CHIEF FDP Series Manuale utente

8803-000033 01/26/04

CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: [email protected]

INSTALLATION INSTRUCTIONS

FDP SERIES

SMALL FLAT PANEL DISPLAY

DUAL SCREEN POLE MOUNT

Exclusive Q2™ Mounting System

Prior to assembly, unpack carton completely and verify contents.

If you are missing any of the following components, please contact Customer Service at 1-800/582-6480.

(2) FDP Pole-Mounting Bracket Half (2) ¼” Flat Washer

(2) ¼-20 X 4.25” Hex Bolt (8) 10-24 X 1.00 Thread Forming Screw

(8) ½” X ½” Nylon Spacer

BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY

The FSP will fit on any 1/1/2” to 2” O.D. pipe including 1 ½”NPT.

Flat Panel Displays are Extremely Fragile.

If Monitor Uses a Screw Size Other Than M4 X 10mm (M4 X 20mm),

DO NOT USE M4 Screws Provided. Monitor Damage Could Occur.

Interface Bracket Installation:

1. See installation procedures accompanying your mounting bracket.

Optional Latching Flag Placement:

1. Remove Phillips head screw, Nylock nut and latching flag (see Figure 2).

2. Reposition latching flag and secure using Phillips head screw, Nylock nut.

Figure 1

Figure 2

CAUTION!

Remove screw

and nu

ove

atc

8803-000033 01/26/04

CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: [email protected]

Pole-Mounting Bracket Assembly and Installation:

1. Assemble two pole-mounting bracket halves as shown in Figure 3 and secure using two ¼-20 X 4.25”

hex bolts and two ¼” flat washers.

2. For vertical pole mounting, install the pole-mounting bracket on 1 ½” to 2” OD pipe/pole and secure

using 7/16” hex drives (see Figure 4).

3. For horizontal pole mounting; remove eight tilt adjustment screws, reposition the tilt bracket as

shown in Figure 5, and insert nylon spacers. Secure using 10-24 x 1.00 screws provided.

Mounting Display with Interface Bracket to Pole-Mounting Bracket:

1. Make sure both latching flags on pole-mounting bracket are in the unlocked position (see Figure 4).

2. Place your small flat panel displays; with interface brackets attached, onto the pole-mounting bracket,

making sure they are securely seated.

3. Engage pole-mounting bracket latching flags, locking small flat panel displays in place (see Figure 6).

4. Adjust tilt by loosening (slightly) tilt adjustment screws (see Figure 7) on each side of pole-mounting

bracket, adjust to desired angle, and tighten tilt adjustment screws.

Figure 3 Figure 4

Locked

Unlocked

Tighten to

secure to

ole

Tilt

Adjustment

Screws

Figure 6

10-24 x 1.00 screw

.500 O.D. x .500

long nylon spacer

Figure 7

¼-20 X 4.25” hex bolt

and ¼” washer

Figure 5

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali CHIEF Rack e supporto

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente