CIG WF-180 Manuale utente
WF-180 Wireless Access Point
Thank you for buying this product. The following information aims to give you general
information about product introduction, product overview and installation procedure and
so on.
1. Introduction
WF-180 is a dual-band 2x2streams and chains indoorWi-Fi AP, which is complied with the
IEEE802.11n standard and designed for high-density deployments in offices, schools,
hospitals and hotels that require premium performance.
Having together MIMO (Multiple-in&Multiple-out) technology with high-throughput mode
techniques, WF-180 works with most wireless terminals to builds a high capacity Wi-Fi
network.
2. Package List
•AP x1
•Wall bracket x1
•Ceiling bracket x 1
•Screw x1
•Cable tie x1
3. Product Overview
No.
Name
Function
LEDs
See LED Definition
LAN Port
10/100/1000M Base-T Ethernet ports(RJ-45), used as a
WAN port and used for being powered by PoE function.
Console port
Also names as RJ-11, used to manage WF-180 software.
Reset button
Pressing the button longer than 5s to restore the device to
factory defaults and reset the device.
DC power connector
used for connecting the power adapter
USB port
supports a USB 2.0 connector(Support up to 0.5A)
Kensington Lock Slot
For additional security
4. Installation
To reduce the risk of bodily injury, electrical shock, fire, and equipment
Damage, read all warnings and precautions in this guide before
Installing or maintaining product.
Caution
To avoid risk of injury from electrical shock or energy hazard, installation and service
of this product must be performed by qualified service personnel.
Make sure the AP fits securely on the ceiling rail when hanging the device in the
ceiling, because poor installation could cause it to fall and make body injury and
equipment damage.
Safety Statement
•To avoid the abnormal work, do not install the device near the power line,
electric lamp, power grid, or in any forceful power grid place
•Ensure the power adapter is grounded well if install the device indoor.
•Install other lightning protection equipment near the device if necessary,
because the lightning protection module inside the device is basic.
•Use the steady power grid to provide the power to the device, which is to avoid
the abnormal work.
•Use a less than 50m network cable to connect the PoE port, which is to acquire
the steady power. The network cable complies with the DC resistance
definition in the YD/926.2 protocol.
Installation Environment
•Operating ambient temperature: 0℃~ 45℃
•Operating ambient humidity: 5% ~ 95% non-condensing
Installation mode:
•Wall mounting and Cliling mounting.
Installation tool:
•Screws and screw-driver
Installation site:
Please ensure the visibility of product and no tall buildings and woods block
between them.
Installation procedure
Wall mounting
1. Drive two screws fist in the wall. The distantbetween two screws mounted on the
wall is 40mm.
2. Align bracket with the screw, and then pull down the bracket with up to down
direction until it has been fixed tightly.
3. Align the securing hookof AP with bracket, and push AP from up to down until it
has been locked fully.
Ceiling mounting:
1. Fasten ceiling railsby pushing bracket as the indicated direction
2. Secure the screw to fasten bracket assembly.
2.3. Align securing hookof AP with bracket (see dotted line), and then push AP close
to bracket until AP has been fully Locked
3.4. Go through locking holes by cable-tie to safely content AP with bracket
5. LED Definition
LED
Function
State-Color
Indication
RUN
AP power / ready status
Steady - Green
APis ready
Flashing - Green
AP is managed by controller
Red
AP hardware failure
Off
No power to AP
LAN
Network Link Status
Steady - Green
1000Mbps Ethernet link negotiated
Steady- Yellow
Reserved for link speed (NIB in PCB)
Flashing
Ethernet link activity
Off
Ethernet link unavailable
5G
5G Hz Radio Status
Steady–Green
5G Hz radio enabled in HT WLAN
mode
Off
5G Hz radio disabled
2.4G
2.4G Hz Radio Status
Steady –Green
2.4G Hz radio enabled in HT WLAN
mode
Off
2.4G Hz radio disabled
6. Software Installation
Logging in to the Web Page
1. To configure PC IP address, fill 192.168.188.x in “IP address” and 255.255.255.0
in “Subnet mask”(set Window7 as an example to show the properties)
2. Input the default IP address 192.168.188.251 in the address bar of the web
browser and press Enter.
3. Enter username and password (username: admin, password: password), after
password authentication is successful, the web page is displayed.
7. Product Specification
Physical specification
Dimensions
160 mm x 160 mm x 40mm(Width x Length x Height)
Weight
Less than 1kg
LEDs
RUN,LAN,5GHz,2.4GHz
Ethernet interface
RJ-45 connector
Electrical specification
Power input
+12V/1A
Power consumption
≤12W
Environmental specification
Working temperature
0℃~ 45℃
Working humidity
5% ~ 95% non-condensing
Elevations
86kPa～106kPa
Dustproof and waterproof
IP30
Lightning protection
4KV common mode surge
8. Product Proper Disposal
Waste of Electrical and Electronic Equipment
Directive 2002/96EC on Waste of Electrical and Electronic Equipment are designed
to tackle the fast increasing waste stream of electrical and electronic equipment and
complements European Union measures on landfill and incineration of waste. CIG
products at end of life are subject to separate collection and treatment in the EU Member
Statues and therefore are marked with the symbol.
European Union RoHS
EU Restriction and Hazardous Substances Directive 2011/65/EC (RoHS) restricts
the use of specific hazardous materials in manufacture of electrical and electronic
equipment. Specially, restricted materials are Lead, Cadmium, Mercury, Hexavalent
Chromium, and Bromine. CIG products comply with this requirement and all marked with
“RoHS”shown at the left.
China RoHS
WF-180 AP complies with China environmental declaration requirements and is labeled
with “EFUP 20”label shown as follows.
有毒有害物质声明
Hazardous Materials Declaration
部件名称
（Parts）
有毒有害物质或元素（Hazardous Substance）
铅
（
P
b
）
汞
（
H
g
）
镉
（
C
d
）
六价铬
（
C
r6
+
）
多溴联苯
（
P
BB
）
多溴二苯醚
（
P
B
D
E
）
电路模块
（circuit modules）
×
O
O
O
O
O
电缆及电缆组件
（Mechanicalassembli
x
O
O
O
O
O
es）
金属部件
（Metal Parts）
O
O
O
O
O
O
塑料和聚合物部件
（Plastic and
Polymeric Parts）
O
O
O
O
O
O
O：
表示该有毒有害物质在该部件所有均质材料中的含量在 SJ/T11363 －2006标准规定的限量要求下。
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts
is below the relevant threshold of the SJ/T11363-2006 standard.
X：
表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006标准规定的限量要求。
Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
对销售之日的所售产品，本表显示剑桥公司供应链的电子信息产品可能包含这些物质。注意：在所售产
品中可能会也可能不会含有所有所列的部件。
This table shows where these substances may be found in the supply chain of CIG electronic
information products, as of the date of sale of the enclosed product. Note that some of the component
types listed above may or may not be a part of the enclosed product.
9. Safety and Regulatory compliance
WF-180 AP has been tested and complied with the standards as follows:
•FCC Part 15 Subpart C 15.247 (US)
•FCC Part 15 Subpart E 15.407 (US)
•CE marked with NB letter of opinion for:
•ETSI EN 300 328 (2.4GHz)
•ETSI EN 301 893 (5GHz)
•CB with IEC/EN 60950-1 (Basic safety certificate for worldwide marketing)
11.10. FAQs
除非另外特别的标注，此标志为针对所涉及产品的环保使用期标志。某些零部件会有一个不同的环
保使用期贴在其产品上。此环保使用期限只适用于产品是在产品手册中规定的条件下工作。
The Environment-Friendly Use Period (EFUP) for all enclosed products and their parts are per the
symbol shown here, unless otherwise marked. Certain parts may have a different EFUPand so are
marked to reflect such. The Environment-Friendly Use Period is valid only when the product is
operated under the conditions defined in the product manual.
Indice
