Certa CTINV35GENA Manuale utente

Warnings

Please pay attention to the following warnings when you see them in this manual.

WARNING: Indicates a strong possibility of severe personal injury or death if

instructions are not followed.

CAUTION: Indicates a strong possibility of severe personal injury or death if

instructions are not followed. If a problem should arise, or if you have any

questions about the generator, please contact the Kogan customer support team.

CARE: The generator is designed to give safe and dependable service if

operated according to instructions. ead and understand the user manual before

operating the generator. Failure to do so may result in personal injury or

equipment damage.

Safety Instructions

WARNING: Exhaust contains poisonous carbon monoxide. Do not operate the

generator in a confined environment. Only use outdoors, away from open doors,

windows or vents.

WARNING: The muffler becomes extremely hot during operation, and remains

hot for a while after stopping the engine. Be careful not to touch the muffler

while it is hot. Let the engine cool before storing the generator indoors.

WARNING: The engine exhaust system will be heated during operation and will

remain hot immediately after stopping the engine. To prevent scalding, pay

attention to the warning labels on the generator.

CARE: Do not connect other cables to receptacles during use or use a special

jack as it may cause electric shock.

WARNING: Fuel is extremely flammable, and is even explosive under certain

conditions. efuel unit in a ventilated area with the engine stopped.

WARNING: Keep away from cigarettes, smoke and sparks when refuelling the

generator. Always refuel in a well ventilated location.

WARNING: Connecting the unit to a building electrical system as a standby

power source must be performed by a qualified electrician. The connection must

isolate the generator from utility power, and must comply with all applicable laws

and electrical codes. Improper connections to a building's electrical system can

allow electrical current from the generator to backfeed into the utility lines. Such

backfeed may electrocute utility company workers or others who contact lines

during a power outage, and the generator may explode or catch fire when utility

power is restored.

WARNING: To avoid accidents and equipment damage, check the generator

every time before starting the engine.

WARNING: Keep the generator at least 1 meter away from other equipment

during operation.

WARNING: Keep the generator horizontal when running. If the generator is

tilted, it may cause fuel spillage.

WARNING: Generator operators must be trained, must know how to stop the

generator quickly and understand the purpose and operation of all controllable

parts. Untrained operators must not be allowed to use the equipment.

WARNING: Keep children and pets away from operation area.

WARNING: Keep away from rotating parts during operation.

WARNING: Do not operate unit with wet hands.

WARNING: Do not operate the generator in rain or snow, or let it get wet.

CAUTION: Wipe up any spilled fuel at once.

Table of Contents

Warnings...................................................................................................................................................... 1

Safety Instructions.............................................................................................................................. 1

Product Layout........................................................................................................................................ 3

Unit Body............................................................................................................................................... 3

Control Panel........................................................................................................................................ 3

Smart Throttle..................................................................................................................................... 3

Safety Label Locations.................................................................................................................... 3

Pre-operation Checks...................................................................................................................... 4

Checking the Oil................................................................................................................................. 4

Checking the Fuel Level................................................................................................................. 4

Check the Air Cleaner...................................................................................................................... 5

LCD Display Layout.......................................................................................................................... 6

Attaching the wheels to the generator ..................................................................................7

Using the remote controller & emergency button..............................................................7

Using the Generator.............................................................................................................................. 8

Starting the Engine........................................................................................................................... 8

High Altitude Operation................................................................................................................. 9

Generator Use..................................................................................................................................... 9

AC Applications................................................................................................................................ 10

Output and Overload Indicators............................................................................................... 10

DC Applications................................................................................................................................ 12

Starting the Engine.......................................................................................................................... 13

Oil Alert System................................................................................................................................ 13

Stopping the Engine....................................................................................................................... 14

Maintenance............................................................................................................................................. 15

Maintenance Schedule................................................................................................................... 15

Changing Oil....................................................................................................................................... 15

Air Cleaner service........................................................................................................................... 17

Spark Plug Servicing....................................................................................................................... 17

Transporting and Storage.................................................................................................................. 18

Transporting the generator.......................................................................................................... 19

Before storing the unit for an extended period.................................................................19

Muffler Fire Net Service................................................................................................................. 19

Troubleshooting.................................................................................................................................... 20

Engine will not start....................................................................................................................... 20

Deficient AC Output........................................................................................................................ 21

Equipment connected to generator won't start................................................................21

There is no power in the DC electric outlet..........................................................................21

Specifications......................................................................................................................................... 22

Product dimensions........................................................................................................................ 22

Engine................................................................................................................................................... 22

Generator ........................................................................................................................................... 22

Product Layout

Unit ody

Control Panel

Smart Throttle

The engine speed is kept at idle automatically when an electrical appliance is

disconnected, and will return again to proper speed when an electrical appliance

is connected. This is designed to minimise fuel consumption during operation.

Safety Label Locations

These labels warn you of potential hazards that can cause serious injury. ead the

labels and safety notes and precautions described in the manual carefully.

Air Vent Knob

Fuel

Cap

Top Maintenance

Cover

Control

Panel

Starting Grip

Muffler

Cover Fuel Valve

Primer Bulb

Maintenance

Access

Overload Indicator

Light

Output Indicator

Light

Oil Alert Indicator Light

Eco Throttle Switch

Engine Switch

Socket

DC Circuit

Breaker

Grounding

Terminal

AC Socket

AC V

Socket

Avoid Fire

Label

Avoid Burns

Label

Parameter

Label

Ventilation

Label Primer Bulb

Label

EPA Label

Pre-operation Checks

•Be sure to check the generator is on a level surface with the engine

stopped.

•Check the engine oil level.

•Using 2-stroke engine oil could shorten the engine's service life. Use a

premium quality 4-stroke engine oil.

Checking the Oil

•Loosen the cover screw and remove the left side maintenance cover.

emove the oil filer cap, then wipe the dipstick with a rag. Check the oil

level by reinserting the dipstick into the filler hole without screwing it in.

•If the oil level is below the end of the dipstick, refill up to the top of the oil

filler neck.

Note: The Oil Alert System will automatically stop the engine before the oil level

falls below the safe limit, however to avoid the inconvenience of an unexpected

shut-down, it is still advisable to visually inspect the oil level regularly.

Checking the Fuel Level

•Turn the fuel cap lever to the “OFF” position before transporting.

•Use unleaded automotive fuel.

Note: DO NOT use any fuels containing alcohol. Fuel system damage or engine

performance problems resulting from the use of fuels that contain alcohol are not

covered by warranty.

Dipstick

Lowest oil

level allowed

•Never use an oil/petrol mixture or dirty fuel.

•Avoid getting dirt, dust or water in the fuel tank.

•After refuelling, tighten the fuel filler cap securely.

•Petrol is extremely flammable under certain conditions.

•efuel in a well-ventilated area with the engine stopped.

•Do not smoke or allow flames or sparks in the area where the engine is

refuelled or where petrol is stored.

•Do not overfill the fuel tank. After refuelling, make sure that the tank cap is

closed properly and securely.

•Be careful not to spill fuel when refilling. Spilled fuel or fuel vapours may

ignite. If any fuel is spilled, make sure the area is dry before starting the

engine.

•Avoid repeated or prolonged contact with skin, or the breathing of vapour.

•KEEP FUEL OUT OF EACH OF CHILD EN

Check the Air Cleaner

Check the air cleaner element to ensure it is clean and in good working condition.

1. Loosen the cover screw and remove the left side maintenance cover.

2. Press the latch tab on top of the air cleaner body, remove the air cleaner

cartridge, then check the element.

3. Clean and replace the element if necessary.

Never run the engine without the air cleaner. apid engine wear will result from

airborne contaminants such as dust and dirt being drawn through the carburettor

and into the engine.

It is normal for a little oil to appear under the air filter box if the generator is

running for a long period of time or if a lot of oil is in the engine. Wipe up excess

oil after each use and after stopping the generator.

Fuel Cap

Open

Air Cleaner

Cartridge

Air Cleaner

Case

Screws

Access Panel

Screws

Access Panel Air Cleaner

Element

LCD Display Layout

The LCD display will light up after the generator has started up, and will be

functioning after 3-5 seconds.

Running display instructions

•U : Voltage

Displays the current voltage (V). The XXX.X (V) format (one decimal).

•I : Current

Displays the current Current (A). The XX.X (A) format (one decimal).

•F : Frequency

Displays the current frequency (Hz). The XX.X (Hz) format (integer).

•P : Power

Displays the current Power (W). The format is XXXX.X (W) (integer).

•Oil : Fuel

Invalid

•Time : Running Time

Displays the total running time. The format is xxx: xx: xx (hr: m: sec)

Overload / Oil Sensor light

Overload

The LCD screen will display the current output when the

generator is running normally. When the generator is

overloaded or short circuited, the generator will not

supply power to appliances. The voltage, current and

frequency will display “0” and the power display will

show “OVE ”.

At this time, the generator is not automatically shut down.

Please manually shut the generator down and investigate the reason of the

overload.

Over

Oil Sensor

The oil sensor system is to prevent engine

damage due to not enough oil being in the

reservoir. The oil sensor light will light up in

red before the oil level is under the safe line

in the crankcase, while the oil system

shutdown of the generator is automatic.

Attaching the wheels to the generator

1. Fix the wheel to the axle.

2. Fix the washer onto the wheel axle.

3. Fix the dowel onto the axle.

Using the remote controller & emergency button

Note: the generator can be started by using the starting

key & remote control.

•Use the starting key, not the remote controller, to

stop the generator when the generator has been

started by the starter key.

•Use the remote controller, not the starting key, to

stop the generator when the generator has been

started by the remote control.

•The emergency stop button can be used to stop

the generator at all times, no matter which method

was used to start the generator.

Oil sensor

light

Axle

2 wheels,

2 washers,

2 dowels

Dowel

Washer

Wheels

Wheel

assembly

Fix dowel

on axle

emote

controller

Starting

key

Emergency

stop button

Stop

Start

Press button

twice to start

generator.

Generator

remote control

Starter key

Using the Generator

Starting the Engine

1. Before starting the engine, disconnect any load from the DC receptacle.

Turn the fuel cap lever fully clockwise to the ON position.

2. Set the fuel valve to the ON position.

3. Set the motor switch to the ON position.

4. Pull slightly on the start cord until you feel resistance, then yank hard and

swiftly.

•Do not let the start cord retract by itself, but instead guide it back by hand.

•Hold the carry handle firmly to prevent the generator from falling over

when you pull the start cord.

Note: A hot motor will not start if there is too much fuel in the cylinder. If this

happens, wait for five to ten minutes before trying again.

Fuel Cap

Lever

Turn the fuel

valve knob to

the ON position

Engine Switch

Once the engine has started, allow the engine to run continuously and warm up.

If the engine stops and will not restart, check the engine oil level before

troubleshooting in other areas.

Before using a device once it is connected, switch the ECO switch off.

High Altitude Operation

At high altitudes, the standard carburettor air/fuel mixture will be excessively rich.

Performance will decrease and fuel consumption will increase.

High altitude performance can be improved by installing a smaller diameter main

fuel jet in the carburettor and readjusting the slow tempo screws. If you always

operate the generator at altitudes higher than 1,500m (4,000 feet) above sea

level, have a specialist perform these carburettor modifications.

Even with suitable carburettor jetting, engine horsepower will decrease by

approximately 3.5% for each 300m (1,000 feet) increase in altitude. The effect of

altitude on the horsepower will be greater than this if no carburettor modification

is made.

Note: Operation of the generator at an altitude lower than the carburettor is

jetted for may result in reduced performance, overheating and serious engine

damage caused by excessively lean air/fuel mixture.

Generator Use

•To prevent electric shock from faulty appliances, the generator should be

grounded. Connect an electric conductor (cable) of at least 1.5mm2

between the generator's ground terminal and an external ground source.

•Connections for standby power to a building's electrical system must be

made by a qualified electrician and must comply with all applicable laws

and electrical codes. Improper connections can allow electrical current

from the generator to feedback into the utility lines.

•Do not exceed the current limit set by any one receptacle.

•Do not connect the generator to a household circuit. This could cause

damage to either the generator, or to electrical appliances in the house.

•Do not modify or use the generator for any purpose other that what it is

intended for.

•Keep the generator away from other electrical cables or wires such as the

distribution network.

•The DC receptacle can be used while AC power is in use. If you use both at

once, ensure you do not exceed the total power for AC and DC.

•Most appliances require more than their rated wattage for start up.

Starting Grip

Altri manuali per CTINV35GENA

Manuali Generatore portatile popolari di altre marche

Kohler

Kohler 20EORZ Manuale di istruzioni

Powerhorse

Powerhorse 83171 Manuale utente

HURST

HURST ML-630-SI Manuale utente

ETQ

ETQ TG4000 Manuale utente

Briggs & Stratton

Briggs & Stratton 40265 Guida all'installazione

ConMed

ConMed 7550 Manuale utente

Owon

Owon Waveform Generator Manuale utente

evertz

evertz 7700 Series Manuale utente

Power Stroke

Power Stroke PS906025 Manuale utente

Firefly

Firefly Cygnus CYG2400/460/24 Manuale utente

Draper

Draper PG950S Aggiornamento firmware

PowerBoss

PowerBoss PowerBoss Manuale utente

SDMO

SDMO SH 4000 Manuale utente

EINHELL

EINHELL STE 5500 Manuale utente

Wanco

Wanco WI3000P Manuale utente

Full Boar

Full Boar FBT-3300 Manuale utente

Dwyer Instruments

Dwyer Instruments ASG Manuale utente

Westinghouse

Westinghouse WH1000i Series Manuale utente