Campbell CS240 Manuale utente

Revision: 08/2020

Campbell Scientific, Inc.

Table of contents

1. Introduction 1

2. Precautions 1

3. Initial inspection 2

4. QuickStart 2

5. Overview 5

6. Specifications 6

7. Installation 8

7.1 Placement on a photovoltaic (PV) module 8

7.2 Mounting/cable strain relief 8

7.2.1 Adhesive mounting strip 9

7.2.2 Extreme sealing tape 9

7.2.3 Strain relief of CS240DM analog-to-digital module 11

7.3 Wiring 11

7.3.1 CS240-to-data-logger wiring 12

7.3.2 CS240DM wiring 13

7.4 Data logger programming 14

7.4.1 CS240 programming 14

7.4.1.1 Resistance measurement 14

7.4.1.2 Converting resistance measurement to temperature 15

7.4.2 CS240DM programming 15

8. Operation 16

8.1 Electrical noisy environments 16

8.2 Long cable lengths 16

8.2.1 CS240 cable resistance/long cable lengths 16

8.2.2 CS240DM long cable lengths 17

8.3 Modbus register map 18

8.4 CS240DM and Device Configuration Utility 19

9. Maintenance and troubleshooting 21

9.1 Maintenance 21

Table of Contents - i

9.2 Troubleshooting 21

Appendix A. Importing Short Cut code into CRBasic Editor 22

Appendix B. Example programs 23

B.1 CS240 two-wire configuration programs 24

B.2 CS240 four-wire configuration programs 28

B.3 CS240DM program 31

Appendix C. Sensor material properties 33

C.1 3M F9473PC adhesive 33

Table of Contents - ii

1. Introduction

The CS240 and CS240DM temperature sensors use a precision 1000 ohm class A platinum

resistance thermometer (PRT) to measure temperature. They are designed for measuring the

back-of-photovoltaic (PV) module temperature but also can be used to measure the surface

temperature of other devices. The CS240 can be measured with a 2-wire or 4-wire configuration

and is compatible with most Campbell Scientific data loggers. The CS240DM has a digital RS-485

output that can be directly read by a MeteoPV, CR6, CR1000X, or Modbus RTU RS-485 network.

Other Campbell Scientific data loggers can use an MD485 multidrop interface to read the

CS240DM output.

NOTE:

This manual provides information only for CRBasic data loggers. The CS240 is also

compatible with our retired Edlog data loggers. For Edlog data logger support, contact

Campbell Scientific. Support for Edlog data loggers is no longer free; see

www.campbellsci.com/news-edlog-retiring for more information.

2. Precautions

lREAD AND UNDERSTAND the Safety section at the back of this manual.

lDo not use epoxy to secure the sensor head to a PV module.

lBefore mounting, the installers need to wash their hands and then clean the back of the PV

module or other device with ethyl alcohol.

lDo not place tape over the sensor molding; only place tape on the metal disk portion of

the sensor.

lPrying the sensor head off will likely damage both the sensor and PV module.

lProper strain relief of the cable is required after mounting the sensor to the measurement

surface (Mounting/cable strain relief (p. 8)).

lPlacement of the cable inside a rugged conduit is advisable for cable runs over 4.5 m (15

ft), especially in locations subject to digging, mowing, traffic, power tools, animals, or

lightning strikes.

CS240 and CS240DM PT-1000 Class A, Back-of-Module Temperature Sensors 1

3. Initial inspection

lUpon receipt of the sensor, inspect the packaging and contents for damage. File damage

claims with the shipping company.

lThe model number, cable length, and cable resistance (CS240 only) are printed on a label

at the connection end of the cable. Check this information against the shipping documents

to ensure the expected product and cable length were received.

4. QuickStart

The information provided in this section is for the CS240.

A video that describes data logger programming using Short Cut is available at:

www.campbellsci.com/videos/cr1000x-data logger-getting-started-program-part-3. Short Cut is

an easy way to program your data logger to measure the sensor and assign data logger wiring

terminals. Short Cut is available as a download on www.campbellsci.com. It is included in

installations of LoggerNet, RTDAQ, PC400, or PC200W.

The following procedure also shows using Short Cut to program the CS240 and CS240DM.

1. Open Short Cut and click Create New Program.

2. Double-click the data logger model.

3. In the Available Sensors and Devices box, type CS240. You can also locate the sensor in the

Sensors >Temperature folder. Double click the sensor model. The surface temperature

defaults to degree C. This can be changed by clicking the Temperature box and selecting

one of the other options. If using the 2-wire configuration, type the Cable Resistance. This

value is unique for each CS240 and CS240DM, and is printed on the heat shrink label

attached to the sensor cable.

CS240 and CS240DM PT-1000 Class A, Back-of-Module Temperature Sensors 2

4. Click on the Wiring tab to see how the sensor is to be wired to the data logger. Click OK

after wiring the sensor.

5. Repeat steps three and four for other sensors you want to measure. Click Next.

CS240 and CS240DM PT-1000 Class A, Back-of-Module Temperature Sensors 3

6. In Output Setup, type the scan rate, a meaningful table name, and the Data Output

Storage Interval.

7. Select the measurement and its associated output option.

8. Click Finish and save the program. Send the program just created to the data logger if the

data logger is connected to the computer.

9. If the sensor is connected to the data logger, check the output of the sensor in the data

logger support software data display in LoggerNet, RTDAQ, PC400, or PC200W to make

sure it is making reasonable measurements.

CS240 and CS240DM PT-1000 Class A, Back-of-Module Temperature Sensors 4

5. Overview

The CS240 and CS240DM are surface mountable platinum resistive thermometers (PRT) that

measure back-of-module temperature for solar energy applications. They use a precision PT-1000

class A PRT to provide the highest level of accuracy. To withstand the harsh treatment commonly

seen in meteorological station installation, the sensing element is safely housed inside a specially

designed self-adhesive aluminum disk (FIGURE 5-1 (p. 5)).

The disk protects the PRT, particularly during installation, and promotes heat transfer from the

surface. An adhesive tab on the disk fastens the sensor to the measurement surface. If the

temperature may exceed 70 °C, extreme sealing tape is also required to secure the sensor.

The CS240DM includes a Campbell Scientific precision analog-to-digital, smart-sensor module

for making the measurements. The module design is optimized for the class A PRT that

minimizes self-heating and lead-wire resistance. Measurement electronics are surge protected

with 1200 V isolation and environmentally protected with a rugged overmolding with an IP65

rating.

The CS240 and CS240DM provide PV stakeholders with highly accurate back-of-module

temperature, even at long cable lengths, in power performance modeling and simulation of solar

energy applications. Back-of-module temperature is critical for any evaluation of effective

irradiance and power conversion.

FIGURE 5-1. CS240/CS240DM temperature sensor

CS240 and CS240DM PT-1000 Class A, Back-of-Module Temperature Sensors 5

Features:

lPrecision PT-1000 class A sensing element

lUser-selectable and standard cable lengths offered

lRugged design holds up in harsh conditions and conduit installations

lSelf-adhesive backing for easy mounting lasts decades

lCS240 has 2-wire or 4-wire configurations to satisfy accuracy even at long cable lengths

lCS240 compatible with Campbell Scientific CRBasic data loggers: CR6, CR3000, CR1000X,

CR800 series, CR300 series, CR1000, and CR5000

lCS240DM compatible with Campbell Scientific CRBasic data loggers: CR6, CR1000X,

CR3000 (with MD485), CR800 series (with MD485), CR300 series (with MD485), CR1000

(with MD485),

lCS240DM easily interfaces with the MeteoPV Platform without coding

lCS240DM can connect directly with Modbus RTU RS-485 Networks

lCalibration services with certification available

6. Specifications

Sensor: Precision 1000 ohm class A platinum sensing element

Class A sensor accuracy: ± (0.15 + 0.002t) °C

Temperature range: –40 to 135 °C

Temperature coefficient: TCR = 3850 ppm/K

Long-term stability: Max Ro drift = 0.04% after 1000 hours at 400 °C

CS240 measuring current: 0.1 to 0.3 mA

Disk diameter: 2.54 cm (1.0 in)

Overall sensor length: 6.35 cm (2.5 in)

Overmolded joint dimensions

Width: 1.12 cm (0.44 in)

Height: 1.47 cm (0.58 in)

Length: 5.72 cm (2.25 in)

Cable diameter: 0.622 cm (0.245 in)

Cable temperature rating: 105°C

Disk material: Anodized aluminum

CS240 and CS240DM PT-1000 Class A, Back-of-Module Temperature Sensors 6

Weight: 90.7 g (0.2 lb) with 3.2 m (10.5 ft) cable

CS240DManalog-to-digitalmodule: 24-bit ADC

A/D measurement uncertainty: ±0.015 °C

Supply voltage: 5 to 30 VDC

Power consumption: 15 mA

Surge protection: 1200 V isolation

Environmental protection: Rugged overmolding with IP65 rating

Approvals: UL AWM 2586 1000V 105 °C; CSA AWM 600V 105 °C FT1

Conforms with Electromagnetic Compatibility Directive

(EMC)

Conforms with the Restriction of Hazardous Substances

Directive (RoHS2)

Compliance: View compliance documents at:

www.campbellsci.com/cs240 or

www.campbellsci.com/cs240dm

Compliant with IEC 60751, DIN EN 60751,

Industrial Design (IEC Class 4) (according to IEC 751)

CS240 cable

Jacket material: Black semi-gloss PVC, UL VW-1 sunlight resistant for

outdoor use

Wire size and type: 24 AWG (7/32) tinned copper

Nominal wire diameter: 0.61 mm (0.024 in)

Insulation type: PVC

UL: AWM 10012 1000V 105 °C

Filler: Fibrillated polypropylene as required for uniform

round construction.

Drain: 24 AWG (7/32) tinned copper (cabled, touching foil)

Shield: Aluminum/mylar (100% coverage, 25% minimum overlap,

foil facing in)

CS240 and CS240DM PT-1000 Class A, Back-of-Module Temperature Sensors 7

Altri manuali per CS240

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Campbell Accessori

Campbell

Campbell 61302V Manuale utente

Campbell

Campbell SR50 Manuale utente

Campbell

Campbell MetSENS Series Manuale utente

Campbell

Campbell TempVue 10 Manuale utente

Campbell

Campbell HygroVUE 5 Manuale utente

Campbell

Campbell 255-100 Manuale utente

Campbell

Campbell 10162 Manuale utente

Campbell

Campbell HC2-S3-L Manuale utente

Campbell

Campbell CS210 Manuale utente

Campbell

Campbell 0871LH1 Manuale utente

Campbell

Campbell CS100 Manuale utente

Campbell

Campbell CS106 Manuale utente

Campbell

Campbell ClimaVUE 50 Manuale utente

Campbell

Campbell 05103 Manuale utente

Campbell

Campbell CS105 Manuale utente

Campbell

Campbell TB4 Manuale utente

Campbell

Campbell CS230 Manuale utente

Campbell

Campbell CS325DM Manuale utente

Campbell

Campbell TEMPERATURE PROBE 109SS Manuale utente

Campbell

Campbell CS115 Manuale utente

Campbell

Campbell CS725 Manuale utente

Campbell

Campbell Hydrosense Manuale utente

Campbell

Campbell CS505 Manuale utente

Campbell

Campbell SR50 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente