Challenger AP11LCD Manuale utente

AP11LCD / AP11LED Manager Guide

AP11LED/LCD-Manager- Rev 02

Manager Guide

This User Guide tells you how to operate your intruder alarm system. To simplify this User

Guide we have assumed that the alarm system has been installed by a professional intruder alarm

system installer (the installer), and that the system is operating in a “typical” way. Aspects of

your system that are not “typical” will be described by your installer.

NOTE: If you have any questions about your intruder alarm system, then consult your installer,

see contact details at the front of this User Guide.

Indications on the system

Indications

LED steady on indication

LED flashing indication

LED off

Internal Sound

External Device: Strobe

External Siren: Bell

Using System

After you have finish system settings, you can use the system now. This section gives an

operation instructions how to set and unset the system as well as how to reset after an alarm.

AP11LCD / AP11LED Manager Guide

AP11LED/LCD-Manager- Rev 02

Table of Contents

Manager Guide................................................................................................................ 1

Indications on the system.............................................................................................. 1

Using System.................................................................................................................. 1

Table of Contents ........................................................................................................... 2

LED Keypad .................................................................................................................... 3

How to Set the System ................................................................................................................. 3

How to OMIT a zone(s) ............................................................................................................... 4

Unsetting the System ................................................................................................................... 4

How to UNSET from Alarm and RESET the system .................................................................. 5

How to use Panic Alarm on keypad............................................................................................. 5

How to Set up the system............................................................................................................. 6

How to go into Manager Program Mode ..................................................................................... 6

1 = Setup Codes ........................................................................................................................... 6

2 = View Event Log..................................................................................................................... 8

3 = How to Authorize engineer access......................................................................................... 9

4 = How to set Chime Zone ....................................................................................................... 10

6 = How to Setup Set Time........................................................................................................ 10

7 = How to Setup Set Date......................................................................................................... 10

8= How to Show Help file ......................................................................................................... 10

9 = Test System.......................................................................................................................... 11

How to Exit Manager Program Menu........................................................................................ 12

LCD Keypad ...................................................................................................................13

How to Set the System ............................................................................................................... 13

How to OMIT a zone(s) ............................................................................................................. 14

Unsetting the System ................................................................................................................. 15

How to UNSET from Alarm and RESET the system ................................................................ 15

How to use Panic Alarm on keypad........................................................................................... 16

How to Set up the system........................................................................................................... 16

How to go into Manager Program Mode ................................................................................... 16

1 = Setup Codes ......................................................................................................................... 17

2 = View Event Log................................................................................................................... 20

3 = How to Authorize engineer access....................................................................................... 21

4 = How to set Chime Zone ....................................................................................................... 21

6 = How to Setup Set Time........................................................................................................ 22

7 = How to Setup Set Date......................................................................................................... 22

8= How to Show Help file ......................................................................................................... 23

9 = Test System.......................................................................................................................... 25

How to Exit Manager Program Menu........................................................................................ 27

AP11LCD / AP11LED Manager Guide

AP11LED/LCD-Manager- Rev 02

LED Keypad

How to Set the System

Full Set

When you leave your premises you will need to set the intruder alarm system.

Before setting the system you should ensure that the premises have been completely vacated and

that all doors and windows are closed. Ensure that pets do not have access to the protected areas

as they can cause a false alarm.

Part Set

If your installer has programmed your system for PART SET operation you will be able to set

some zones of the system while others remain unset. Part set operation is often used at night time,

and it will permit you to free walk around the bedrooms while the living are and outside doors

are protected. Your system may have 2 part-set programs called Part 1 and Part 2.

Before Part-setting the system you should ensure that all doors and windows are closed. Ensure

that pets do not have access to the protected areas. Your installer may have instructed you to use

a different keypad to the one normally used to set the system.

Note:

There will be no exit beeps if Silent Exit mode was programmed.

You should wait until you hear that the exit beep has stopped before assuming that the

system has set.

LED Remote Keypad :

System is in Day mode

Enter User code/Manager code

Day LED will flash 5 second, then you can

select arm mode.

Press key to select Full arm mode,

Or press key to select Part 1 arm mode,

Or press key to select Part 2 arm mode.

Or press key to exit.

··

If the system has faults, you can see the fault

from the LED’s and the fault tone will be generated.

These faults will need to be cleared before the system

can be set

Press key quick set the system.(Optional)

Day

TAMP

Day

TAMP

Day

TAMP

Count down beep

R ES TE

Day

TAMP

Exit error beep

O IMT

AP11LCD / AP11LED Manager Guide

AP11LED/LCD-Manager- Rev 02

Day LED extinguish when armed

How to OMIT a zone(s)

If you cannot set the alarm system because a detector is faulty and in constant alarm you may

need to omit zones from the alarm system. A zone which has been omitted cannot cause an alarm.

Omitted zones will be restored after the system is unset.

Before a zone can be omitted it has to be enabled by the engineer as “Setup zone attrs/Omit

Allowed” zone.

LED Remote Keypad :

Set the system either Full/Part1 or Part2 (for more

information see “How to Setting the System”)

Press key to go into omit zone window,

and all omit allowed zone is lit.

e.g. To omit zone 4

Press to omit zone 4, the corresponding LED OFF.

Press same key to toggle ON/OFF.

Note: 1-9 key= zone1 –zone 9, 0 key = zone 10.

Press key to accept and continue setting

or press key to cancel omit function.

··

System will now set.

Unsetting the System

When you enter your premises you will need to unset (turn off) the system.

LED Remote Keypad :

System is in Set mode.

Enter User code/Manager code

System returns to Day mode.

CAUTION: Entering an invalid user code will operate the code tamper. After 9 incorrect keys

pushes a full alarm condition will be generated.

Day

TAMP

Day

TAMP

Day

TAMP

Day

TAMP

P OR G

R ES TE

Day

TAMP

Day

TAMP

O IMT

Day

TAMP

Day

TAMP

AP11LCD / AP11LED Manager Guide

AP11LED/LCD-Manager- Rev 02

How to UNSET from Alarm and RESET the system

You can unset the system in SET and reset it after an alarm, Tamper or PA.

The system will be programmed to be reset by the user or engineer. This is dependent on System

flags set up. See Engineer mode / Setup System/ Flags 1.

e.g. Zone 3 trigger alarm

LED Remote Keypad :

System is in Set mode.

Enter User code/Manager code

It will stop sound in alarm and the LED keypad will

show alarm event. First event is flashing, other lit.

Enter User code/Manager code

System returns to Day mode.

How to use Panic Alarm on keypad

Should you need to attract attention, the full alarm signal can be activated at emergency by

pressing 0 and 5 together

Press & simultaneously, the system and external sounder will sound immediately.

Note:

The engineer will need to programme this option for it to work.

Day

TAMP

Day

TAMP

Day

TAMP

AP11LCD / AP11LED Manager Guide

AP11LED/LCD-Manager- Rev 02

How to Set up the system

The full menu structure for the panel can only be accessed while in Manager Program Mode. The

structure is shown in the following table:

Note: LED Remote keypad Set Chime Zone.

How to go into Manager Program Mode

LCD Remote Keypad:

System work in Day mode

Go into Manager Menu.

Press

1 = Setup Codes

There are 2 user codes can be set by LED Keypad in the system. All are 4-digit and can be set to

any number from 0000 to 9999. The access codes ensure that only authorized users can operate

the system.

6=Manager’s Code 1 = user 1, 2 = user 2, 3 = Holiday,

Managers Code Default - 0123

Default User Codes – None Programmed

Managers Code:

The Managers Code (default 0123) can change all codes and has full access to the option

in the user programming mode.

Note: The Managers Code can only be changed from the User Programming Menu.

MENU OPTIONS

1 Setup Codes 6 Set Time

2 View alarm Log 7 Set Date

3 Authorize Engineer 8 Show Help File

4 Set Chime Zone 9 Test System

Day

TAMP

P OR G

0 1 2 3

Day

TAMP

AP11LCD / AP11LED Manager Guide

AP11LED/LCD-Manager- Rev 02

User 1 – User 2 codes:

The user 1 –user 2 codes have the same operation for testing and Setting and Unsetting,

changing their own code.

Holiday code:

The purpose of this code is to allow access to the property whilst the manager is absent. The

Holiday access code is programmed by the Manager and is only valid until the manager uses

the system. At this point the Holiday code becomes invalid and is no longer accepted by the

control panel.

NOTE:

Entering an invalid user code will operate the code tamper. After 9incorrect

key-push a full alarm condition will be generated.

How to change User Name

LED Remote Keypad:

The LED Remote Keypad cannot program user names.

How to change User Code

This option allows each of the users to be given a code.

LED Remote Keypad:

Under Manager Menu.

Press to select Setup User codes.

Press to change User 1.

Enter the new user 1 code (4 digits)

Press key to save. If the 4-digit is the same

as old, the error tone will be generated.

Press key will cancel and return.

Day

TAMP

Day

TAMP

New code

R ES TE

P OR G

Day

TAMP

Day

TAMP

AP11LCD / AP11LED Manager Guide

AP11LED/LCD-Manager- Rev 02

How to delete User Code

LED Remote Keypad:

Under Manager Menu.

Press to select Setup User codes.

Press to change User 1.

Press key to delete user 1 code.

Press to return to manager menu.

2 = View Event Log

The event log gives a display of all the events that have taken place. The events are arranged by

date and time. Up to 16 events can be stored in the memory. When the log reaches 16 events and

another event takes place, the first event drops out. The system is known as FILO (First In Last

Out).

To view the event log:

Led Remote Keypad:

Press: Jump to oldest event

Move one event older

Move one event newer

Jump to newest event

Clear all alarm event

After selecting Alarm Log the zone, PA and Tamper LED’s will show the latest event

A flashing LED indicates the zone that was first activated.

Any other LED lit was activated after the first event but before system unset.

Under Manager Menu.

Press key to select view alarm event.

LED 1flashing indicate Zone 1 is triggered first.

TAMPER is triggered after Zone 1

Day

TAMP

Day

TAMP

O IMT

Day

TAMP

Day

TAMP

R ES TE R ES TE

AP11LCD / AP11LED Manager Guide

AP11LED/LCD-Manager- Rev 02

Press to leave view alarm log menu.

How to clear all alarm events?

Under Manager Menu.

Press key to select view alarm event.

Press to clear all alarm events.

System all LEDs would be dark and emit

a confirm sound to indicate clear all alarm event.

Press to leave view alarm log menu.

Press to leave manager menu.

3 = How to Authorize engineer access

For the engineer to have access to the system the Manager will need to authorize Engineer access

to the control panel.

LED Remote Keypad:

Enter Manager program mode.

Press

Press to authorize Engineer access.

Then Engineer can access program mode

within 3hr hour.

Press to leave the current menu.

Day

TAMP

Day

TAMP

Day

TAMP

P OR G

0 1 2 3

R ES TE

Day

TAMP

Day

TAMP

Day

TAMP

Day

TAMP

Acknowledge

R ES TE

R ES TE R ES TE

AP11LCD / AP11LED Manager Guide

AP11LED/LCD-Manager- Rev 02

4 = How to set Chime Zone

If a Security Zone is programmed as Chime,you can hear special tone when it is triggered in

DAY mode.

Note: The zone must be set to security to be set.

LED Remote Keypad:

Under Manager mode

Press key go into Set Chime Zone function.

And zone 3 LED ON indicates the zone set chime.

e.g. Set Zone1, for Chime function.

Press key cannel zone 3 chime.

Press keys to select Chime zone.

Press to accept the change.

Or press to cancel.

6 = How to Setup Set Time

LED Remote Keypad:

The LED Remote Keypad cannot set time.

7 = How to Setup Set Date

LED Remote Keypad:

The LED Remote Keypad cannot set date.

8= How to Show Help file

LED Remote Keypad:

The LED Remote Keypad cannot operate the menu item.

Day

TAMP

P OR G

R ES TE

Day

TAMP

Day

TAMP

Day

TAMP

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Sistema di allarme popolari di altre marche

HOME8

HOME8 C13013US Manuale utente

Velleman

Velleman SG21000 Manuale utente