Campbell Redwing CDMA1X Manuale utente

INSTRUCTION MANUAL

Redwing CDMA1X (C3111)

Airlink Cellular Modem

October 2006

Campbell Scientific (Canada) Corp.

Instruction Manual for use in

IS-95B Circuit Switched/Voice Mode

WARRANTY AND ASSISTANCE

This equipment is warranted by CAMPBELL SCIENTIFIC (CANADA) CORP. (“CSC”) to be

free from defects in materials and workmanship under normal use and service for twelve

(12) months from date of shipment unless specified otherwise. ***** Batteries are not

warranted. ***** CSC's obligation under this warranty is limited to repairing or replacing (at

CSC's option) defective products. The customer shall assume all costs of removing,

reinstalling, and shipping defective products to CSC. CSC will return such products by

surface carrier prepaid. This warranty shall not apply to any CSC products which have

been subjected to modification, misuse, neglect, accidents of nature, or shipping damage.

This warranty is in lieu of all other warranties, expressed or implied, including warranties of

merchantability or fitness for a particular purpose. CSC is not liable for special, indirect,

incidental, or consequential damages.

Products may not be returned without prior authorization. To obtain a Return Merchandise

Authorization (RMA), contact CAMPBELL SCIENTIFIC (CANADA) CORP., at (780) 454-

2505. An RMA number will be issued in order to facilitate Repair Personnel in identifying

an instrument upon arrival. Please write this number clearly on the outside of the shipping

container. Include description of symptoms and all pertinent details.

CAMPBELL SCIENTIFIC (CANADA) CORP. does not accept collect calls.

Non-warranty products returned for repair should be accompanied by a purchase order to

cover repair costs.

Redwing CDMA Table of Contents

1. Introduction..................................................................1

2. Specifications ..............................................................1

2.1 Base Station Requirements .......................................................................1

2.2Datalogger Site Equipment.......................................................................1

2.3 Power Considerations ...............................................................................2

3. Configuration ...............................................................2

3.1 Establish Cellular Service.........................................................................2

3.2Program the Modem .................................................................................2

3.3 HyperTerminalSetup................................................................................3

3.4 Programming the Redwing’s Phone Number ...........................................3

3.5 Programming the Redwing for use with a datalogger ..............................4

3.6 Setup LoggerNet (Option A) ....................................................................5

3.7 Setup LoggerNet (Option B) ....................................................................6

4. Programming the Redwing for Use with a Datalogger

................................................................................................................................................6

This is a blank page.

Redwing CDMA1X AirLink Cellular

Modem

1. Introduction

The Redwing CDMA1X modem is a full-duplex, digitalcellular modem that

communicates with a base station PC via Code Division Multiple Access

(CDMA) network and Public Switched Telephone Network (PSTN). The

Redwing CDMA1X modem is for use on Bell, Aliant, ManitobaTel, and

SaskTelnetworks only.

2. Specifications

2.1 Base Station Requirements

xPC with Hayes-compatible modem, running Campbell Scientific’s

LoggerNet or PC400 software.

xSubscription to Bell, Aliant, ManitobaTel,orSaskTelCDMA networks

with coverage at the datalogger site.

2.2 Datalogger Site Equipment

xRedwing CDMA1X modem—includes power cable; the modem is

configured using the Hyperterminalprogram prior to installation

xDatalogger—CR510, CR10(X), CR23X, CR7, CR800, CR1000, CR5000,

or CR2XX

xSC105 or SC932A Interface—connects the modem to the CR510,

CR10(X), or CR7 dataloggers’ CSI/O port

xL14392Null Modem Cable—connects the modem to the CR23X, CR800,

CR1000, CR2XX, or CR5000 RS-232port

xL14394 Redwing Mounting Kit—includes mounting hardware for

securing the modem to below referenced environmentalenclosure.

xAntenna—the following antennas are available from Campbell Scientific;

sites near the edge of the CDMA coverage mayrequire the Yagi antenna.

Contact a CSC Applications Technician for help in determining the best

antenna for your application.

oL14453 Omni 0 dBd ½ Wave Dipole Whip Cellular Antenna

oL14454 Yagi 8 dBd Cellular Antenna with 10' Cable

xPower Supply (see power considerations)

xEnvironmentalEnclosure— ENC 10/12, ENC 12/14, or ENC 16/18

Redwing CDMA1X AirLink Cellular Modem

2.3 Power Considerations

xA power cable included with the modem connects to the datalogger's 12V

or switched 12V terminal. Connection to the switched 12V terminal

allows the datalogger to switch power to the modem during scheduled

transmission intervals if desired.

xWhen using the switched 12V terminal, the modem can typically be

powered with a BP12battery, CH100 charger/regulator, and MSX10 solar

panel.

3. Configuration

3.1 Establish Cellular Service

Prior to contacting the cellular service provider*, have the following

information on hand:

1. Electronic SerialNumber (ESN). The ESN is found on the

unit label.

2. Desired area code and localprefix. Choose the same area

code and prefix as the calling PC to ensure that calls are

billed at localrates, even if the phone is used outside the

localcalling area.

*For modem activation, further information, and assistance in selecting the

most suitable cellular plan, please call 1-866-928-4465 or email

info@thinktel.ca

NOTE: Indicate to the account representative that you would like to open a

new account using your modem in IS-95B circuit switched/voice mode. The

service provider does not need the Redwing modem to activate the account.

3.2 Program the Modem

Items needed:

xComputer with a COM port.

x9-pin cable to connect between the computer and the Redwing.

xA terminalprogram on the computer “Hyperterminal”.

x12volt DC applied to the Redwing.

xAntenna on the Redwing (for over-the-air updates).

xCDMA account.

Redwing CDMA1X AirLink Cellular Modem

3.3 Hyperterminal Setup

Under “Connect using”, select the COM port you will be using.

Set COM Properties to:

Bits per second (baud) = 115200

Data bits = 8

Parity= None

Stop bits = 1

Flow control= None

Apply power to the modem and connect it to the computer via the 9-pin serial

cable.

3.4 Programming the Redwing’s Phone Number

Your provider should give you two numbers to program into the Redwing, the

MDN (Mobile DirectoryNumber) and MIN (Mobile Identification Number).

In most cases these numbers are the same.

Perform the following steps substituting the MDN and MIN with yours.

AT Commands to be typed are in bold. Follow each AT command string by

pressing the Enter keyand verifythe response.

Redwing CDMA1X AirLink Cellular Modem

Step AT Commands Response Description

AT+WSPC=1,xxxxxx (where

xxxxxx represents the lock code of

your modem.

Example AT+WSPC=1,123456)

Unlocks the module for service

provisioning AT commands.

AT+WMDN=[MDN]

Example:

AT+WMDN=4352551212

Enter the MDN here. The MDN is

the number used to dialthis device.

AT+WIMI=31000[MIN]

Example:

AT+WIMI=310004352551234

Enter the MIN here. The 31000

must precede the MIN. The MIN

is the number used to identifythis

device on the cellular provider’s

network. This number maybe the

same as the MDN.

OK Commits the changes done during

the service programming session.

4AT+WCMT=1

+WIND:8

Commission of these changes will

force a software reset of the

module.

5AT+CDV*22890

+WORG:*22890

+WCNT:3

+WOT1:”Programming in progress”

+WOTS:”SPL unlocked”

+WOTP:”PRL Download OK”

+WOTM:”MDM Download OK”

+WOTC:”Commit Successful”

+WOT2:”Programming Successful!”

*results mayvary*

Initiates over-the-air update. You

must have cellular coverage with

good signalstrength for this to be

successful.

There are no O’s in the above strings, theyare Zero’s.

NOTE

3.5 Programming the Redwing for use with a datalogger

The Redwing needs a few settings changed in it to power-up readyto work

with the datalogger.

Redwing CDMA1X AirLink Cellular Modem

Step AT Commands Response Description

6ATS0=1+CICB=0 OK Sets auto answer in data mode.

7AT+IFC=0,0 OK Disables localflow control.

Sets the Redwings RS232baud

rate and saves settings.

Use the following to determine

baud rate:

CR800

CR1000

CR5000

115200

CR23X 38400

AT+IPR=[baud rate]; &W

Example:

AT+IPR=9600; &W

CR10(X)

CR510

CR200

CR7

9600

In the above strings, all “0” = zero.

NOTE

Remove the power from the modem and power it up again. It should be ready

to use at the baud rate set in Step 8. Test the communications before deploying

the modem.

3.6 Setup LoggerNet (Option A)

1. Select Add Root | TapiPort.

2. Add a TapiRemote to the TapiPort.

3. Add a datalogger to the TapiRemote.

4. On the TapiPort page:

a. Select Communications Enabled.

b. If you are using the Call-back feature of the datalogger on anyof

your stations, select Call-Back Enabled.

c. Select your installed modem on the Tapi Line.

d. Extra Response Time can remain as 0 seconds.

5. On the TapiRemote un-check “Use Tapi Dialing Properties.“

Redwing CDMA1X AirLink Cellular Modem

6. Enter the phone number of the CDMA phone.

7. Apply the changes and test.

3.7 Setup LoggerNet (Option B)This is a blank page.

2.Select Add Root | ComPort.

3. Add a PhoneBase to the ComPort.

4. Add a PhoneRemote to the Phone Base.

5. Add a datalogger to the Phone Remote.

6. On the ComPort page:

a. Select Communications Enabled.

b. If you are using the Call-back feature of the datalogger on anyof

your stations, select Call-Back Enabled.

c. Select the ComPort that is connected to your modem from the

drop-down menu.

d. Extra Response Time can remain as 0 seconds.

7. On the PhoneBase page:

a. Select Communications Enabled.

b. Select the modem that you are using from the Modem Type list.

c. For CR10(X), CR510, CR7, 21X, or CR200 dataloggers, set the baud rate

to 9600. For CR23X or CR5000 dataloggers, set the baud rate to 38400

(when using the RS232port).

d. Extra Response Time can remain at 0 seconds.

8. On the PhoneRemote page:

a. Select Communications Enabled.

b. The Delaycan remain at 0 milliseconds.

c. Enter the Phone Number.

9. Apply the changes and test.

Indice

Altri manuali Campbell Modem

Campbell

Campbell RavenXTG GPRS/EDGE Manuale utente

Campbell

Campbell CS-SRM Manuale utente

Campbell

Campbell COM9602 Manuale utente

Campbell

Campbell DC112 Manuale utente

Campbell

Campbell Sierra Wireless RavenXTV Manuale utente

Campbell

Campbell IPn3Gb Manuale utente

Campbell

Campbell R410 Manuale utente

Campbell

Campbell Raven II Manuale utente

Campbell

Campbell DCP-Intelimax Manuale utente

Campbell

Campbell COM300 Manuale utente

Campbell

Campbell COM210 Manuale utente

Campbell

Campbell Raven110 Manuale utente

Campbell

Campbell RF401 Manuale utente

Campbell

Campbell Redwing 100 Manuale utente

Campbell

Campbell C311 Manuale utente

Campbell

Campbell 4GMini Manuale utente

Campbell

Campbell LS300G Manuale utente

Campbell

Campbell Airlink Raven Manuale utente

Campbell

Campbell RavenXT-Series Manuale utente

Campbell

Campbell COM220 Manuale utente

Campbell

Campbell DCSCOM Manuale utente

Campbell

Campbell LS300G-EU Manuale utente

Campbell

Campbell Sierra Wireless AirLink RV50 Manuale utente

Campbell

Campbell Sierra Wireless AirLink RV50 Manuale utente

Manuali Modem popolari di altre marche

Davicom

Davicom DM562AP Manuale utente

EpiValley

EpiValley TATA indicom SXC-1080 Manuale utente

Zte

Zte WiMAX Manuale utente

Intelimax

Intelimax MA-2060 Manuale utente

SMC Networks

SMC Networks D3CM1604V Manuale per l'uso e la cura

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuale utente

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuale utente

Samsung

Samsung AceLink SAM-335A Manuale utente

Enfora

Enfora Enabler-G Guida rapida alla configurazione

iRZ

iRZ ATM2-232 Manuale utente

Zhone

Zhone 6310 Manuale utente

Paradyne

Paradyne Hotwire 7976 Manuale utente

US Robotics

US Robotics 3453C Manuale utente

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuale utente

Zte

Zte MF823 Manuale utente

Four-Faith

Four-Faith F1403 Manuale utente

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuale utente

Gemtek

Gemtek WiMAX WIXFBR-103 Manuale utente