Chamberlain KLIK3U-BK2 Manuale utente
UNIVERSAL REMOTE CONTROL
The remote control can be programmed to activate
up to two products, such as a garage door opener,
gate operator, or commercial door operator. Each
button on the remote control works independently
of the other and must be programmed separately.
The images throughout this manual are for
reference only and your product may look different.
MODEL KLIK3U-BK2
MODEL KLIK3U-BL2
MODEL KLIK3U-SS
MODEL KLIK3U-RT1
MODEL KLIK3U-RT2
To prevent possible SERIOUS INJURY or
DEATH from a moving gate or door:
• ALWAYS keep remote controls out of reach
of children. NEVER permit children to
operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be
seen clearly, is properly adjusted and there
are no obstructions to door travel.
• ALWAYS keep gate or door in sight until
completely closed. NEVER permit anyone to
cross path of moving gate or door.
Read instructions thoroughly BEFORE
beginning. If using the Universal
Remote Control with residential door
openers, the remote control must be
used only with door openers
manufactured after 1993 that utilize photoelectric
sensors. The photoelectric sensors are always
located on or near the bottom of the door track.
STOP
GETTING STARTED
Determine if the product you are programming the
remote control to has a Program/LEARN button or
DIP SWITCHES. The Program/LEARN button or DIP
SWITCHES are located either on the product or in
an external receiver on or near the product. The
following instructions are for a garage door opener
with a Program/LEARN button. For DIP SWITCH
programming instructions or additional help please
visit www.chamberlain.com/klik3.
OR
Program/
LEARN Button
DIP Switch
WARNING: This product can expose you to
chemicals including lead, which are known
to the State of California to cause cancer
or birth defects or other reproductive
harm. For more information go to
www.P65Warnings.ca.gov
PROGRAMMING
Remove the cover. Press and hold the
program button until the LED turns on.
Program
Button
Press and release the Program/LEARN button
on your garage door opener.
LED
1
2
Select a button to program. Press and release
the button the specified number of times
according to the chart on the following page.
Make sure the LED stops flashing between
each press of the button. The garage door
opener will respond by clicking, blinking, or
activating.
3
Cover
PROGRAMMING (continued)
Garage Door
Opener Brand Type/Color
of Program/
Learn button
Year Number
of times
to press
button
Linear®Mega-Code ’97-Current 1
Chamberlain®* Orange/Red ’97-’03 2
Chamberlain®* Purple ’05-Current 3
Chamberlain®* Green ’93-’96 4
Genie® **
Overhead Door®Intellicode ’05-Current 5
Genie®
Overhead Door®Intellicode ’95-Current 6
Stanley®Secure Code ’98 7
Chamberlain®* Yellow ’11-Current 8
Wayne Dalton®Rolling Code ’99 9
Press the program button on the remote
control to save.
Program Button
4
*NOTE: LiftMaster, Do-It, Master Mechanic,
Raynor, True Value and Sears Craftsman are
compatible with Chamberlain technology.
**NOTE: Visit www.chamberlain.com/klik3 for
Genie Intellicode II instructions.
TEST
Test the remote control by pressing the button. If
the garage door opener does not activate, repeat
the programming steps or visit
www.chamberlain.com/klik3 for additional
instructions.
To prevent possible SERIOUS INJURY or
DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify
doctor.
To reduce risk of fire, explosion or chemical
burn:
• Replace ONLY with 3V CR2032 coin
batteries.
• DO NOT recharge, disassemble, heat above
212°F (100°C) or incinerate.
Dispose of batteries properly.
Replace ONLY with
3V CR2032 coin batteries.
Battery
BATTERY
NOTICE: To comply with FCC and or Industry Canada (IC)
rules, adjustment or modifications of this receiver and/or
transmitter are prohibited, except for changing the code
setting or replacing the battery. THERE ARE
NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR
OFFICE USE. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2)this device must accept any
interference received, including interference that may
cause undesired operation.
Need Help?
Go to www.chamberlain.com/klik3
or call 1-800-442-1255
All trade names used herein are trademarks of respective
manufacturers listed.
Altri manuali per KLIK3U-BK2
1
Indice
Altri manuali Chamberlain Telecomando
Chamberlain
Chamberlain 61LMC Manuale utente
Chamberlain
Chamberlain 753CB Manuale utente
Chamberlain
Chamberlain 4330E Manuale utente
Chamberlain
Chamberlain 312HMC Manuale utente
Chamberlain
Chamberlain LiftMaster Security+ 973-315LM Manuale utente
Chamberlain
Chamberlain 375LM Manuale utente
Chamberlain
Chamberlain LiftMaster 361LM Manuale utente
Chamberlain
Chamberlain KLIK5U-WP Manuale utente
Chamberlain
Chamberlain KLIK3C-BK2 Manuale utente
Chamberlain
Chamberlain Security+ 963CD Manuale utente
Chamberlain
Chamberlain 850CB Manuale utente
Chamberlain
Chamberlain LiftMaster 373P Manuale utente
Chamberlain
Chamberlain KLIK3U Manuale utente
Chamberlain
Chamberlain LiftMaster Professional 412HM Manuale utente
Chamberlain
Chamberlain Passport PPV3 Manuale utente
Chamberlain
Chamberlain 895MAX Manuale utente
Chamberlain
Chamberlain Clicker KLIK1U Manuale utente
Chamberlain
Chamberlain Security+ 963D Manuale utente
Chamberlain
Chamberlain 371LM Manuale utente
Chamberlain
Chamberlain LiftMaster 333LM Manuale utente
