Cellinx CamPilot MR902 Manuale utente
1
2ch. Network Video Transmitter
CamPilot MR902
User Manual
CamPilot MR902
•2ch H.264 Video Encoder
•NTSC / PAL support
•Video : 2ch Input
•Audio : 2ch Input / 1ch Output
•D1 resolution at 30fps for each channel
•Multi-codec video support : H.264 / MJPEG
•Multi-stream with variable resolution & frame
- 1st stream : H.264 or MJPEG @ all resolutions
- 2nd stream : H.264 or MJPEG @ max. CIF
•Stream based motion detection
•VBR / CBR support
•Two-way audio supported (Full Duplex)
•Multi-codec audio support : G.711 / G.726
•RS-422/485 for external device control
•RS-232 for external device control
•2ch Digital Input / Output
•Power : DC 12V, 1A
Before installing and using the product,
please read this manual carefully.
Be sure to keep it handy for later reference.
Overview
Accessories
An adaptor and a LAN cable are not included in the product
2
Precaution
WARNING
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTIONS
■ Do not open or modify
Do not open the case, as it may be dangerous and cause damages.
■ Do not put objects inside the unit
Make sure that no metal objects or flammable substances get inside the camera. It could cause
fire, short-circuits or damages.
■ Be careful when handling the unit.
To prevent damage, do not drop the camera or subject it to strong shock or vibration.
■ Install away from electric or magnetic fields.
■ Protect from humidity, dust and high temperature.
An additional case that is temperature-controllable, damp-proof and waterproof is required for
outdoor use.
■ Cleaning
Dirt can be removed from the case only by wiping it with a soft cloth moistened with a soft
detergent solution.
■ Mounting Surface
The mounting surface material must be strong enough to support the camera.
■ CamPilot MR902 can be used for surveillance purpose.
Be thoroughly informed of related regulations prior to installation to ensure compliance with such
regulations
3
Overview
Features
CamPilot MR902 is a Network Video Server that transmits real-time high-resolution digital
video and audio data with H.264 high compression rate over Internet or Intranet.
Appearance
7. RESET (factory default button, push for 5
seconds when the power is supplied.)
8. Audio CH1 (Input, Ø 3.5 stereo jack)
9. Audio CH2 (Input, Ø 3.5 stereo jack)
10. Audio OUT (Output, Ø 3.5 stereo jack)
11. Video CH1 (Input, BNC Connector)
12. Video CH2 (Input, BNC Connector)
13. 10/100 Base-T LAN (Network, PoE (IEEE
802.3af) can be used)
14. Power LED
15. POWER (12V 1000mA)
▶Front
▶Top
▶Side
▶Rear
< 8 Pin
Connector
>
< 4 Pin Connector >
1. RS232C (external device control)
2. DI CH1/CH2 (Digital Input)
3. DO CH1/CH2 (Digital Output)
4. RS422 Tx(RS485) / Rx (external device control)
5. SD CARD LED
6. SD / SDHC CARD slot
4
Specification
Dimension
Specifications
Compression Type H.264(MPEG4 AVC) Baseline@L3.0 / MJPEG
Video Input 2ch
Resolutions D1 / 4CIF / VGA / CIF / QVGA / QCIF
Bitrate 32Kbps ~ 6Mbps
Frame Rate 30/25 (NTSC/PAL) fps @ all resolutions for each channel
Streaming H.264 Dual Stream or Simultaneous H.264 and MJPEG
Bi-Directional Audio Two way, full duplex (Stereo)
Audio Input Compression G.711 / G.726
Audio Line Input 2ch, Line lev el input. Nominal 0-dB input lev el is 1.0 VRMS. Gain of –34.5 dB to 12 dB.
Audio Output Compression G.711 / G.726
Audio Line Output 1ch, Line level output. Nominal output level 1.0 VRMS.
RS232 RS232C Level
Digital Input 2ch. (Dry Contact N.O. / N.C.)
Digital Output 2ch. (Relay Switching - Nominal Voltage 5VDC, 1A)
RS422 1ch. for external devices control (PTZ driver etc.)
SD Card SD/SDHC card interface support
Factory Default Button Restore to default setting (Network, Password and etc)
SD Card LED SD card status Indicator
LAN LED LAN status Indicator
Power LED Power status Indicator
Ethernet Ethernet(10/100 Based-T), RJ-45 Connector
Protocol
TCP, IP, HTTP, DHCP, FTP, DNS, DDNS, NTP, ICMP,
SNMP, SMTPE, UPnP, RTP, RTSP, Onvif
Web Browser IE 8.0 or above
SDK Cellinx SDK 4.0
Security MD5 Password / iptables (firewall)
Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F
Power Requirement DC 12V / 1.0A
Power Consumption 300mA (Nominal)
Dimensions 169(W) x 117(D) x 31(H) mm
Weight 345g
Case Material Aluminum
Network
Software
Power
Physical
Items
Video Compression
Audio Streaming
External I/O
▶Top
▶Section
▶Side
5
Connection
Basic connection
(1) DC 12V 1A (Power, When the PoE is used, the power connection is not necessary.)
(2) ETHERNET - LAN cable (RJ45 jack), the product is connected to PC or network equipment
such as HUB by the LAN cable. Please, refer to the standard of “IEEE 802.3af” for PoE
connection.
(3) VIDEO –video signal input (coaxial cable, BNC jack)
Expert connection
(1) DI (Digital Input): sensor, no polarity (N.O / N.C are all available.)
(2) DO (Digital Output): alarm, relay switch (nominal voltage 5VDC, 1A)
(3) RS422 (RS485): external device control (PTZ drive etc.)
(4) AUDIO IN / OUT
- IN: microphone, line level input (RCA jack, an amplified microphone should be used.)
- OUT: speaker, line level output (RCA jack, 8Ω)
An example of the relay device that is connected on “DO (Digital Output)”
▶Connection (when PoE is used.)
Manufacturer: SUNWOO /
Model: SW LY2N
▶Relay device
6
INTERNET
or
INTRANET
Connection
REF Monitoring PC Requirements
Item
Specification
Monitoring
PC
Processor
Pentium Core2 Duo or more
RAM
2GB or more
Graphic Card
512MB or more
OS
Windows 2003 / XP / Vista / 7
Monitor Resolution
1024 X 768 pixels or more
Network
10/100 Base-T LAN
Analog Camera
HUB
Configuration
Monitoring PC
Monitoring PC
Local Network
Public Network
LAN Cable
Router
PTZ Camera
MR902
MR902
7
Network
Setting an IP address
Change the network setting value with the program “NVTManagement”
1. NVTManagement execution
- Execute the file “NVTManagement.exe”
2. Setting an IP address
NVT (Network Video Transmitter) search
- Discovery button: searches the NVTs on the local network
NVT set-up
- The network information of the NVTs should be set by the rule of the local network information
- Select an NVT and change the information on “Network setting”and click “Apply”button after
change.
- Authentication: ID/Password –root/pass (Initial Value)
Additional function
- Clear: deletes the items that are searched on the list.
- Monitoring: selecting an NVT (activation) >> clicking the right mouse button >> clicking
“Monitoring”
- Checking the Serial No. and Firmware Ver. of an NVT on “NVT Information”
- Ping: executing the ping command for the searched NVTs.
8
Network
3. Accessing to CamPilot MR902 with a web browser
Open a web browser on a monitoring PC and enter the IP address assigned to a CamPilot
MR902 as following
Example> http://192.168.1.2
• The page as below shows up after the connection is completed.
ID / Password :
root / pass (Initial Value)
Login button :
it enables you to move to the Web
Monitoring Page. On checking the
Setting box and clicking the button, you
can move to the Web Setting Page.
Guest Login :
you can move to the Web Monitoring
Page as “guest”
Refer to the document “MR902_Web_Manual.pdf” for the Web server.
< 초기 접속화면 >
< 영상 모니터링>
▶The Initial Page
▶Web Monitoring Page
Indice
Altri manuali Cellinx Trasmettitore
