Chicago Electric 93431 Manuale utente

5” RANDOM ORBITAL

PALM SANDER

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit ourWeb site at http://www.harborfreight.com

portion of this manual or any artwork contained herein may be reproduced in

anyshapeorform withoutthe expresswrittenconsent ofHarbor FreightTools.

For technical questions and replacement parts, please call 1-800-444-3353.

TO PREVENT SERIOUS INJURY,

READ AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

93431

Due to continuing improvements, actual product may differ slightly from the product described herein.

Page 2SKU 93431 For technical questions, please call 1-800-444-3353.

SAVE THIS MANUAL

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in

electric shock,fire,and/or serious injury.

SAVE THESE INSTRUCTIONS

WORK AREA

1. Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents. Make sure there is adequate surrounding workspace.

2. Do not operate power tools in explosive atmospheres, such as in the presence

of flammable liquids,gases,or dust. Power tools create sparks which may ignite

the dust or fumes.

3. Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control. Protect others in the work area from

debris such as chips and sparks. Provide barriers or shields as needed.

E194601

SNOITACIFICEPSTCUDORP

stnemeriuqeRlacirtcelEspmA0.2,zH06,CAV021

deepS"23/3,)etuniMrePstibrO(MPO000,21 retemaiDtirbO

noitcelloCts

uDdedulcnIgaB

snoisnemiDdehcattagaBtsuD/wgnoL"9

gnikcaB/csiDgnidnaS daP "4/3-4;ngiseDpooL&kooH,eloH8"5 dedul

cnicsiDgnidnaSeceiP1;retemaiD )tirG08(

thgieW.sbL09.2

Youwillneedthismanualforthesafetywarningsandprecautions,assembly,operating,

inspection, maintenance and cleaning procedures, parts list and assembly diagram.

Keep your invoice with this manual. Write the invoice number on the inside of the

front cover. Keep this manual and invoice in a safe and dry place for future reference.

Page 3SKU 93431 For technical questions, please call 1-800-444-3353.

ELECTRICAL SAFETY

4. Groundedtools must be pluggedinto an outlet properlyinstalled and grounded

in accordance with all codes and ordinances. Never remove the grounding

prong or modify the plug in any way. Do not use any adapter plugs. Check

withaqualified electrician if youare in doubt astowhether the outlet isproperly

grounded. If the tools should electrically malfunction or break down, grounding

provides a low resistance path to carry electricity away from the user.

5. Double insulated tools are equipped with a polarized plug (one blade is wider

than the other). This plug will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a

qualified electrician to install a polarized outlet. Do not change the plug in any

way. Double insulation eliminates the need for the three wire grounded power

cord and grounded power supply system.

6. Avoid body contact with grounded surfaces such as pipes,radiators,ranges,

and refrigerators. There is an increased risk of electric shock if your body is

grounded.

7. Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

8. Do not abuse the Power Cord. Never use the Power Cord to carry the tools or

pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp

edges,ormovingparts. Replace damagedPower Cordsimmediately. Damaged

Power Cords increase the risk of electric shock.

9. When operating a power tool outside, use an outdoor extension cord marked

“W-A”or“W”. Theseextensioncordsare ratedforoutdooruse,and reducethe risk

of electric shock.

PERSONAL SAFETY

10. Stay alert. Watch what you are doing,and use common sense when operating

a power tool. Do not use a power tool while tired or under the influence of

drugs, alcohol, or medication. A moment of inattention while operating power

tools may result in serious personal injury.

11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair,clothing,and gloves away from moving parts. Loose clothes,jewelry,

or long hair can be caught in moving parts.

12. Avoid accidental starting. Be sure the Power Switch is off before plugging in.

Carrying power tools with your finger on the Power Switch, or plugging in power

tools with the Power Switch on, invites accidents.

13. Removeadjusting keys or wrenchesbefore turning the powertool on. Awrench

ora keythat is leftattachedto a rotating partof the powertool mayresult in personal

injury.

Page 4SKU 93431 For technical questions, please call 1-800-444-3353.

14. Do not overreach. Keep proper footing and balance at all times. Properfooting

and balance enables better control of the power tool in unexpected situations.

15. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

16. Use clamps (not included) or other practical ways to secure and support the

workpiece to a stable platform. Holding the work by hand or against your body is

unstable and may lead to loss of control.

17. Do not force the tool. Use the correct tool for your application. Thecorrect tool

will do the job better and safer at the rate for which it is designed.

18. Do not use the power tool if the Power Switch does not turn it on or off. Any

tool that cannot be controlled with the Power Switch is dangerous and must be

replaced.

19. Disconnect the Power Cord Plug from the power source before making any

adjustments, changing accessories, or storing the tool. Such preventivesafety

measures reduce the risk of starting the tool accidentally.

20. Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

21. Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools with a sharp cutting edge are less likely to bind and are easier to

control. Do not use a damaged tool. Tag damaged tools “Do not use”until repaired.

22. Check for misalignment or binding of moving parts, breakage of parts, and

any other condition that may affect the tool’s operation. If damaged,have the

tool serviced before using. Many accidents are caused by poorly maintained

tools.

23. Use only accessories that are recommended by the manufacturer for your

model. Accessoriesthat maybesuitable foronetool maybecomehazardous when

used on another tool.

TOOL USE AND CARE

Page 5SKU 93431 For technical questions, please call 1-800-444-3353.

SPECIFIC SAFETY RULES

1. Hold tool by insulated gripping surfaces when performing an operation where

the sanding tool may contact hidden wiring or its own cord. Contact with a

“live” wire will make exposed metal parts of the tool “live” and shock the

operator.

2. Maintainlabels and nameplates on theSander. Thesecarryimportantinformation.

If unreadable or missing, contact Harbor Freight Tools for a replacement.

3. Alwayswear safety impact eye gogglesand a dust mask/respirator whenusing

or performing maintenance on this tool. Using personal safety devices reduce

the risk for injury. Safety impact eye goggles and dust mask/respirator are available

from Harbor FreightTools.

4. Maintain a safe working environment. Keep the work area well lit. Make sure

there is adequate surrounding workspace. Always keep the work area free of

obstructions, grease, oil, trash, and other debris. Do not use a power tool in areas

near flammable chemicals, dust, and vapors. Do not use this product in damp or

wet locations.

5. When using a handheld power tool, always maintain a firm grip on the tool

with both hands to resist starting torque.

6. Always keep the extension cord away from moving parts of the tool.

7. Avoid unintentional starting. Make sure you are prepared to begin work before

plugging in the Sander.

8. Do not force the Sander. This tool will do the work better and safer at the speed

and capacity for which it was designed.

9. Never lay the Sander down until the rotating pad has come to a complete stop.

The rotating pad can grab the surface and putll the tool out of your control.

10. Never leave the Sander unattended when it is plugged into an electrical outlet.

Turn off the tool, and unplug it from its electrical outlet before leaving.

SERVICE

24. Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

25. Whenservicingatool,use only identical replacement parts. Follow instructions

in the

“Inspection,Maintenance,And Cleaning”

section of this manual. Use of

unauthorized parts or failure to follow maintenance instructions may create a risk of

electric shock or injury.

Page 6SKU 93431 For technical questions, please call 1-800-444-3353.

11. Always unplug the Sander from its electrical outlet before performing any

inspection, maintenance, or cleaning procedures.

12. WARNING! People with pacemakers should consult their physician(s) before

using this product. Electromagneticfieldsinclose proximitytoaheart pacemaker

could cause interference to or failure of the pacemaker.

In addition, people with pacemakers should adhere to the following:

• Avoid operating power tools alone.

• If powered via a power cord be certain that the tool is properly grounded. A

groundfaultinterrupt (GFCI)systemis also a goodprecaution. Thisinexpensive

deviceisa goodsafety measurebecause itprevents asustained electricalshock.

• Properly maintain and inspect all tools before use to avoid electrical shock.

13. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities, contain chemicals known (to the State of California) to

cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks and cement or other masonry products.

• Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area,

andworkwithapprovedsafetyequipment,suchasthosedustmasksthatarespecially

designed to filter out microscopic particles.

(California Health & Safety Code § 25249.5,

et seq.

)

14. Take caution as some woods contain preservatives such as copper chromium

arsenate (CCA) which can be toxic.Whencuttingthesematerialsextracareshould

be taken to avoid inhalation and minimize skin contact.

15. WARNING! Exposureto aluminum oxide(adust generated frommaterialremoving

processes) can result in eye, skin, and respiratory irritation. Always use a NIOSH

(NationalInstituteforOccupationalSafetyand Health)approved respiratorand ANSI

approved safety goggles. Avoid skin exposure. Proper ventilation in the work area

is required.

16. WARNING! The warnings, cautions, and instructions discussed in this instruction

manual cannot cover all possible conditions and situations that may occur. It must

be understood by the operator that common sense and caution are factors which

cannot be built into this product, but must be supplied by the operator.

Note: Performance of this tool (if powered by line voltage) may vary depending on

variationsinlocallinevoltage.Extensioncord usage may also affect tool performance.

Page 7SKU 93431 For technical questions, please call 1-800-444-3353.

GROUNDING

WARNING!

Improperly connecting the grounding wire can result in the risk of electric

shock. Check with a qualified electrician if you are in doubt as to whether the

outlet is properly grounded. Do not modify the power cord plug provided with

the tool. Never remove the grounding prong from the plug. Do not use the

tool if the power cord or plug is damaged. If damaged, have it repaired by a

service facility before use. If the plug will not fit the outlet, have a proper outlet

installed by a qualified electrician.

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

1. Tools marked with “Grounding Required” have a three wire cord and three prong

grounding plug. The plug must be connected to a properly grounded outlet. If the

tool should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user, reducing the risk of electric

shock. (See Figure A.)

2. The grounding prong in the plug is connected through the green wire inside the

cordto the grounding systemin the tool. The greenwire in thecordmust be the only

wire connected to the tool’s grounding system and must never be attached to an

electrically “live” terminal. (See Figure A.)

FIGURE A

Page 8SKU 93431 For technical questions, please call 1-800-444-3353.

3. Your toolmustbe pluggedinto anappropriate outlet,properly installedand grounded

in accordance with all codes and ordinances. The plug and outlet should look like

those in the following illustration. (See Figure A.)

DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

4. Tools marked “Double Insulated” do not require grounding. They have a special

double insulation system which satisfies OSHA requirements and complies with

theapplicable standards of Underwriters Laboratories,Inc., the Canadian Standard

Association, and the National Electrical Code. (See Figure B.)

5. Double insulated tools may be used in either of the 120 volt outlets shown in the

following illustration. (See Figure B.)

FIGURE B

Note:

This tool has a

2 Prong Plug.

Page 9SKU 93431 For technical questions, please call 1-800-444-3353.

EXTENSION CORDS

Grounded

tools require a three wire extension cord.

Double Insulated

tools can

use either a two or three wire extension cord.

2. As the distance from the supply outlet increases, you must use a heavier gauge

extension cord. Using extension cords with inadequately sized wire causes a

serious drop in voltage, resulting in loss of power and possible tool damage.

(See Figure C.)

3. The smaller the gauge number of the wire, the greater the capacity of the cord.

For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.

(See Figure C.)

4. When using more than one extension cord to make up the total length, make sure

each cord contains at least the minimum wire size required. (See Figure C.)

5. If you are using one extension cord for more than one tool, add the nameplate

amperes and use the sum to determine the required minimum cord size. (See

Figure C.)

6. If you are using an extension cord outdoors, make sure it is marked with the suffix

“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

7. Make sure your extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualified

electrician before using it.

8. Protect your extension cords from sharp objects, excessive heat, and damp or wet

areas.

*SDROCNOISNETXEROFEGUAGERIWMUMINIMDEDNEMMOCER

ETALPEMAN SEREPMA )daoLlluFtA( HTGNELDROCNOISNETXE

teeF52teeF

05teeF57teeF001teeF051

0.2-08181818161

4.3-1.28181816141

0.5-5.38181614121

0.7-1.58161412121

0.21-1.781412101-

0.61-1.21412101--

0.02-1.612101---

CERUGIF evifotpordegatlovenilehtgnitimilnodesaB* .serepmadetarehtfo%051tastlov

Page 10SKU 93431 For technical questions, please call 1-800-444-3353.

SYMBOLOGY

UNPACKING

When unpacking, check to make sure that the item is intact and undamaged. If any parts

are missing or broken, please call Harbor FreightTools at the number shown on the cover

of this manual as soon as possible.

ASSEMBLY INSTRUCTIONS

NOTE: For additional information regarding the parts listed in the following pages, refer

to the Assembly Diagram on page 13.

CAUTION: Always make sure the Power Cord (13) of the Sander is unplugged from its

electrical outlet prior to making any adjustments or doing servicing, or adding or remov-

ing sanding discs.

ATTACHING THE DUST BAG (28)

1. Slide the Dust Bag (28) onto the back of the Sander. Snap it in place using firm

pressure.

2. Thecollectionof thedust will only

work if the sandpaper has holes

that line up with the 8 dust

collection holes in the Backing

Pad (23).There are 4 other holes

inthe BackingPad fortheScrews

(26) that attach the Backing Pad

tothe Sander.

DustBag (28)

BackingPad(23)

Altri manuali per 93431

Indice

Altri manuali Chicago Electric Levigatrice

Chicago Electric

Chicago Electric 94338 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 90045 Manuale utente

Chicago Electric

Chicago Electric 43424 Assembly and Manuale utente

Chicago Electric

Chicago Electric 94748 Manuale elenco delle parti

Chicago Electric

Chicago Electric 66615 Manuale di installazione

Chicago Electric

Chicago Electric 69924 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 45813 Manuale utente

Chicago Electric

Chicago Electric 92194 Manuale utente

Chicago Electric

Chicago Electric 62297 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 41213 Manuale utente

Chicago Electric

Chicago Electric 90979 Manuale utente

Chicago Electric

Chicago Electric 92158 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 69820 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 90820 Manuale utente

Chicago Electric

Chicago Electric 69917 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 95020 Manuale elenco delle parti

Chicago Electric

Chicago Electric 66891 Manuale di installazione

Chicago Electric

Chicago Electric 97593 Manuale di installazione

Chicago Electric

Chicago Electric 42864 Manuale elenco delle parti

Chicago Electric

Chicago Electric 95020 Manuale utente

Chicago Electric

Chicago Electric 69924 Manuale utente

Chicago Electric

Chicago Electric 93431 Manuale di installazione

Chicago Electric

Chicago Electric 67256 Manuale di installazione

Chicago Electric

Chicago Electric 41213 Manuale di installazione

Manuali Levigatrice popolari di altre marche

Oliver

Oliver 6305 Manuale utente

Jet

Jet 22-44 Pro-3 Manuale di servizio

Makita

Makita M9204 Manuale

Makita

Makita M9204 Manuale utente

Craftsman

Craftsman 351.215131 Manuale utente

Clarke

Clarke Woodworker CBS1-5B Manuale di istruzioni

Chicago Pneumatic

Chicago Pneumatic CP9778 Manuale utente

Nitto Kohki

Nitto Kohki BB-20 Manuale utente

Ferm

Ferm FEOS-135 Manuale utente

Unior

Unior 1510 Manuale utente

stayer

stayer ls1200 Manuale utente

Jet

Jet JSG-96 Manuale di servizio

Parkside

Parkside PDS 290 B2 Manuale utente

Status

Status XPA Series Manuale utente

Clarke

Clarke EZ Sand Manuale utente

Craftsman

Craftsman 113.22521 Manuale utente

Craftsman

Craftsman 113.225831 Manuale utente

CLAS

CLAS OP 1429 Manuale utente