Cima Above Ceiling ElectriScreen Manuale utente
TO THE INSTALLER: BE SURE TO LEAVE THIS MANUAL WITH THE OWNER.
CFS-080315-AC
To the Owner
Installation Instructions
Screen Care
Maintenance
Owner’s Manual
Above Ceiling ElectriScreen
Printed in U.S.A.
© 2015 Stewart Filmscreen Corporation
Stewart Filmscreen reserves the right to make changes to the product specified in this document.
Sizes and specifications subject to change without notice at Manufacturer’s discretion. From time to time, this
document is updated. Current versions of documentation are posted on the Stewart Filmscreen website at:
www.stewartfilmscreen.com
To the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Preparing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . 5
Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the Screen Into the Ceiling . . . . . . . . . . . . . . . . . . . 7
Standard Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
Keypad Control . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Projector Control . . . . . . . . . . . . . . . . . . . . . . . . . 9
Keypad & Projector Control . . . . . . . . . . . . . . . . . . . . 10
Optional Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
Cima-Link Infrared Package . . . . . . . . . . . . . . . . . . . . 12
Cima-Link Ethernet Package . . . . . . . . . . . . . . . . . . . 13
Cima-Link RS232 Package . . . . . . . . . . . . . . . . . . . . 14
Operating the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjusting the Screen Extension . . . . . . . . . . . . . . . . . . . . 16-17
Adjusting the Screen Tension . . . . . . . . . . . . . . . . . . . . . . . 18
Caring for & Cleaning the Screen . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21
Product Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Contents
Owner’s Manual
Above Ceiling ElectriScreen
4Cima Above Ceiling ElectriScreen: Owner’s Manual
© 2015 Stewart Filmscreen Corporation
♦Carefully read the instructions appropriate for your needs.
♦This screen must be installed by a qualified electrician.
♦For supply connections, use wires rated for at least 75 C.
♦Use copper or aluminum conductors.
♦For indoor use only.
♦Do not connect low-voltage to line-voltage power.
♦Article 725-54(a), (1) Exception No. 3 (NEC) or Canadian CE Code Handbook,
Rule 16-212, Sub Rule (4) requires segregation between line-voltage and Class 2
(low-voltage) circuits. Low-voltage / network wires should enter enclosure boxes
through separated openings. Also, conductors shall be separated by at least 1/4" or
segregated by barriers. Check with your local electrical inspector for compliance with
local / national codes and wiring practices.
♦Earth ground terminal connection must be made as shown in wiring diagrams.
♦Proper short-circuit and overload protection must be provided at the circuit breaker
distribution panel. You can use up to a 20A maximum circuit breaker with adequate
short-circuit breaking capacity for your installation.
IMPORTANT SAFETY INFORMATION
About your Cima Above Ceiling ElectriScreen
SAFETY PRECAUTIONS
The Cima Above Ceiling ElectriScreen is designed for ease of installation. The Cima
Above Ceiling features a self-finishing face-plate. There are no user-servicable
parts contained within the unit.
Congratulations on your purchase of one of our highly versatile Cima projection
screens representing “Top of the Class” in standard commercial and residential
projection screens. Please take a moment to review this manual as it will help
ensure you many years of trouble-free service from your new Cima by Stewart
Filmscreen product.
TO THE OWNER
5
© 2015 Stewart Filmscreen Corporation
To be installed and/or used in accordance with appropriate electrical codes and
regulations.
Caution
The Cima Above Ceiling's screen motor is pre-wired at the factory. No additional
motor assembly is required
Motor Wiring
1. Remove the outer plastic covering and white wrapping paper surrounding the
screen case.
2. Do not remove the wrapping paper surrounding the screen roller. You should
remove it only after the unit is hung and all electrical connections have been made.
Unpacking
Note: This manual refers to “AC” to represent electrical power. Your location may
use 120 V, 220 V, or other electrical power. Screen systems are manufactured
using the electrical power type specified for the location. Use appropriate power
sources for your location.
♦Enough ladders for the personnel supporting the screen during the mounting process
♦A level
♦Fasteners appropriate for the surface on which the screen is being mounted (See
instructions for the type of mount for recommendations.)
You will need:
During installation, do not place the unit on an unstable cart, stand, table, or
ladder. The unit may fall, causing injury and damage to the unit.
Caution
The Cima Above Ceiling product can be controlled through a number of remote
control devices, including keypads, dry contact outputs, and low-voltage trigger
outputs. With the optional Cima-Link Controller Packages, your Cima screen can be
controlled by local and remote Infrared, IP ethernet, and computer-based signaling
sources such as those manufactured by Control4, AMX, Crestron, Elan Home
Systems with RS-232-C or RS-485 interfaces.
Description
PREPARING THE INSTALLATION
6Cima Above Ceiling ElectriScreen: Owner’s Manual
© 2015 Stewart Filmscreen Corporation
Detail A: Screen Sideview
PRODUCT DIMENSIONS
7
© 2015 Stewart Filmscreen Corporation
1. Remove the dust cover for easier access if desired.
2. Raise the screen into the ceiling.
3. Fasten the mounting brackets to the threaded rods or beams above the ceiling. (Note: The unit is usually suspended,
as shown in Figure 1, but it can be secured to the ceiling using bolts or other appropriate fasteners as well.)
4. Make sure the bottom is flush with the finished ceiling.
5. Make sure the case is level.
6. Plug in the STI wiring and terminate the power.
7. Replace the dust cover as needed.
Figure 2: Underside View IsometricFigure 1: Overhead View Isometric
RJ25 JACK
Note: A false ceiling is not intended to support the weight of a Cima Above Ceiling ElectriScreen.
♦Wear clean gloves throughout the installation process to prevent damage to the screen housing or screen
material.
♦Make sure that the screen batten never contacts or strikes any objects as damage may occur.
During installation of the Cima Above Ceiling ElectriScreen into the ceiling opening, be advised that damage
can occur to the screen. Perform the following actions to avoid damage:
Caution
Professional mounting techniques should be used. Stewart Filmscreen cannot be liable for substandard
or faulty installations.
INSTALLING THE SCREEN INTO THE CEILING
8Cima Above Ceiling ElectriScreen: Owner’s Manual
© 2015 Stewart Filmscreen Corporation
Press the "Down" button once and the Cima screen will
automatically extend fully to its pre-set limit, and then will
power itself off. Press the "Up" button once and the Cima
screen will automatically retract back into the case and
power itself off. If a custom position is desired, simply press
the "Stop" button at any time during the screen's deployment
or retraction. (See Figure 4)
Note: See page 17 for information regarding the default
limits by which the screen can be adjusted up or down from
the factory pre-set.
Operation
Making the Connections
1. Connect the RJ25 cable to the keypad.
2. Connect the other end of the RJ25 cable to the Cima unit.
Note: The maximum length of the RJ25 cable shall not exceed 50’.
Figure 4: Keypad Face
UP
DOWN
STOP
Figure 3: Keypad Connection
ADDITIONAL
RJ25 JACK FOR
OPTIONAL CONTROLS
RJ25 JACK
RJ25 JACK
KEYPAD - BACKSIDE
RJ25 CABLE
A standard 3-button low-voltage keypad is supplied for both the standard controller
and the optional Cima-Link Controller Accessories.
STANDARD CONTROL - KEYPAD CONTROL
STANDARD CONTROL - PROJECTOR CONTROL
9
© 2015 Stewart Filmscreen Corporation
When the projector is turned on or off a signal is sent to the STI-100 within the motor
and will trigger the screen to move up or down.
If there is a sudden change in direction, the motor is paused for 1/2 second before
reversing direction. This is to prevent strain on the motor mechanism, and to prevent
damage to any material controlled by the motor. Relays are automatically
de-energized after 120 seconds of operation to reduce power consumption.
How it Works
Figure 5: Projector Connection
RJ25 CABLE
Making the Connections
1. Connect the RJ25 cable to the projector.
2. Connect the other end of the RJ25 cable to the Cima unit.
Note: The maximum length of the RJ25 cable shall not exceed 50’.
ADDITIONAL
RJ25 JACK FOR
OPTIONAL CONTROLS
RJ25 JACK
10Cima Above Ceiling ElectriScreen: Owner’s Manual
© 2015 Stewart Filmscreen Corporation
When the projector is turned on or off a signal is sent to the STI-100 within the motor
and will trigger the screen to move up or down.
If there is a sudden change in direction, the motor is paused for 1/2 second before
reversing direction. This is to prevent strain on the motor mechanism, and to prevent
damage to any material controlled by the motor. Relays are automatically
de-energized after 120 seconds of operation to reduce power consumption.
Projector Operation
Press the "Down" button once and the Cima screen will automatically extend fully to
its pre-set limit, and then will power itself off. Press the "Up" button once and the
Cima screen will automatically retract back into the case and power itself off. If a
custom position is desired, simply press the "Stop" button at any time during the
screen's deployment or retraction. (See Figure 4)
Keypad Operation
Making the Connections
1. Connect the RJ25 cable splitter to the RJ25 jack in the Cima unit.
2. Connect an RJ25 cable to each jack in the splitter.
3. Connect the other end of each RJ25 cable to the jack on the projector and keypad.
Note: The maximum length of the RJ25 cable shall not exceed 50’.
Figure 6: Keypad & Projector Connection
ADDITIONAL
RJ25 JACK FOR
OPTIONAL CONTROLS
RJ25 JACK
RJ25 JACK
RJ25 CABLE
KEYPAD - BACKSIDE
RJ25 CABLE RJ25
SPLITTER
STANDARD CONTROL - KEYPAD & PROJECTOR CONTROL
Altri manuali per Above Ceiling ElectriScreen
1
Indice
Altri manuali Cima Schermo di proiezione
