Chord CB-25 Manuale utente

CB-25

Bass Amplifier

Item ref: 173.442UK

User Manual

Version 1.1

Caution: Please read this manual carefully before operating

Damage caused by misuse is not covered by the warranty

173.442UK User Manual

Introduction

Thank you for choosing our CB series bass amplifier. Please read this manual prior to use to avoid damage to the item.

The CB range is specifically designed to give the bass player a powerful, dependable amplifier with enough useful

features to suit a wide variety of situations from rehearsal to stage.

Warning

To prevent the risk of fire or electric shock, do not expose this appliance to rain or moisture. To prevent electric shock do

not remove the cover. No user serviceable parts inside. Refer servicing to qualified service personnel.

Safety

•Prior to connecting mains, ensure that the supply voltage is correct, and the mains lead is in good condition.

•Avoid ingress of water or particles into the enclosure.

•If the mains fuse blows, refer the unit to qualified service personnel.

•Keep the unit out of direct sunlight and away from heat sources.

•Place the unit in an upright position during use and storage.

•Keep the unit away from moisture or dusty environments.

Cleaning

Use a soft cloth with a neutral detergent to clean the cabinet, panel and controls. To avoid damage, do not use solvents.

Controls and Connectors

1. IEC power inlet & fuse holder

2. Input –6.3mm jack (unbalanced)

3. Gain control –Turning clockwise boosts input and increases drive

4. Low EQ control

5. Low-Mid EQ control

6. High-Mid EQ control

7. High EQ control

8. Master output level

9. Phones –6.3mm jack output to drive headphones

10. MP3 in –3.5mm jack socket to plug in a line input to play along with.

11. Power –Illuminated mains switch

173.442UK User Manual

Operation

Connect the bass guitar to the CB-series bass amplifier input using a good quality 6.3mm mono jack lead.

Connect the amplifier to the mains using the appropriate mains IEC lead supplied.

Set all EQ controls to the mid-way position.

With the Master volume turned down, switch on the power switch and gradually increase the Master volume to the

required level.

Increase Gain and play a note, ensuring that the bass guitar’s volume and tone controls are turned up. Continue

increasing Gain until the required signal level and drive amount are achieved.

Adjust the 4 EQ controls to boost or cut the relevant frequency ranges that produce the tonal response required.

Low and Low-Mid cover the bass frequencies, whereas High-Mid and High cover the treble frequencies.

Some experimentation is needed to achieve the best results from the EQ and will depend on how much low frequency

punch and higher frequency detail is needed.

Plugging in a pair of headphones to the 6.3mm Phones jack will allow silent practice by muting the speaker output.

Plugging a personal stereo playback device (like an mp3 player) into the MP3 mini-jack input allows the music to be

mixed in with the bass guitar sound for “play-along” practice.

Before switching off or removing power, turn down the Master volume control.

173.442UK User Manual

Specifications

Troubleshooting

No output and no Power light

Check POWER switch is on and mains lead is connected properly

Check mains fuse hasn’t blown

Power LED lit but no Output

Check that Gain, EQ, Master and bass guitar controls are not turned down fully

Check Speaker Outs are connected to the relevant speakers

Check that headphones are not left plugged in

Change jack lead to check if faulty, also for Send and Return jacks

Check battery is OK in active bass or effects units in the Send/Return loop

Output too distorted

Make sure Active bass is not plugged into Passive input

Reduce Gain & EQ controls and increase Master volume to compensate

Adjust compression effect to combat heavy string attack

Output very quiet

Check that Gain, EQ, Master and bass guitar controls are not turned down

Make sure passive bass is not plugged into Active input

Unplug effects from Send/Return loop to check if they are cutting signal level

Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or

Electronic equipment and should not be disposed with other household or commercial waste

at the end of its useful life. The goods must be disposed of according to your local council guidelines.

AVSL Group Ltd. Unit 2-4 Bridgewater Park, Taylor Rd. Manchester. M41 7JQ

AVSL (EUROPE) Ltd, Unit 3D North Point House, North Point Business Park, New Mallow Road, Cork, Ireland

Power supply

220-250Vac, 50/60Hz (IEC)

Output power @ 8Ω

25Wrms

Speaker unit(s)

8" HD driver

Input

6.3mm jack + 3.5mm Aux jack

Phones Out

6.3mm jack

Preamp Controls

Gain, Master

Equalisation

4-band EQ

Dimensions

365 X 395 X 300mm

Weight

12kg

Questo manuale è adatto per i seguenti modelli

Altri manuali Chord Amplificatore

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente