Campbell SkyVUE Pro Manuale utente

Revision:11/2020

Campbell Scientific, Inc.

Table of contents

1. General information 1

1.1 Packing list 1

1.2 General safety 1

1.3 Sensor unit safety 2

1.4 Laser safety 2

1.5 Electrical safety 3

2. Product overview 4

2.1 Introduction 5

2.1.1 Cloud height detection 6

2.1.2 Sky condition 6

2.1.3 Backscatter profile reporting 7

2.1.4 Mixing layer height 7

2.2 Optical measurement 8

2.2.1 Optical arrangement 8

2.3 Internal monitoring 8

2.4 Specifications 9

2.4.1 Measurement specifications 9

2.4.2 Mechanical specifications 9

2.4.3 Electrical specifications 10

2.4.4 Optical specifications 12

2.4.5 Environmental specifications 12

2.4.6 Communications specifications 12

3. Initial preparation and checks 13

4. Installation 14

4.1 Location and orientation 14

4.2 Grounding 15

4.3 Mounting the SkyVUE PRO 15

4.4 Tilt angle 16

4.5 Connectors and wiring 17

4.5.1 Base connectors 18

4.5.2 Wiring using supplied Campbell Scientific cables 19

Table of Contents - i

4.5.2.1 Power connections 20

4.5.2.2 Communications connections 21

4.5.3 USB connection 22

4.5.4 SDI-12 connection 22

4.6 Connecting the back-up battery 22

4.6.1 Removing the cover 23

4.6.2 Removing the enclosure lid 23

4.7 Bird spike kit 24

4.8 Storage information 26

5. Operation 27

5.1 Terminal mode 27

5.1.1 Entering/exiting the SkyVUE PRO terminal mode 27

5.1.2 Terminal mode commands general 28

5.1.3 Terminal mode command examples 29

5.1.4 Application command message types 44

5.1.5 MCFG command message types 46

5.1.6 Measurement and message intervals 47

5.1.7 Status command 49

5.1.8 Message polling 58

5.1.9 Loading a new operating system (OS) 59

5.1.10 Stratocumulus backscatter calibration 62

5.1.11 CRC-16 codes on terminal commands 64

5.1.12 Service command 65

5.1.13 Locked features 66

5.2 Restoring factory defaults 66

5.3 LED indicator 67

6. Messages 68

6.1 Data messages general 68

6.2 Checksums used in SkyVUE PRO messages 68

6.3 CS messages 69

6.3.1 MESSAGE 001 (no profile, no sky condition) 69

6.3.2 MESSAGE 002 (Profile, no sky condition) 73

6.3.3 MESSAGE 003 (no profile, sky condition) 76

6.3.4 MESSAGE 004 (profile, sky condition) — default message 78

6.3.5 MESSAGE 005 (no profile, sky condition, mixing layer heights) 82

6.3.6 MESSAGE 006 (profile, sky condition, mixing layer heights) 85

Table of Contents - ii

6.4 CL31 messages 89

6.4.1 MESSAGES 101 - 106, (CL31 MESSAGE 1) 89

6.4.2 MESSAGE 005 (no profile, sky condition, mixing layer heights) 90

6.4.3 MESSAGES 107 - 112, CL31 Message 2 94

6.5 CT25K messages 98

6.5.1 MESSAGE 113, CT25K Data Message No. 1 98

6.5.2 MESSAGE 114, CT25K Data Message No. 6 101

7. Maintenance 103

7.1 General 103

7.2 Cleaning 103

7.3 Removing the cover 104

7.4 Removing the enclosure lid 105

7.5 Diagnostic LED indicators within the enclosure 105

7.6 Electrical safety testing 107

Appendix A. Measurement of the attenuated backscatter profile 108

A.1 Initial measurement 108

A.2 Backscatter onset height detection 108

A.3 Produce attenuated backscatter output message 109

Appendix B. Cloud height calculation 110

Appendix C. Sky condition algorithm description 111

Appendix D. Replacing the SkyVUE PRO PSU 113

Appendix E. SkyVUE PRO Laser/APD module replacement 115

Appendix F. SkyVUE PRO TOP board replacement 118

Appendix G. Self-diagnostic information 124

List of figures

FIGURE 2-1. Principle of operation 8

FIGURE 2-2. SkyVUE PRO dimensions 10

FIGURE 2-3. PSU types 11

FIGURE 4-1. Mounting base footprint 16

FIGURE 4-2. Setting the tilt angle 17

FIGURE 4-3. Connector layout 18

FIGURE 4-4. Cable connections 21

FIGURE 4-5. USB port 22

Table of Contents - iii

FIGURE 4-6. Connecting battery 22

FIGURE 4-7. Removing the cover 23

FIGURE 4-8. Removing the enclosure lid 24

FIGURE 4-9. Ceilometer bird spike kit installed 25

FIGURE 4-10. Preparing the SkyVUE PRO for installing the bird spikes 25

FIGURE 4-11. Attaching bird spikes to the SkyVUE PRO cowl 26

FIGURE 5-1. Restoring factory defaults 67

FIGURE 5-2. LED indicator 67

FIGURE 7-1. Removing the cover 104

FIGURE 7-2. Removing the enclosure lid 105

FIGURE 7-3. Diagnostic LED indicators 106

List of tables

Table 1-1: Packing list 1

Table 4-1: Function of the connector pins for the mains connector 18

Table 4-2: Function of the connector pins for the blower/heater connector 19

Table 4-3: Function of the connector pins for the communications connector 19

Table 5-1: Summary of the terminal mode commands available 30

Table 5-2: Summary of applications and applied settings for SkyVUE PRO 45

Table 5-3: Summary of message ID and descriptions 46

Table 6-1: Most significant alarm word for CS messages 70

Table 6-2: Middle alarm word for CS messages 71

Table 6-3: Least significant alarm word for CS messages 72

Table 6-4: Most significant alarm word for CS31 messages 91

Table 6-5: Middle alarm word for CS31 messages 92

Table 6-6: Least significant alarm word for CS31 messages 92

Table 6-7: Most significant alarm word for CT25K messages 99

Table 6-8: Second alarm word for CT25K messages 100

Table of Contents - iv

1. General information

1.1 Packing list 1

1.2 General safety 1

1.3 Sensor unit safety 2

1.4 Laser safety 2

1.5 Electrical safety 3

1.1 Packing list

The following table lists the products shipped with the SkyVUE PRO.

Table 1-1: Packing list

Description Quantity

Ceilometer 1

Power supply cable 1

Data cable 1

Bolt, sleeve anchor 4

Cable, USB type A plug to type B plug, 2 m 1

4 mm Allen key 1

Calibration plate 1

1.2 General safety

This manual provides important safety considerations for the installation, operation and

maintenance of the SkyVUE™PRO. These safety considerations are classified into three levels:

WARNING:

Warnings alert the installer or user to serious hazards. Ignoring these warnings could result in

injury or death and/or irrevocable damage to the sensor unit.

SkyVUE™PRO (CS135) LIDAR Ceilometer 1

CAUTION:

Cautions warn of potential hazards. Ignoring these cautions could result in the sensor being

damaged and data being lost.

NOTE:

Notes highlight useful information in the installation, use and maintenance of this product.

These should be followed carefully in order to gain the maximum benefit from the use of this

product.

1.3 Sensor unit safety

The SkyVUE PRO sensor has been checked for safety before leaving the factory and contains no

internally replaceable or modifiable parts.

WARNING:

Do not modify the SkyVUE PRO unit. Such modifications will lead to damage of the unit and

could expose users to dangerous light levels and voltages.

WARNING:

Do not attempt to repair the SkyVUE PRO unit without consulting Campbell Scientific.

CAUTION:

Ensure that the correct voltage supply is provided to the sensor.

1.4 Laser safety

The SkyVUE PRO sensor incorporates an InGaAs laser diode which is rated as a class 3B device.

This is an embedded laser where the output from the sensor unit, through the optics, is

minimized to class 1M. This classification indicates that viewing of the beam with the naked eye is

safe but looking directly into the beam with optical instruments, e.g. binoculars can be

dangerous.

From the laser head the output has the following characteristics:

Maximum average power: 15.0 mW (through 50 mm)

Maximum pulse energy: 1500 nJ (through 50 mm)

Pulse duration: 100 ns

Pulse frequency: 10 kHz

Wavelength: 912 nm ± 5 nm

SkyVUE™PRO (CS135) LIDAR Ceilometer 2

Tested to: EN 60825-1:2014

Half angle divergence: 0.44 mrad

The sensor is marked with the following warning information:

INVISIBLE LASER RADIATION

DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS

CLASS 1M LASER PRODUCT

WARNING:

Removing the laser module with the power applied to the SkyVUE PRO may expose the user

to hazardous class 3B laser radiation.

No attempt should be made to operate the laser module outside of the housing.

WARNING:

Annually, check that the laser warning label on the sensor is still visible and can be clearly

read.

When installing the sensor, avoid pointing the laser housing towards areas where binoculars

are in common use.

WARNING:

Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

1.5 Electrical safety

Because the sensor is powered from potentially hazardous mains voltages, the power-supply

should be wired only by personnel qualified to install electrical equipment. For permanent

outside installations, this usually requires a certified electrician who is also familiar with local

electrical and safety legislation. Some general guidance is given in Connectors and wiring (p. 17),

but the responsibility for the installation lies with the installer.

The unit is tested for electrical safety before dispatch but may need subsequent testing according

to local practice.

NOTE:

The unit should only be serviced by trained personnel.

SkyVUE™PRO (CS135) LIDAR Ceilometer 3

WARNING:

Removal of electronic module covers or connectors while the unit is powered will expose the

operator to potentially hazardous voltages and risk damage to the sensor.

The SkyVUE PRO has electrical and laser warning labels on the exterior and interior of the unit.

It is recommended that the hood and access panel door are not opened in conditions of rain,

hail or snow.

Isolate the sensor before removing internal components, including the cover to the avalanche

photodiode (APD) module. Only trained personnel should disassemble the instrument.

Mains connectors are shrouded to prevent touching of the contacts. The mains supply should be

isolated when connecting and disconnecting the cables to the sensor.

Where an isolator switch is fitted, this shall be a two-pole isolator, located as near to the sensor

as possible.

The SkyVUE PRO must be properly grounded by a licensed and qualified electrician to protect

against voltage leakage shock risk (Grounding (p. 15)).

Campbell Scientific recommends that RCD protection units be used with all sensors. See Power

connections (p. 20) for further information.

Mains powered heaters are enclosed to prevent contact.

CAUTION:

When powered, the heaters may operate automatically and without warning. They may

remain hot when not powered. Follow the isolation precautions, to avoid shock and burn

hazards.

The sealed battery has cables and protected connectors to prevent shorts. Avoid shorting the

battery to protect it from damage and to avoid burns to personnel through contact with hot

surfaces.

2. Product overview

2.1 Introduction 5

2.2 Optical measurement 8

2.3 Internal monitoring 8

2.4 Specifications 9

SkyVUE™PRO (CS135) LIDAR Ceilometer 4

2.1 Introduction

The SkyVUE PRO is a light detection and ranging (LIDAR) ceilometer that emits short pulses of

near infrared light into the atmosphere from a semiconductor laser. The pulses of infrared light

are scattered back by aerosols including cloud droplets. The time between transmission of the

pulse and the return signal gives the range, and therefore height, of the scattering aerosols. The

variation in the strength of the back-scattered light signal with height gives a profile of scatter

coefficients and allows identification of cloud bases. If significant scattering is detected without a

defined cloud base, then a vertical visibility can be calculated.

The control system of the SkyVUE PRO is divided into three modules, DSP, TOP and PSU as

follows:

DSP (Digital Signal Processor) is the main data processing and communications unit of the

SkyVUE PRO. It hosts two separate time keeping circuits that are cross checked. An alarm is

triggered if the circuits disagree.

SkyVUE™PRO (CS135) LIDAR Ceilometer 5

Altri manuali per SkyVUE Pro

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Campbell Accessori

Campbell

Campbell KH20 Manuale utente

Campbell

Campbell LWS-L Manuale utente

Campbell

Campbell 237 Manuale utente

Campbell

Campbell CS505 Manuale utente

Campbell

Campbell HS2 Manuale utente

Campbell

Campbell CS511 Manuale utente

Campbell

Campbell cs215 Manuale utente

Campbell

Campbell Hydrosense Manuale utente

Campbell

Campbell CS100 Manuale utente

Campbell

Campbell ClimaVUE 50 Manuale utente

Campbell

Campbell TEMPERATURE PROBE 109SS Manuale utente

Campbell

Campbell CS100 Manuale utente

Campbell

Campbell WXT520 Manuale utente

Campbell

Campbell 253 Manuale utente

Campbell

Campbell LWS Manuale utente

Campbell

Campbell ICEFREE3A Manuale utente

Campbell

Campbell Wintersense SDI-12 Manuale utente

Campbell

Campbell 52202 Manuale utente

Campbell

Campbell Met One 034B Manuale utente

Campbell

Campbell 253 Manuale utente

Campbell

Campbell CS725 Manuale utente

Campbell

Campbell 255-100 Manuale utente

Campbell

Campbell CWS Series Manuale utente

Campbell

Campbell SDM-CVO4 Manuale del proprietario

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente