Carrier P/N 33CSSN2-MH Manuale utente

OWNER'S MANUAL

P/N 33CSSN2-MH

Digital Thermostat

Designed specifically for the Lodging Industry

Use with most Air Conditioning & Heating Systems

including: 1 or 2 Stage Electric Cooling & Gas Heating,

Heat Pump, Electric, PTAC or Hydronic Heat.

Commercial Systems & Services Carrier Corporation 9/00

For Fan Coil Applications: Auto Changeover is available in 4 pipe configuration,

or in 2 pipe systems with Electric Heat, or when used with 33CSWCO-FC

accessory, auto changeover sensor.

Displays Setpoint, Only

Easy, Pushbutton Control

Adjustable Setpoint Limits

Large, Easy To Read Display

Multi Fan Speed Control

Heating / Cooling

Auto Changeover

WARMERCOOLER

F / C

FAN

FAN AUTO

TO SET, PRESS OR

Carrier

Table Of Contents

FRONT PANEL

DISPLAY

BASIC OPERATION

ADVANCED SETUP

EQUIPMENT SETUP TABLE

ABOUT ADVANCED OPERATION

WARRANTY

Page 1

CAUTION

Follow Installation Instructions before proceeding.

SET THERMOSTAT TO MODE “OFF” PRIOR TO

CHANGING SETTINGS IN SETUP OR RESTORING

FACTORY DEFAULTS.

P/N 33CSSN2-MH

Commercial Systems & Services Carrier Corporation 9/00

Front Panel - Normal Display

Page 2

Liquid Crystal Display

Up/Down Buttons

F / C Button

Fan Button

WARMERCOOLER

F / C

FAN

FAN AUTO

TO SET, PRESS OR

Desired Set Temperature

Indicates desired room temperature.

Fan Operation Indication - Up to 3 Speeds

When FAN AUTO is displayed, the fan speeds

will increase or decrease based on

temperature demand.

Setup Indication

Indicates the thermostat is in the Advanced

Setup mode. These icons indicate the

parameter to be adjusted. (Displayed in

Setup mode only)

Degrees F or C Indication

Indicates if the setpoint readout is in Fahrenheit

or Centigrade.

Cooling or Heating Indicators

Indicates that the Diagnostic Mode is active.

Display

Page 3

FAN AUTO

FAN ON

FAN LOW

FAN MED

FAN HIGH

TO SET, PRESS OR

CYCLES/HOUR

COOLING

HEATING

DEADBAND

OFF MINMAX SETPOINT

EQUIPMENT TYPE #

FAN PURGE

ROOM TEMP

buttons.

In any mode, adjust the

desired Set Temperature

with

Select Desired Temperature

Fan Operation

Page 4

Basic Operation

On, Auto, Low, Medium & High speed fan indicators.

When Fan Auto is displayed, the fan speeds

will increase or decrease based on

temperature demand.

For configurations with a single speed fan, pressing FAN will toggle

operation between Fan On and Fan Auto.

The example below illustrates a 3 speed fan system. Your system

may not have 3 fan speeds, so it may vary from this example.

Press

FAN

Press Press Press Press Press

FAN FAN FAN FAN FAN

LOW SPEED MED SPEED HIGH SPEEDAUTOOFF

FAN AUTO

FAN ON

FAN LOW

FAN MED

FAN HIGH

FAN AUTO

TO SET PRESS, OR

Advanced Setup IAdjusting Setpoint Limits

Press

To exit setup

screens:

Adjust the minimum

temperature limit.

(60 - 85)

Default = 67 degrees

Adjust the default

temperature when the

unit is powered up or

turned on.

(60 - 85)

Default = 72 degrees

Adjust the maximum

temperature limit.

(60 - 85)

Default = 80 degrees

F / C

Press the Fan button

for 5 seconds to enter

these Setup screens.

Note: Set the thermostat to ‘OFF’ mode before adjusting settings.

FAN

NOTE: Each step’s description is

located at

corner of the

easy reference.

the top right

display for

TO SET PRESS, OR

MIN SETPOINT

SETPOINT

MAX SETPOINT

Press

FAN

Note: The user may select any desired temperature

between 60 and 85 degrees. However, the thermostat

will not attempt to cool or heat the room beyond the

minimum or maximum setpoint limits.

Page 5

TO SET PRESS, OR

Advanced Setup II INSTALLATION

Press

Press the Fan button

for 10 seconds to enter

these Setup screens.

NOTE: Each step’s description is

located at

corner of the

easy reference.

the top right

display for

FAN

Adjust the minimum

temperature setpoint

that is used when the

thermostat indicates OFF.

Heat will come on when the

temperature falls below this

setpoint.

Select the cycles per

hour limit.

d=cycles per hour

limit defeated.

(d, 2 - 6)

Default = 6 cycles / hour

Default = 2 degrees

Default = 60 degrees

Adjust the deadband

from 1 - 6 degrees F.

Deadband is the difference

between Room temperature

& setpoint before the

equipment will turn on.

This step only appears in compressor equipped systems.

CYCLES/HOUR

DEADBAND

OFF MIN SETPOINT

Note: Set the thermostat to ‘OFF’ mode before adjusting settings.

Continued

Page 6

TO SET PRESS, OR

The purpose of d1 is to allow the installing technician

to override the thermostats 5 minute compressor lockout.

After installation is complete this setting should be set between

d and 6 cycles per hour.

This feature prevents rooms from getting to hot or too cold

when heating or cooling is turned off.

Advanced Setup II (continued)

Page 7

INSTALLATION

Press

To exit setup

screens:

F / C

Continued from prior page.

Press

FAN

Default = 30 seconds

Adjust the length of time

the fan will continue to

run after the temperature

is satisfied. (To purge

the system)

(0-90 seconds, in 15

second increments)

FAN PURGE

TO SET PRESS, OR

Select the type of equipment

this thermostat is connected

to, from the table on the

next page.

EQUIPMENT TYPE #

TO SET PRESS, OR

Adjust the maximum

temperature setpoint

that is used when the

thermostat indicates OFF.

Cooling will come on when

the temperature rises

above this setpoint.

Default = 85 degrees

OFF MAX SETPOINT

TO SET PRESS, OR

Press

FAN

This feature prevents rooms from getting to hot or too cold

when heating or cooling is turned off.

Advanced Setup

Page 8

Select the type of equipment this thermostat is connected

to, from the table above.

INSTALLATION

Equipment Setup Table

4 pipe fan coil, 3 speed fan

1 stage PTAC, 2nd stage strip heat, 1 speed fan, B reversing valve

1 stage PTAC, 2nd stage strip heat, 2 speed fan, B reversing valve

1 stage PTAC, 1 speed fan, B reversing valve

1 stage PTAC, 2 speed fan, B reversing valve

1 stage PTAC, 3 speed fan, B reversing valve

1 stage PTAC, 1 speed fan, O reversing valve

1 stage PTAC, 2 speed fan, O reversing valve

1 stage PTAC, 3 speed fan, O reversing valve

1 stage PTAC, 2nd stage strip heat, 1 speed fan, O reversing valve

1 stage PTAC, 2nd stage strip heat, 2 speed fan, O reversing valve

A/C, strip heater, 1 speed fan

A/C, strip heater, 2 speed fan

A/C, strip heater, 3 speed fan

A/C, gas, 1 speed fan

4 pipe fan coil, 1 speed fan

4 pipe fan coil, 2 speed fan

2 pipe fan coil, 1 speed fan, H2O changeover sensor required

2 pipe fan coil, 2 speed fan, H2O changeover sensor required

2 pipe fan coil, 3 speed fan, H2O changeover sensor required

Climate Master with a CXM Control Board

Climate Master with a DXM Control Board

2 pipe fan coil, 3 speed fan, IEC

4 pipe fan coil, 3 speed fan, IEC

2 pipe fan coil, 1 speed fan, part-time auxillary heat

2 pipe fan coil, 2 speed fan, part-time auxillary heat

2 pipe fan coil, 3 speed fan, part-time auxillary heat

2 pipe fan coil, 1 speed fan, part-time auxillary heat, IEC

2 pipe fan coil, 2 speed fan, part-time auxillary heat, IEC

2 pipe fan coil, 3 speed fan, part-time auxillary heat, IEC

Carrier PTAC, 1 speed fan, B reversing valve, Special

4 pipe fan coil modified to a 2 stage heat or cool only, 3 speed fan

About Advanced Features & Operation

Page 9

DIAGNOSTIC MODE - Press and hold the F / C button for

5 seconds to enter diagnostic mode. Once active, the

main display will alternately show the setpoint and then

the room temperature for 2 second intervals.

Exit the diagnostic mode by pressing F / C again or

turning the thermostat off.

FACTORY DEFAULTS - If, for any reason it is desirable to

return all stored settings back to the factory default

settings, press the Fan button. While holding the Fan

button in, press the Down button for 2 sec. All icons will

appear. Press and hold in the F / C button until Fd

appears. This resets all factory settings, except for the

equipment type.

TO CALIBRATE

At this point use the Up and Down buttons to calibrate

room temperature, if needed. Press the Fan button to

return to normal operation.

ROOM TEMPERATURE - To calibrate the

room temperature display, press and hold the Fan button.

While holding the fan button in, press and hold in the

Down button for 2 seconds. All icons will appear on the

display. Release the Fan button. Press the Fan button

once more.

Altri manuali per P/N 33CSSN2-MH

Indice

Altri manuali Carrier Termostato

Carrier

Carrier Performance TP-PRH-A Manuale utente

Carrier

Carrier TSTAT Istruzioni e ricette

Carrier

Carrier EDGE Pro Manuale utente

Carrier

Carrier Performance Edger Thermidistat Control... Manuale utente

Carrier

Carrier Aquazone 50QE900-NPWS Manuale utente

Carrier

Carrier 33CS420-01 Manuale utente

Carrier

Carrier N-MC-FC Manuale operativo

Carrier

Carrier PERFORMANCETSERIES EDGER THERMIDISTATT CONTROL... Manuale utente

Carrier

Carrier Performance EDGE Manuale utente

Carrier

Carrier 52M Performance Series Manuale utente

Carrier

Carrier edge TP-NHP01-A Manuale utente

Carrier

Carrier KAAFT0101AAA Manuale utente

Carrier

Carrier 33CS Istruzioni e ricette

Carrier

Carrier SUI Manuale utente

Carrier

Carrier 33CS Manuale

Carrier

Carrier TSTAT CC PS701 Manuale utente

Carrier

Carrier EDGE Pro 33CS2PPRH-03 Manuale utente

Carrier

Carrier Comfort Pro 33CSCNACHP-01 Manuale utente

Carrier

Carrier 33AW-CS1 Manuale utente

Carrier

Carrier AQUAZONE 50QE900-250FS Manuale utente

Carrier

Carrier TCSNAC01-A Manuale utente

Carrier

Carrier TSTATCCPB101 Manuale utente

Carrier

Carrier A07048 Manuale utente

Carrier

Carrier TP-WEM01 Manuale utente

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente

Honeywell

Honeywell T6811 Manuale utente