Champsolution BL5302 Manuale utente

Outdoor Motorized Bullet Camera

Quick Installation Guide

8608586340020

Quick Installation Guide

Please follow the installation steps below to set up your Motorized Bullet IP Camera.

Check the package contents against the list below. See P.1

Physical overview. See P.2

I/O Terminal Block Circuit.See P.3

I/O Terminal Block Pin Definition.See P.3

LED Indicator Definition. See P.4

Power mode. See P.4

Install the hardware and connect all cables. See P.5

Microsoft OS: Use the software CD to install Camera Installation Tool.See P.8

Access the IP Camera using Camera Installation Tool.See P.8

Mac OS using Safari Broswer. See P.11

Lighting environment. See P.11

Change the Web Interface into your preferred language. See P.12

Package Contents

Camera Outdoor Motorized Bullet Camera

Quick Installation Guide Brief product information and quick installation

Accessory Sun shield and screws

Wall mount bracket

Metal plate for wall mount bracket

Screw pack for wall and ceiling mounting

Alignment sticker

Body adapter

Wrench for front & back cover

Waterproof Connector

Moisture Absorber

Foam tape

2 pin terminal blocks for power

Cat 5e Female Coupler

Software

The following software and information are available online:

-Camera Bundle Software

-Camera Installation Tool

-User manuals

Please go download fromhttp://www.champsolution.com/DownloadMainpage.php

Physical overview

－

Front

－

Warning:

The IR LED is classified as class 3B laser IR. It’s hazardous and harmful if the eye is

exposed directly. Please don’t look straight at the LEDs during operation.

－

Rear

－

Light Sensor

Lens

IR LED

SD card/ Network Link

status indicator

Video out

Reset

I/O Terminal Block:

1: Ground,

2: +12VDC,

3: Audio in,

4: Audio out,

5: Digital Output 1,

6: Digital Output 2,

7: Digital Input 1,

8: Digital Input 2,

9: RS-485+,

10: RS-485-

Power status indicator

NTSC/ PAL switch

SD card slot

DC 12V Power

Smart Focus control

I/O Terminal Block Circuit

I/O Terminal Block Pin Definition

PIN Definition Description Max. V/A

1 Ground -

2 + 12VDC 12V DC

1.2 W

3 Audio In Unbalanced, 1.4Vp-p, 1Vrms, terminal block -

4 Audio Out Unbalanced, 1.4Vp-p, 1Vrms, terminal block -

5 Digital Output 1

Uses an NPN transistor with the emitter

connected to the GND pin. If used with an

external relay, a diode must be connected in

parallel with the load for protection against

voltage transients.

100 mA

24V

6 Digital Output 2

Uses an NPN transistor with the emitter

connected to the GND pin. If used with an

external relay, a diode must be connected in

parallel with the load for protection against

voltage transients.

100 mA

24V

7 Digital Input 1

Connected to GND to activate, or leave

floating (or unconnected) to deactivate.

30V DC

8 Digital Input 2

Connected to GND to activate, or leave

floating (or unconnected) to deactivate.

30V DC

9 RS-485 + -

10 RS-485 - -

LED Indicator

LED Color Indication

Network Blue

Steady blue for Network link

Flash blue while Network activity

Power

Red Steady red for booting up process

Blue Steady blue for booting up completion

Unlit

when reset button pressed for at least 5 sec.

to factory default

SD Card Yellow Steady yellow means SD card ready

Flashes yellow while accessing SD card

Power Mode

PoE

Mode

Power

Requirement PoE (IEEE802.3at) with Class 4

Power

Consumption

3.3 W, without IR/ Heater/ Fan

11.4 W, with max. IR on

12.8 W, with max. IR and Fan on

7.9 W, with max. Heater and Fan on

4.7 W, with max. Fan on

15.9 W, with max. IR/ Heater/ Fan

Power

Requirement PoE (IEEE802.3af) with Class 3

Note: While IR on, Heater and Fan will be disabled.

Power

Consumption 3.6 W, without IR/ Heater/ Fan

11.7 W, with max. IR on

Adaptor

Mode

Power

Requirement 12V/1.5A Adaptor

Power

Consumption

3.5 W, without IR/ Heater/ Fan

11.9 W, with max. IR on

13.2 W, with max. IR and Fan on

7.8 W, with max. Heater and Fan on

4.9 W, with max. Fan on

15.9 W, with max. IR/ Heater/ Fan

Note: Heater and Fan will be activated while the inner temparature drops under 5℃and

will be inactived while it above 10℃. Fan will be actived while the inner temparature above

50℃and will be inactived while it drops under 45℃.

Install the hardware and connect all cables

A. Hardware installation

a. Assembling sun shield and camera with two supplied screws (M5*6L).

Note: Please move the sun shield to secure the first screw on the fourth scale. (See figure

b. Use T25 wrench to loosen the back cover.

c. Take out the screw plug and change to M12 waterproof connector. Insert all cables

(power cord/ DIDO/ video out) into the connector.

d. Feed all cables to the back manual plate and connect them to the specific sockets then

secure waterproof connector tightly.

e. Attach the foam tape and moisture absorber on the back cover then secure the back

cover back. (Please change a new moisture absorber if open the front/ back covers

afterwards.)

f. Feed all cables through adapter and wall mount bracket if you use the supplied bracket,

or let the cable through out the hole on right side of adapter if you use standard bracket.

(Please see B. Two way bracket installing.) Then secure the screws (M3*12L) by

2.5mm Allen wrench.

Figure 1

B. Two ways bracket installation

a. Use the supplied bracke RJ45, power, DIDO, video out cables can be fed through the

supplied adapter and bracket with cable management protected installation. (See figure

b. Use standard bracket

Through our supplied adapter, there’s alternatived to use your selected standard

bracket. Cables will be passed through the right side hole of adapter. (See figure 2)

C. Connect Ground wire

Connect the ground wire to the IP camera’s adapter and secure with supplied ground

screw.

Figure 1

Figure 2

D. Wall mounting and Ceiling mounting

a. Attached the alignment sticker to the wall. Drill five holes into the wall, which four for screws and one

for cable. Then hammer the supplied plastic anchors into the screw holes and secure the mounting

plate by 5mm Allen wrench with supplied screws (T1/4”*32).

b. Hang the wall mount bracket on the mounting plate and fix it with the supplied screws.

c. Adjust the angle of the wall mount bracket by 6mm Allen wrench to aim the shooting area.

E. Connect all cables

a. Without Power over Ethernet (PoE) connection

1. Connect the power adaptor to the IP Camera.

2. Using a standard RJ-45 network cable,

connect the

IP Camera to a normal Hub/ Switch/ Router.

b. Power over Ethernet (PoE)

Using a standard RJ-45 network cable, connect the

IP Camera to a PoE-enabled Hub/ Switch/ Router.

Microsoft OS: Go Website download Camera Installation Tool

Please go http://www.champsolution.com/DownloadMainpage.php download “Camera

Installation Tool”. Andfollow the installation process to complete the installation.

Access the IP Camera using Camera Installation Tool

1. Please check two settings before using Camera Installation Tool

2. Click the Camera Installation Tool Icon on your desktop. The main page will show up

listing all active camera and video server devices. Select the relevant IP camera from

the list and double click to link to IE.

a. Browser’s Internet Properties → Security

→

Default Level

b. Browser’s Internet Properties → Privacy

→ Uncheck

Pop-up Blocker

4. When accessing the IP Camera for the first time, an information bar pops on the screen:

This website wants to install the following add-on: ‘AxvideoView.cab’.

3. Enter your Username and Password

to login to the IP Camera.

(Default is admin / admin)

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Telecamera IP popolari di altre marche

FLIR

FLIR Exx series Manuale utente

Avigilon

Avigilon H4A-BO1-IR Manuale utente

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuale utente

ShareTech

ShareTech AV1 Manuale utente

Ezviz

Ezviz C6C Manuale utente

Melchioni

Melchioni UCAM 2015 Manuale utente

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuale utente

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuale utente

Mitel

Mitel 6800i Series Manuale di servizio

Vitek

Vitek VTC-IR403-212NP Manuale utente

THOMSON

THOMSON DSC - 323W Manuale utente

AVer

AVer FB2027 Manuale utente

ENFORCER

ENFORCER EV-T5105-N2SQ Manuale utente

Wansview

Wansview NC543 Manuale utente

Eneo

Eneo MCB-64A0003M0A Manuale utente

deView electronics

deView electronics CBDNI36F Manuale utente

Swann

Swann SwannEye Manuale utente

LevelOne

LevelOne IP CamSecure Manuale utente