Cima Below Ceiling ElectriScreen Manuale utente
TO THE INSTALLER: BE SURE TO LEAVE THIS MANUAL WITH THE OWNER.
CFS-111315-BC
To the Owner
Installation Instructions
Screen Care
Maintenance
Owner’s Manual
Below Ceiling ElectriScreen
Printed in U.S.A.
© 2015 Stewart Filmscreen Corporation
Stewart Filmscreen reserves the right to make changes to the product specified in this document.
Sizes and specifications subject to change without notice at Manufacturer’s discretion. From time to time, this
document is updated. Current versions of documentation are posted on the Stewart Filmscreen website at:
www.stewartfilmscreen.com
To the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Preparing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . 5
Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mounting the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Wall-Mounting the Screen . . . . . . . . . . . . . . . . . . . . . 7
Ceiling-Mounting the Screen . . . . . . . . . . . . . . . . . . . 8
Standard Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Keypad Control . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Projector Trigger Control . . . . . . . . . . . . . . . . . . . . . 10
Keypad & Projector Trigger Control . . . . . . . . . . . . . . . . 11
Optional Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-16
Cima-Link Infrared Package . . . . . . . . . . . . . . . . . . . . 13
Cima-Link Ethernet Package . . . . . . . . . . . . . . . . . . . 14
Cima-Link RS232 Package . . . . . . . . . . . . . . . . . . . . 15
Operating the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adjusting the Screen Extension . . . . . . . . . . . . . . . . . . . . 17-18
Adjusting the Screen Tension . . . . . . . . . . . . . . . . . . . . . . . 19
Caring for & Cleaning the Screen . . . . . . . . . . . . . . . . . . . . . 20
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
Product Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Contents
Owner’s Manual
Below Ceiling ElectriScreen
4
© 2015 Stewart Filmscreen Corporation
♦Carefully read the instructions appropriate for your needs.
♦This screen must be installed by a qualified electrician.
♦For supply connections, use wires rated for at least 75 C.
♦Use copper or aluminum conductors.
♦For indoor use only.
♦Do not connect low-voltage to line-voltage power.
♦Article 725-54(a), (1) Exception No. 3 (NEC) or Canadian CE Code Handbook, Rule
16-212, Sub Rule (4) requires segregation between line-voltage and Class 2
(low-voltage) circuits. Low-voltage / network wires should enter enclosure boxes through
separated openings. Also, conductors shall be separated by at least 1/4" or segregated
by barriers. Check with your local electrical inspector for compliance with local / national
codes and wiring practices.
♦Earth ground terminal connection must be made as shown in wiring diagrams.
♦Proper short-circuit and overload protection must be provided at the circuit breaker
distribution panel. You can use up to a 20A maximum circuit breaker with adequate
short-circuit breaking capacity for your installation.
IMPORTANT SAFETY INFORMATION
About your Cima Below Ceiling ElectriScreen
SAFETY PRECAUTIONS
The Cima Below Ceiling ElectriScreen is designed for ease of installation. The Cima
Below Ceiling features a self-finishing face-plate. There are no user-servicable parts
contained within the unit.
Congratulations on your purchase of one of our highly versatile Cima projection
screens representing “Top of the Class” in standard commercial and residential
projection screens. Please take a moment to review this manual as it will help
ensure you many years of trouble-free service from your new Cima by Stewart
Filmscreen product.
TO THE OWNER
5Cima Below Ceiling ElectriScreen: Owner’s Manual
© 2015 Stewart Filmscreen Corporation
To be installed and/or used in accordance with appropriate electrical codes and
regulations.
Caution
The Cima Below Ceiling's screen motor is pre-wired at the factory. No additional
motor assembly is required.
Motor Wiring
1. Remove the outer plastic covering and white wrapping paper surrounding the screen
case.
2. Do not remove the wrapping paper surrounding the screen roller. You should remove it
only after the unit is hung and all electrical connections have been made.
Unpacking
Note: This manual refers to “AC” to represent electrical power. Your location may
use 120 V, 220 V, or other electrical power. Screen systems are manufactured using
the electrical power type specified for the location. Use appropriate power sources
for your location.
♦Enough ladders for the personnel supporting the screen during the mounting process
♦A level
♦Fasteners appropriate for the surface on which the screen is being mounted
You will need:
During installation, do not place the unit on an unstable cart, stand, table, or
ladder. The unit may fall, causing injury and damage to the unit.
Caution
The Cima Below Ceiling product can be controlled through a number of remote
control devices, including keypads, dry contact outputs, and low-voltage trigger
outputs. With the optional Cima-Link Controller Packages, your Cima screen can be
controlled by local and remote Infrared, IP ethernet, and computer-based signaling
sources such as those manufactured by Control4, AMX, Crestron, Elan Home
Systems with RS-232-C or RS-485 interfaces.
Description
PREPARING THE INSTALLATION
6
© 2015 Stewart Filmscreen Corporation
PRODUCT DIMENSIONS
C
L
CASE & SCREEN
7Cima Below Ceiling ElectriScreen: Owner’s Manual
© 2015 Stewart Filmscreen Corporation
1. Securely install the mounting bar onto the wall, making sure the bar is level. (The preset holes in the mounting bar
are 16” apart for residential applications and 24” apart for commercial applications.)
2. Properly hang the case onto the mounting bar, making sure it is level.
Figure 3: Case with Mounting Bar - Back ViewFigure 2: Mounting Bar -
Front View (Length Varies)
Figure 1: Mounting Bar -
Side View
♦Wear clean gloves throughout the installation process to prevent damage to the screen housing or screen
material.
♦Make sure that the screen batten never contacts or strikes any objects as damage may occur.
Proper handling of the Cima Below Ceiling ElectriScreen is required during installation to avoid possible
damage to the screen. Perform the following actions to avoid damage:
Caution
Professional mounting techniques should be used. Stewart Filmscreen cannot be liable for substandard
or faulty installations.
WALL-MOUNTING THE SCREEN
8
© 2015 Stewart Filmscreen Corporation
1. Insert a provided drop-in t-bolt into each channel on the top of the case on each end (two per side) and turn
clockwise 90 degrees.
2. Place a bracket on each end of the case over the t-bolts.
3. Place a provided washer on each t-bolt and screw a provided lock nut securely onto each t-bolt.
4. Properly mount the case on the ceiling using the brackets now screwed on the case.
Detail B: Bracket DetailFigure 4: Ceiling Mounted Screen - Front View
B
Note: A false ceiling is not intended to support the weight of a Cima Below Ceiling ElectriScreen.
♦Wear clean gloves throughout the installation process to prevent damage to the screen housing or screen
material.
♦Make sure that the screen batten never contacts or strikes any objects as damage may occur.
Proper handling of the Cima Below Ceiling ElectriScreen is required during installation to avoid possible
damage to the screen. Perform the following actions to avoid damage:
Caution
Professional mounting techniques should be used. Stewart Filmscreen cannot be liable for sub-
standard or faulty installations.
CEILING-MOUNTING THE SCREEN
CHANNELS
9Cima Below Ceiling ElectriScreen: Owner’s Manual
© 2015 Stewart Filmscreen Corporation
Press the "Down" button once and the Cima screen will
automatically extend fully to its pre-set limit, and then will
power itself off. Press the "Up" button once and the Cima
screen will automatically retract back into the case and
power itself off. If a custom position is desired, simply
press the "Stop" button at any time during the screen's
deployment or retraction. (See Figure 6)
Note: See page 18 for information regarding the default
limits to which the screen can be adjusted up or down
from the factory pre-set.
Operation
Making the Connections
1. Connect the RJ25 cable to the keypad.
2. Connect the other end of the RJ25 cable to the Cima unit.
Note: The maximum length of the RJ25 cable shall not exceed 50’.
Figure 6: Keypad Face
UP
DOWN
STOP
Figure 5: Keypad Connection
SCREEN
(BACKSIDE)
ADDITIONAL
RJ25 JACK FOR
OPTIONAL CONTROLS
RJ25 JACK
RJ25 JACK
KEYPAD - BACKSIDE
RJ25 CABLE
A standard 3-button low-voltage keypad is supplied for both the standard controller
and the optional Cima-Link Controller Accessories.
STANDARD CONTROL - KEYPAD CONTROL
10
© 2015 Stewart Filmscreen Corporation
STANDARD CONTROL - PROJECTOR TRIGGER CONTROL
When the projector is turned on or off a signal is sent to the controller within the
motor and will trigger the screen to move up or down.
If there is a sudden change in direction, the motor is paused for 1/2 second before
reversing direction. This is to prevent strain on the motor mechanism, and to prevent
damage to any material controlled by the motor. Relays are automatically
de-energized after 120 seconds of operation to reduce power consumption.
How it Works
Figure 7: Projector Connection
SCREEN
(BACKSIDE)
ADDITIONAL
RJ25 JACK FOR
OPTIONAL CONTROLS
RJ25 JACK
PROJECTOR
TRIGGER CABLE
(NOT INCLUDED)
Making the Connections
1. Connect a projector trigger cable to the projector. (Note: projector trigger cable not
provided – the installer needs to make the cord from a RJ25 cord, cut one end off
and add the mono plug onsite.)
2. Connect the other end of the trigger cable to the Cima unit. (RJ25 plug)
Indice
Altri manuali Cima Schermo di proiezione
