using the four screws and washers.
Fig. 7
4.2 Connect the electrical
Leave the lift carriage and back frame in the lower position of the tower. Place the
platform on the floor in front of the back frame.
Pull the cables and mount the connectors as shown below.
Fig.
8
left
Fig.
8
right
Handi
-
Lift ML7
© 20
2
1
Page
9
Version
1.
2
Fig. 9a Fig. 9b
4.3 Connect the platform to the back frame
Mount the platform to the back
frame using
the two screws and nuts
(M12x160/M12x180).
If necessary, adjust the lower position of
the platform using the set screws.
Fig.
10
Plug the remote lead into the control board. Press the re-set button in order to start
up the system.
Fig. 11
Handi
-
Lift ML7
© 20
2
1
Page
10
Version
1.
2
Now install the control boxes
Adjust the limit switches, as shown in the photo:
Fig. 12
4.4 Connect the power
Fig. 13
The wires are connected to the safety cut-out as follows:
L1 is connected to terminal 2
Indice
Altri manuali Cama Sistema di sollevamento
Manuali Sistema di sollevamento popolari di altre marche
Genie
Genie Z-60/34 Manuale utente
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuale utente
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuale utente
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuale di programmazione
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuale di programmazione
