Chamberlain TriCode Systems Manuale utente

TriCode LiftMaster Four Button Garage Door Opener Remote Control

Transmitter Coding Instructions

TC4 Four Channel Transmitter Coding Instructions

This device complies with FCC Rules Part 15 and IC Canada Rules and Regulations.

Operation is subject to the following two conditions: (1) This device may not cause harmful

interference and (2) this device must accept any interference received, including

interference that my cause undesired operation. F.C.C. rules prohibit adjustments to or

modification of receiver and/or remote control transmitter circuitry except for changing the

code setting and replacing remote control transmitter battery. THERE ARE NO OTHER

SERVICEABLE PARTS.

CAUTION

ACTIVATE THE TRANSMITTER ONLY WHEN THE DOOR/GATE IS IN FULL VIEW,

FREE OF OBSTRUCTION AND PROPERLY ADJUSTED. NO ONE SHOULD ENTER OR

LEAVE THE DOOR/GATE WHILE IN MOTION. DO NOT ALLOW CHILDREN TO

OPERATE THE REMOTE(S) OR THE DOOR/GATE CONTROL BUTTONS. DO NOT

ALLOW CHILDREN TO PLAY NEAR THE DOOR/GATE.

The TriCode™ digital TC4 transmitter is a four-channel wireless radio control designed for

use with automatic garage/gate operators and access control systems. All TriCode™

products can be used with Linear/Delta 3™, Stanley™ and Multi-Code™ receivers. Two

configuration switches allow the four buttons to be configured to interface with two different

receiver types in the same transmitter. The TriCode™ radio format provides a potential of

2048 different digital codes. Two 10-posistion DIP switches, each capable of 1024 different

digital codes provide these codes. For Delta-3™ products, 512 (256x2) different digitals

codes are available.

SWITCH SETTINGS

CAUTION: To avoid possibility of duplicating codes in adjacent systems, all

transmitters should be recoded prior to operation. Unless using the maximum

number of codes four codes should not be used:

All DIP Switches ON

All DIP Switches Off

DIP Switches alternating ON/OFF

DIP Switches alternating OFF/ON

STEP 1: LOCATE SWITCHES AND CONNECT BATTERY

Locate the DIP switches, configuration switches and battery by sliding down access cover on

front of the transmitter case. DIP switches are numbered 1 through 10. The configuration

switches are located to the right of the DIP switches. The battery is located below the

switches. Connect the battery connector to the 9V battery before programming transmitter

STEP 2: SET TRANSMITTER CONFIGURATION SWITCH(S)

The TriCode™ Transmitter is factory set to Linear/Delta-3™ position. Using a pointed object

set transmitter configuration switches to desired setting..

STEP 3: SET TRANSMITTER DIP SWITCH(S)

The TriCode™ Transmitter DIP switch(s) are factory set, CH1 OFF (1-10) and CH2 ON (1-

10).

Using a pointed object set transmitter DIP switches to desired setting. For Linear/Delta-3™

compatibility, set codes on switches 1 through 8. Switches 9 and 10 are not used for

Linear/Delta-3™ products.

Note: Switches in receiver must match the switches in all transmitters used to

operate the receiver. Some older radios use toggle switches and it may be difficult

to determine 'ON' & 'OFF'. If so, try reverse settings on the TriCode™.

STEP 4: RECODE RECEIVER CODES

Once the transmitter codes have been set, verify the receiver codes are set to the following

settings:

Linear/Delta-3™ Receiver Type Detail

When the TC4 is set to the Linear/Delta-3™ transmitter type, set the receiver DIP switches

as follows.

Receiver 1 - Set switch 1-8 to match switch 1, activates from Button 1.

Receiver 2 - Set switches 1 and 2 OFF, match switches 3-8 on switch 2, activates from

Button 2.

Receiver 3 - Set switch 1 ON, switch 2 OFF, match switches 3-8 on switch 2, activates from

Button 3.

Receiver 4 - Set switch 1 Off, switch 2 ON, match switches 3-8 on switch 2, activates from

Button 4.

Multi-Code™ Receiver Type Detail

When the TC4 is set to the Multi-Code™ transmitter type, set the receiver DIP switches as

follows.

Receiver 1 - Set switch 10 OFF, match switches 1-9 on switch 1, activates from Button 1.

Receiver 2 - Set switch 10 ON, match switches 1-9 on switch 1, activates from Button 2.

Receiver 3 - Set switch 10 OFF. match switches 1-9 on switch 2, activates from Button 3.

Receiver 4 - Set switch 10 ON, match switches 1-9 on switch 2, activates from Button 4.

Stanley™ Radio Receiver Type Detail

When the TC4 is set to the Stanley™ radio transmitter type, set the DIP switches as follows.

Receiver 1 - Set switch 10 OFF, match switches 1-9 on switch 1, activates from Button 1.

Receiver 2 - Set switch 10 ON, match switches 1-9 on switch 1, activates from Button 2.

Receiver 3 - Set switch 10 OFF, match switches 1-9 on switch 2, activates from Button 3.

Receiver 4 - Set the switch 10 ON, match switches 1-9 on code switch 2, activates from

Button 4.

NOTE: The DIP switches in the receiver must match the DIP switches in all transmitters

used to operate the receiver.

STEP 5: TEST THE EQUIPMENT

If not already installed, connect the receivers to the operators as described in their

installation instructions. Be sure the door/gate is clear of people and obstructions.

Activated each transmitter button and verify that each receiver triggers its operator.

Battery Replacement: The 9 volt battery should last 12 to 18 months of normal use. The

red LED on the face of the transmitter will light dimly or not at all when the battery needs

replacing. The battery is located under the access cover.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Chamberlain Telecomando

Chamberlain

Chamberlain 64LM Manuale utente

Chamberlain

Chamberlain LiftMaster Security+ 372LM Manuale utente

Chamberlain

Chamberlain PASSPORT CPT4 Manuale utente

Chamberlain

Chamberlain 312HMC Manuale utente

Chamberlain

Chamberlain LiftMaster Professional Security+ 974-315LM Manuale utente

Chamberlain

Chamberlain LiftMaster Security+ 327LM Manuale utente

Chamberlain

Chamberlain LiftMaster Professional 83LM Manuale utente

Chamberlain

Chamberlain LiftMaster Security+ 973LM Manuale utente

Chamberlain

Chamberlain Passport MAX PPV3M Manuale utente

Chamberlain

Chamberlain Security+ 963D Manuale utente

Chamberlain

Chamberlain CPTX Manuale utente

Chamberlain

Chamberlain LiftMaster 375LM Manuale utente

Chamberlain

Chamberlain TX2EV Manuale utente

Chamberlain

Chamberlain LiftMaster 373P Manuale utente

Chamberlain

Chamberlain LiftMaster Professional 82LM Manuale utente

Chamberlain

Chamberlain 972MOM Moore-o-Matic Manuale utente

Chamberlain

Chamberlain 4330EML Manuale utente

Chamberlain

Chamberlain LiftMaster 373W 315 MHz Security+ Manuale utente

Chamberlain

Chamberlain 956CB Manuale utente

Chamberlain

Chamberlain KLIK5U-WP Manuale utente

Chamberlain

Chamberlain 33LMC Manuale utente

Chamberlain

Chamberlain 892LT Manuale utente

Chamberlain

Chamberlain MC100AMLR Manuale utente

Chamberlain

Chamberlain 953EV Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione