CFE CFE-PVG1 Manuale utente
CFE-PVG1
User Manual
Document Version 01
Release Date 2023-06-27
Disclaimers
Before use, please read the user manual of this product to ensure that it
is used correctly when fully understood. After reading, please keep the
user's manual in a safe place for future reference. If you do not operate
this product properly, you may cause serious injury to yourself or others,
or cause damage to the product and property damage. By using this
product, you are deemed to have understood, acknowledged and
accepted the terms and content of this document in its entirety. Users
undertake to be responsible for their own actions and all consequences
arising therefrom. The company shall not be liable for all damages
caused by the user's failure to use the product in accordance with the
User Manual.
The Company has the final right to interpret this document and all
related documents of this product, subject to the laws and regulations.
Please pay attention to the official website for the latest product
information as it is subject to update, revision or termination without
notice.
1
Contents
Product Introduction ............................................................................................2
Characteristics......................................................................................................2
Panel display instruction..................................................................................... 3
Start and use..........................................................................................................4
Suggested Wire Diameter Of Connected Cable............................................ 8
Notice...................................................................................................................... 8
Product Specification.........................................................................................10
Transportation & Storage...................................................................................11
2
Product Introduction
The product is designed for power supply of net system.it uses digital
design idea,intelligent sine wave output and adapts to all kinds of
loads ;The design of excellent output short-circuit protection which can
resist impact of large current starting loads.The design of one-touch
intelligent switch for easy operation.It is widely used in household
electric equipment.Communication equipment.And single-phase power
equipment,industrial equipment,Ets.
Characteristics
MCU intelligent control，excellent performance
Adopt power frequency transformer, pure sine wave AC out put, strong
capacity of different loads
Excellent Design For Short-Circuit Protection, Work Reliably
Simple LCD display shows working status clearly
Intelligent charge control can extend the life span of the battery
Full-Oriented Protection, Safe And Reliable
Adapt to wide range of temperature and high altitude
3
Panel display instruction
Panel function introduction
Product function introduction
4
Start and use
Operation Steps
Step One
1.Connect the loads, battery and AC, switch the power
button(ON),enter into the first page as above photo.
2.All English operation display, can intuitive inverter all running state and
alarm state;
3.The first button is "return" second button is "turn up", the third button
is "turn down", the forth button is "confirm the current setting
parameter / or keep 3 seconds will enter into setting mode".
Step Two
1.Press "turn down "button, enter into the page as second photo;
2.page shows: PV voltage, charging current, generation power, gross
generation, MPPT module(status, temperature, output voltage ).
Step Three
5
1.Press "turn down "button, enter into the page as third photo;
2.Page shows: AC input voltage, inverter output voltage, battery voltage,
battery types, output frequency, loads percentage and inverter running
temperature.
Step Four:
1.Press "DOWN" button , enter into the setting page as fourth photo;
2.This page shows: setting AC output voltage, frequency, AC input
range and recover to battery discharge delay time.
Step Five:
1.Press "DOWN" button, enter into the setting page as fifth photo;
6
2.This page shows: setting AC charging current , MPPT charging current,
backlight, priority mode and ECO mode.
Set Operation
Step One:
1.Press "ENTER" button and keep 3 seconds, enter into the page as first
photo;
2.AC charging types:five types can be adjustable(can switch off AC
charging);
3.PV charging types: six types can be adjustable, can switch off PV
charging (only the hybrid inverter with controller);
4.Backlight setting: Normal/ ON can be adjustable;
5.Priority mode :ON/OFF can be adjustable;
6.ECO mode: ON/OFF can be adjustable.
Step Two:
1.Press "ENTER" and "ESC" buttons, enter into the setting page as
7
second photo;
2.Output voltage: 200V/210V/220V/230V/240V can be adjustable;
3.Output frequency: 50Hz/60Hz can be adjustable;
4.AC input range: narrow 160VAC-260VAC/ wide 130VAC-280VAC can
be adjustable;
5.AC transfer to battery time:10mins/30mins/60mins/120mins can be
adjustable;
6.Adjust battery parameter setting.
8
Suggested Wire Diameter Of Connected
Cable
Wire Diameter Of Cable （mm ）=Single Circuit Rated Current （A）
/(6A/mm )
1）PVC insulated copper core wire（@70℃）.
2）Temperature is lower than 40℃.
3）If the above conditions can not be reached, please use
strong cables.
Notice
Warm:installation should be executed by qualified technicians
according to the local related safety standard.
This product is suitable for the solar modules with same voltage grade
and power to charge battery.
Do not allow terminal solar input to connect with other types of charge
power, or else the controller will be damaged.
The top and surrounding of the controller should have 2.5CM space for
air circulation.
DC output does not allow access to motor type loads, and load current
is less than rated current.
Solar components connection: press the"SOLAR SWITCH"of rear panel
then the "BATTERY"lamp is lighting,The voltage and power of solar
Indice
Altri manuali CFE Pacco batterie
