Chamberlain RIFMS2 Manuale utente

Carton Inventory

Overview

Assemble Intercom

Model RIFMS2

Wireless Flush Mount Intercom

Mounting Frame (2)

Intercom (2)

Fastener (8)

Screw (8)

Channel Button: Press the Channel button to set

intercom to one of four secure channels or the paging

channel. The default channel for the intercom is the

paging channel where all four channel lights are lit.

An intercom on a channel can only hear an intercom

on the same channel or on the paging channel.

Conference Mode: Conference

Mode allows multiple intercoms to

participate in a conversation

compared to Normal Mode in which

only two intercoms can communicate.

All intercoms must be set to the same channel or the

paging channel to be in Conference Mode. To place

intercoms in Conference Mode set Dipswitch #1 on

block 2 to the UP position.

Battery: When batteries are low intercom will emit

two beeps every ten minutes. Replace with

C batteries (not provided).

NOTE: To prevent damage to the circuit DO NOT use

C size Lithium batteries.

Operation & Features

Talk Button

Talk Button: To talk, hold

down the Talk button. All

intercoms in the network that

are on the same channel will

receive the signal. Release the Talk button when

done talking and within 10-15 seconds press and hold

the Talk button of a different intercom to make a

secure channel between the two. Once the channel is

made the other intercoms in the network cannot hear

the conversation.

Volume: Hold down the Talk button and press the

Channel button repeatedly to cycle through the

volume levels.

The Intercom has up to a 1000' range and allows

multiple simultaneous conversations, using a

900 Mhz secure digital radio link. The intercoms form

an exclusive network and respond only to other

intercoms in the network.

Channel Button Dipswitch Blocks

Block 1 Block 2

Install 4 C batteries (not

provided). Secure

batteries with fastening

strip. LEDs will light.

NOTES:

• Ensure that the batteries

are securely fastened or

they may fall out during

installation.

• To prevent damage to the circuit DO NOT use

C size Lithium batteries.

Channel Lights

Programming Intercom

Create New Network

The intercom must be programmed to at least one

other intercom to become a network or it can be

programmed into an existing network.

Press and hold both buttons on the intercom for

5 seconds. An initial beep will be heard followed by a

second beep. The channel lights will flash. Within 10

seconds put the second intercom into Learn Mode

(refer to table below).

Add to an Existing Network

Press and hold both buttons on the new intercom for

5 seconds. An initial beep will be heard followed by a

second beep. The channel lights will flash. Within 10

seconds put any networked intercom into Learn Mode

(refer to table below).

INTERCOM LEARN MODE

Press the Learn button until

a beep is heard.

Press and hold both buttons

for 5 seconds.

Each intercom will emit a tone when programmed into

network. Repeat for any additional intercoms.

INTERCOM LEARN MODE

Press the Learn button until

a beep is heard.

Press and hold both buttons

for 5 seconds.

Each intercom will emit a tone when programmed into

network. Repeat for any additional intercoms.

Step 4

Place intercom in frame by inserting top section first,

then snapping the lower section into place.

Step 3

Place the frame in the hole

and tighten screws.

NOTE: Place frame in wall so

that the two small slots are on

the top and the larger single

slot is on the bottom.

Step 2

Insert a screw into each

hole in the frame and attach

the fasteners. Tighten screw

only 1/4" into the fastener.

Step 1

Cut a hole in the wall measuring 6 1/8" wide by

4 1/2" high.

6 1/8"

4 1/2"

Choose mounting locations where both intercoms will

work when tested.

NOTES:

• The wall location should be clear of beams and

other obstructions inside the wall.

• Do not mount intercoms within 6' of each other.

• Do not mount intercom near any electrical wiring or

electrical devices.

Installation

FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:

1-800-528-9131

www.chamberlain-DIY.com

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this

receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.

THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Troubleshooting

Intercom does not function.

It is normal for LEDs to go out if intercom has been

inactive for 5 minutes. The LEDs should light after a

button is pressed or a signal is received.

Check batteries in Intercom.

Ensure intercom is connected to a network.

See Programming Intercom.

Ensure that intercoms are on the same channel. See

Operation & Features.

Intercom is not getting expected transmission

range.

Keep Intercom away from trees, metal objects and

electrical wiring.

Intercom beeps every ten minutes.

The battery is low in the intercom. Replace with

C batteries.

NOTE: To prevent damage to the circuit DO NOT use

C size Lithium batteries.

Need to clear intercom’s memory.

Press and hold both buttons. Two beeps will be heard

and the channel lights will begin to cycle. Continue to

hold until a third beep is heard (about 15 seconds).

Ensure other intercoms are not activated during this

time. Intercoms in the network that are on will signal

during the clearing process. Once memory is clear

the intercom can be programmed to a new network.

Static and feedback is heard in intercom.

The intercoms are too close to each other. A cordless

phone, cell phone, or other radio device can also

cause static.

Indice

Altri manuali Chamberlain Sistema di interfono

Chamberlain

Chamberlain RWIA Manuale utente

Chamberlain

Chamberlain RWIS Manuale utente

Chamberlain

Chamberlain TAC11 Istruzioni per il montaggio

Chamberlain

Chamberlain Elite EL Series Manuale del proprietario

Chamberlain

Chamberlain LiftMaster ELITE EL25 Manuale utente

Chamberlain

Chamberlain LiftMaster ELITE EL2000 Manuale utente

Chamberlain

Chamberlain GAILM Manuale utente

Chamberlain

Chamberlain NDIS Manuale utente

Chamberlain

Chamberlain LSIAC Manuale utente

Chamberlain

Chamberlain 75EV Manuale utente

Chamberlain

Chamberlain Icon26 series Manuale utente

Chamberlain

Chamberlain MyQ Business CAPXL Manuale utente

Chamberlain

Chamberlain LiftMaster ELITE EL25 Manuale utente

Chamberlain

Chamberlain LIFTMASTER MUGAPLM Manuale utente

Chamberlain

Chamberlain myQ Business CAPXM Manuale utente

Chamberlain

Chamberlain LiftMaster FDI Manuale utente

Chamberlain

Chamberlain LiftMaster 833-1LM Manuale utente

Chamberlain

Chamberlain ELITE EL2000LG Manuale del proprietario

Chamberlain

Chamberlain Smart Video Intercom M Manuale utente

Chamberlain

Chamberlain LiftMaster Professional RIFM1LM Manuale utente

Chamberlain

Chamberlain OPI Manuale utente

Chamberlain

Chamberlain LiftMaster ELITE EL25 Manuale utente

Chamberlain

Chamberlain WIRELESS GATE ACCESS RGAIPI Manuale utente

Chamberlain

Chamberlain EL1SS Guida utente

Manuali Sistema di interfono popolari di altre marche

Bticino

Bticino LINEA 3000 Manuale utente

MSI

MSI MSI-140 Manuale utente

golmar

golmar Stadio Plus Manuale utente

CyberData

CyberData 011211 series Manuale

Vidos

Vidos duo M1021 Manuale utente

Vimar

Vimar ELVOX 7539/E Manuale utente

SSS Siedle

SSS Siedle BTSV 850-03 Manuale utente

Dahua

Dahua VTO Series Manuale utente

Elvox

Elvox 5651 Manuale utente

Videx

Videx VIDEOKIT Series Manuale utente

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuale utente

Viking

Viking E-35-EWP Manuale utente

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuale utente

SSS Siedle

SSS Siedle BFCV 850 Series Manuale utente

GRD

GRD MAX V2 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Aiphone

Aiphone IE-8MD Manuale utente

Perel

Perel EDB4 Manuale utente