Candeo C202 Manuale utente
Candeo Rotary Zigbee Dimmer Switch - C202 / C202N
• Zigbee AC phase cut dimmer based on latest Zigbee 3.0 protocol
• 220V-240V AC Input and Output Voltage
• Supports resistive loads and capacitive loads
• Trailing edge control
• Enables ON/OFF control and dimming of connected triac dimmable led lights or led drivers
• Zigbee end device that supports Touchlink commissioning
• Can directly pair to a compatible Zigbee remote via Touchlink without coordinator
• Supports self-forming Zigbee network without coordinator and add other devices to the network
• Supports nd and bind mode to bind a Zigbee remote
• No neutral required
• Radio Frequency: 2.4GHz
• Waterproof grade: IP20
Features
Specications
Input Voltage 220V-240V ~ 50Hz
Power Load 10-250VA LED
10-250W Halogen
Minimum Load per lamp 5W
Dimmer Mode Trailing Edge
Control Method Smart control /
multi-way switching
C202 C202N
This dimmer is a Zigbee rotary dimmer switch
for dimmable LED lamps.
The minimum brightness setting of the dimmer
can be adjusted to achieve the optimum
dimming range for a particular load, as detailed
in the Minimum Brightness Setting section.
CE certied
This product is designed for indoor use only.
Do not attempt to open the product to
examine or repair.
Do not expose the product to moisture or
liquids
Do not dispose of with household waste
Safety Warnings and notes
• Turn O Mains Power before installing the device
• Certain light sources may not behave according to the power rating when used with a dimmer. An overload
will result in the safety features switching the dimmer o. We recommend only using this dimmer within the
suggested load, and with high quality dimmable bulbs.
• Please ensure that your bulbs or lamps are minimum 5W and the total load is minimum 10W. Results may
vary with low quality bulbs or lamps, and with a low power load you may need to t a bypass on the rst
lamp in the circuit.
Please read all of the instructions prior to installation
Candeo Rotary Zigbee Dimmer Switch - C202 / C202N
Installation
1. Turn o the power.
i. To avoid electrical shock and/or equipment damage, disconnect electrical power at the main fuse or
circuit breaker before installation and maintenance.
ii. Be aware that even if the circuit breaker is o, some voltage may remain in the wires — before
proceeding with the installation, be sure no voltage is present in the wiring.
2. Connect the device according to the diagrams shown below for either a 1-way or 2-way/multiway system.
One-way system
Two-way / multiway system
• Two-way and Multiway switching can be achieved using
push/retractive switches. (Please note that toggle (on/o)
switches are not supported.)
• Once connected with a push switch, press the switch
once to switch ON/OFF, and press and hold it to increase
or decrease the brightness level.
Caution: If in
any doubt about
how to install the
switch, please
consult a qualied
electrician.
3. After successfully wiring the switch, turn the power back on.
Candeo Rotary Zigbee Dimmer Switch - C202 / C202N
Zigbee conguration
1. Factory Reset the switch.
i. Turn on the light, press the knob 5 times with a long press on the fth time (3 seconds).
ii. Once reset successfully, the lamp will blink 5 times.
Note: All conguration parameters will be reset after the device is reset or removed from the network.
2. Zigbee Network Pairing through Coordinator or Hub such as Smartthings or Philips Hue. (Adding to
Zigbee Network)
i. From your Zigbee Controller or hub interface, choose to add a lighting device and enter Pairing Mode
as instructed by the app or Hub’s documentation.
ii. Turn on your lamp, then double press the knob, with a long press on the second time. The light will
blink twice to indicate it is in network pairing mode, which will last for 15 minutes. If your connection
attempt times out, repeat this step if necessary.
iii. When successfully paired the light will blink once, and then stay continuously on. The device can
now be controlled through your controller or hub interface.
Setting the Minimum Brightness
1. Turn on the light, then press the knob 3 times. The light will blink twice showing that the device is in
conguration mode.
2. Adjust the minimum brightness to the level you are satised with, then press the knob once to save it.
Troubleshooting
If your lights will not turn completely o, or they are ickering at low levels:
Diagnosing this issue can be complicated and often dependent on many variables that are unique to the wiring
in your house.
However, the most common cause is due to either the total load of the lights being too low, or the wattage of
one particular bulb being too low. Please ensure that each lamp is minimum 5W although 10W+ will give better
results. Please also ensure that the total load is minimum 10W.
If the problem persists, please try increasing the minimum brightness setting of the switch by following the
steps above.
If increasing the minimum brightness did not solve the problem, we suggest either increasing the load on the
circuit by using higher power lamps, or by tting an LED bypass over the rst lamp in the circuit.
Candeo Rotary Zigbee Dimmer Switch - C202 / C202N
For further support please go to www.candeo.io
Advanced Zigbee conguration
1. TouchLink to a Zigbee Remote
i. Turn on the light, press the knob 3 times with a long press on the third time (3 seconds).
ii. The light will blink 3 times and then stay continuously on to show that the device is in TouchLink
commissioning mode. This times out after 3 minutes, after which repeat this step if necessary.
iii. Bring the remote or touch panel within 10cm of the switch.
iv. Set the remote or touch panel into TouchLink commissioning mode, by following the instructions in
the corresponding remote or touch panel manual.
v. Once connected, the light will blink 10 times, and you can control your lights remotely.
• Using directly via Touchlink (with neither device added to a Zigbee network), each device can link
with 1 remote.
• Using Touchlink when both devices are added to a Zigbee network, each device can link with max. 30
remotes.
• After Touchlink pairing, the device can be controlled by the linked remotes.
Notes:
2. Find and Bind Mode
Note: Make sure the device and remote are already added to the same Zigbee network.
i. Turn on the light, press the knob 4 times with a long press on the fourth time (3 seconds).
ii. The light will blink 4 times and then stay continuously on to show that the device is in Find and Bind
Mode. This times out after 3 minutes, after which repeat this step if necessary.
iii. Set the remote or touch panel (target node) into nd and bind mode, and enable it to nd and bind
initiator. Please refer to the corresponding remote or touch panel manual.
iv. There should now be an indication on the remote or touch panel that it has binded to the device
successfully and can now control it.
Instructions version: 2202.1
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Candeo Interruttore
