Christie GraphXMASTER DLV1400-DX Manuale utente
Lamp and Filter Replacement Instruction Sheet 1 of 6
020-100160-02 Rev. 1 (01-2012)
Lamp and Filter Replacement
Instruction Sheet
INTRODUCTION
Use the following instructions when replacing the lamp or filters in one of the projectors listed under
Kits Required. Christie® recommends that lamps and filters be checked approximately every 1000
hours under normal operating conditions. Use only a Christie approved Lamp and Filter Kit for your
projector model.
When do I replace a lamp? Replace the lamp when it reaches its end of life or sooner if a noticeable
degradation in brightness occurs. You can set the number of hours you expect to log with the lamp
before replacing it, by setting the lamp limit in the lamp menu of the projector software. This setting
should not exceed the lamp lifetime warranty. Enable the lamp message checkbox to provide a warning
upon power up to indicate the lamp has reached the set lamp limit. At this time the lamp should be
replaced.
WARNINGS AND GUIDELINES
EXPLOSION HAZARD! Lamps are under high pressure and may contain
hazardous materials. Always wear an authorized full face shield and protective
clothing to protect eyes and arteries when handling lamps.
Lamp replacement must be performed by a qualified service technician.
To avoid personal injury, always let the lamp cool completely before handling,
and always handle the lamp by the housing only.
Always use the correct wattage lamp supplied by Christie. Read the entire lamp
replacement procedure and all warnings before servicing.
Never touch the glass surface of the lamp. Fingerprints left on the surface can
lead to an intense accumulation of heat called a “hot spot”, which could
potentially result in lamp explosion during normal operation.
2 of 6 Lamp and Filter Replacement Instruction Sheet
020-100160-02 Rev. 1 (01-2012)
KITS REQUIRED
TOOLS REQUIRED
• #2 Phillips screwdriver
• Personal protective equipment (lint-free gloves, full face shield)
PROJECTOR MODEL WATTAGE LAMP/FILTER KIT REQUIRED
DLV1400-DX
DLV1920-DX
Matrix HD2
Matrix WU2
Christie HD2Kc
Matrix S+2K
Mirage HD3
Mirage WU3
Christie HD3K
Mirage S+3K
500W 003-120118-XX
Matrix 4000
Matrix HD4
Christie DW4Kc
Matrix WU5
Christie DS+5Kc
Christie HD5Kc
Christie DW5K
Matrix S+5K
Christie DS+6K
Mirage S+6K
Christie HD6K
Mirage HD6
Mirage WU7
1000W 003-120117-XX
Christie DW6Kc
Matrix HD7
Christie HD7Kc
Christie DS+8K
Christie DW8K
Christie HD8K
1200W 003-120116-XX
HD7K-J
Mirage HD7K-J
Mirage WU7K-J
Matrix WU7K-J
DS+8K-J
Mirage DS+8K-J
1000W 003-004084-XX
HD9K-J
DS+10K-J 1200W 003-004085-XX
Lamp and Filter Replacement Instruction Sheet 3 of 6
020-100160-02 Rev. 1 (01-2012)
INSTRUCTIONS
Remove the Lamp Module
1. Press power twice to switch the lamp off. Allow the cooling fans to stop automatically (within 5
minutes) before proceeding with step 2.
NOTE: This wait period is required to allow the lamp to sufficiently cool before handling.
2. When the cooling fans have stopped, unplug the projector.
3. Loosen (2) #2 Phillips® self retaining screws to open the lamp door. Remove the lamp door.
NOTICE! The lamp door is not tethered.
4. Pull back and turn the locking lever counter clockwise to the 12 o’clock position to unlock the
lamp module for removal.
5. Grasp the body of the lamp housing at the top and the bottom. Pull the lamp module straight back
to remove it from the projector.
Keep knuckles raised in order to prevent injury.
4 of 6 Lamp and Filter Replacement Instruction Sheet
020-100160-02 Rev. 1 (01-2012)
Install the Lamp Module
1. Verify that the lamp memory board - located on the rear left of the lamp - is not obstructed. If it is
covered with a plastic protector, remove it before installing the lamp. Failure to do this will
hamper the proper installation of the lamp and prevent normal operation.
2. Record the serial number of the new lamp.
3. Align the new lamp with the top and bottom guides on the left side of the lamp compartment. Slide
the lamp all the way in – a slightly harder push may be required right at the end to make sure the
lamp is fully seated into the terminal block.
NOTE: The lamp module must make full contact with the terminal block. The projector will not
power up again if the lamp is not fully connected to the terminal block.
4. Pull and turn the locking lever clockwise to 3 o’clock to secure the lamp module.
NOTE: If the locking lever cannot be easily turned, then the lamp is not fully inserted.
5. Install the lamp door and secure (2) #2 Phillips® self retaining screws.
6. Plug in and power on the projector and navigate to the lamp menu. Select CHANGE LAMP. This
will prompt for the old lamp serial number (if it was not previously entered). Enter the new lamp
serial number.
NOTE: This action is not mandatory, it is recommended for accurate lamp statistics to be
archived. If you neglect to enter a serial number, the lamp times will not reset to “0” and will
therefore be inaccurate, in which case, the lamp life limit will expire prematurely.
Lamp and Filter Replacement Instruction Sheet 5 of 6
020-100160-02 Rev. 1 (01-2012)
Replace the Air Filter
J Series Projectors:
1. Loosen (2) #2 Phillips® self retaining screws on the filter
cover.
2. Remove the filter cover
3. Remove the filter and discard. Do not reuse filters.
4. Insert the new filter.
5. Install the filter cover and secure with (2) #2 Phillips® screws.
Non-J Series Projectors:
1. Loosen (4) #2 Phillips® screws on the filter access panels. (Front access panel located to the left of
the lens - 1 screw. Left side access panel - 3 screws.)
2. Pull the old filters out of the projector and discard. Do not reuse filters. Insert the new filters with
the wired side in.
3. Install the filter access panels and secure with (4) #2 Phillips® screws.
6 of 6 Lamp and Filter Replacement Instruction Sheet
020-100160-02 Rev. 1 (01-2012)
TECHNICAL SUPPORT CONTACT INFORMATION
NORTH AMERICA
Christie Digital Systems, Inc.
809 Wellington Rd. North
Kitchener, Ontario, Canada N2G 4Y7
Tel: 519-744-8005 (General)
Fax: 519-749-3302 (Service)
Toll Free: 1-800-221-8025 (Technical Support)
Christie Digital Systems, Inc.
10550 Camden Drive
Cypress, CA 90630 USA
Tel: 714-236-8610 (General)
Fax: 519-749-3302 (Service)
Toll Free: 1-800-221-8025 (Technical Support)
EUROPE
Christie Digital Systems, Inc.
ViewPoint
200 Ashville Way
Workingham, Berkshire RG412PL
United Kingdom
Tel: +44-118-977-8111
Fax: +44-118-977-8112
Christie Digital Systems, Inc.
Willicher Damm 129
D-41061 Mönchengladbach
Germany
Tel: +49-2161-664540
Fax: +49-2161-664546
Christie Digital Systems, Inc.
7, av Georges Pompidou
92593 Levallois-Perret Cedex
France
Tel: +33-(0)1-47-48-28-07
Fax: +33-(0)1-47-48-26-06
ASIA-PACIFIC/OTHER
Christie Digital Systems, Inc.
627A Aljunied Road
# 05-02 Biz Tech Center
Singapore 389842
Tel: 65-6877-8737
Fax: 65-6877-8747
Christie Digital Systems, Inc.
Rm. 1109-1116 Shartex Plaza
No. 88 Zun Yi South Road
Shanghai, 200336
People’s Republic of China
Tel: +86-21-6278-7708
Fax: +86-21-6270-5816
Altri manuali per GraphXMASTER DLV1400-DX
3
Questo manuale è adatto per i seguenti modelli
36
Indice
Altri manuali Christie Proiettore
Christie
Christie RoadRunner LX100 Manuale utente
Christie
Christie LW400 Manuale utente
Christie
Christie CP2000-SB Manuale utente
Christie
Christie CP2420-Xe Istruzioni per il montaggio
Christie
Christie D4K3560 Manuale utente
Christie
Christie Matrix 3500 Manuale utente
Christie
Christie CP42LH Manuale utente
Christie
Christie D4K2560 Manuale utente
Christie
Christie Roadster S+14K-J Manuale utente
Christie
Christie MultiSync EA274WMi Manuale utente
Christie
Christie CP2306-RGBe Guida rapida
Christie
Christie APS Series Manuale per l'uso e la cura
Christie
Christie LW400 Manuale utente
Christie
Christie CineLife+ CP4415-RGB Manuale utente
Christie
Christie HS 2K Series Manuale utente
Christie
Christie LWU505 Manuale utente
Christie
Christie CP2215 Manuale utente
Christie
Christie 38-RS1002-01 Manuale utente
Christie
Christie CineLife+ CP4440-RGB Istruzioni per il montaggio
Christie
Christie Roadie 4K35 Manuale utente
