Cisco Firepower 4100/9300 Manuale utente

Getting Started

•Task Flow, on page 1

•Initial Configuration, on page 1

•Log In or Out of the Firepower Chassis Manager, on page 8

•Accessing the FXOS CLI, on page 9

Task Flow

The following procedure shows the basic tasks that should be completed when configuring your Firepower

4100/9300 chassis.

Procedure

Step 1 Configure the Firepower 4100/9300 chassis hardware (see the Cisco Firepower Security Appliance Hardware

Installation Guide).

Step 2 Complete the initial configuration (see Initial Configuration, on page 1).

Step 3 Log in to the Firepower Chassis Manager (see Log In or Out of the Firepower Chassis Manager, on page 8).

Step 4 Set the Date and Time (see Setting the Date and Time).

Step 5 Configure a DNS server (see Configuring DNS Servers).

Step 6 Register your product license (see License Management for the ASA).

Step 7 Configure users (see User Management).

Step 8 Perform software updates as required (see Image Management).

Step 9 Configure additional platform settings (see Platform Settings).

Step 10 Configure interfaces (see Interface Management).

Step 11 Create logical devices (see Logical Devices).

Initial Configuration

Before you can use Firepower Chassis Manager or the FXOS CLI to configure and manage your system, you

must perform some initial configuration tasks. You can perform the initial configuration using the FXOS CLI

Getting Started

accessed through the console port or using SSH, HTTPS, or REST API accessed through the management

port (this procedure is also referred to as low-touch provisioning).

Initial Configuration Using Console Port

The first time that you access the Firepower 4100/9300 chassis using the FXOS CLI, you will encounter a

setup wizard that you can use to configure the system.

To repeat the initial setup, you need to erase any existing configuration using the following commands:

Firepower-chassis# connect local-mgmt

firepower-chassis(local-mgmt)# erase configuration

Note

You must specify only one IPv4 address, gateway, and subnet mask, or only one IPv6 address, gateway, and

network prefix for the single management port on the Firepower 4100/9300 chassis. You can configure either

an IPv4 or an IPv6 address for the management port IP address.

Before you begin

1. Verify the following physical connections on the Firepower 4100/9300 chassis:

• The console port is physically connected to a computer terminal or console server.

• The 1 Gbps Ethernet management port is connected to an external hub, switch, or router.

For more information, refer to the hardware installation guide.

2. Verify that the console port parameters on the computer terminal (or console server) attached to the console

port are as follows:

• 9600 baud

• 8 data bits

• No parity

• 1 stop bit

3. Gather the following information for use with the setup script:

• New admin password

• Management IP address and subnet mask

• Gateway IP address

• Subnets from which you want to allow HTTPS and SSH access

• Hostname and domain name

• DNS server IP address

Getting Started

Initial Configuration Using Console Port

Procedure

Step 1 Power on the chassis.

Step 2 Connect to the serial console port using a terminal emulator.

The Firepower 4100/9300 includes an RS-232–to–RJ-45 serial console cable. You might need to use a third

party serial-to-USB cable to make the connection. Use the following serial parameters:

• 9600 baud

• 8 data bits

• No parity

• 1 stop bit

Step 3 Complete the system configuration as prompted.

You can optionally enter the debug menu at any time during initial configuration to debug any

setup issues or abort configurations and reboot the system. To enter the debug menu, press Ctrl-C.

To exit the debug menu, press Ctrl-D twice. Note that anything you type in the interim between

pressing Ctrl-D the first time and pressing it a second time will run after the second time Ctrl-D

is pressed.

Note

Example:

---- Basic System Configuration Dialog ----

This setup utility will guide you through the basic configuration of

the system. Only minimal configuration including IP connectivity to

the FXOS Supervisor is performed through these steps.

Type Ctrl-C at any time for more options or to abort configuration

and reboot system.

To back track or make modifications to already entered values,

complete input till end of section and answer no when prompted

to apply configuration.

You have chosen to setup a new Security Appliance.

Continue? (yes/no): y

Enforce strong password? (yes/no) [y]: n

Enter the password for "admin": Farscape&32

Confirm the password for "admin": Farscape&32

Enter the system name: firepower-9300

Supervisor Mgmt IP address : 10.80.6.12

Supervisor Mgmt IPv4 netmask : 255.255.255.0

IPv4 address of the default gateway : 10.80.6.1

The system cannot be accessed via SSH if SSH Mgmt Access is not configured.

Do you want to configure SSH Mgmt Access? (yes/no) [y]: y

SSH Mgmt Access host/network address (IPv4/IPv6): 10.0.0.0

Getting Started

Initial Configuration Using Console Port

SSH Mgmt Access IPv4 netmask: 255.0.0.0

Firepower Chassis Manager cannot be accessed if HTTPS Mgmt Access is not configured.

Do you want to configure HTTPS Mgmt Access? (yes/no) [y]: y

HTTPS Mgmt Access host/network address (IPv4/IPv6): 10.0.0.0

HTTPS Mgmt Access IPv4 netmask: 255.0.0.0

Configure the DNS Server IP address? (yes/no) [n]: y

DNS IP address : 10.164.47.13

Configure the default domain name? (yes/no) [n]: y

Default domain name : cisco.com

Following configurations will be applied:

Switch Fabric=A

System Name=firepower-9300

Enforced Strong Password=no

Supervisor Mgmt IP Address=10.89.5.14

Supervisor Mgmt IP Netmask=255.255.255.192

Default Gateway=10.89.5.1

SSH Access Configured=yes

SSH IP Address=10.0.0.0

SSH IP Netmask=255.0.0.0

HTTPS Access Configured=yes

HTTPS IP Address=10.0.0.0

HTTPS IP Netmask=255.0.0.0

DNS Server=72.163.47.11

Domain Name=cisco.com

Apply and save the configuration (select 'no' if you want to re-enter)? (yes/no): y

Applying configuration. Please wait... Configuration file – Ok

.....

Cisco FPR Series Security Appliance

firepower-9300 login: admin

Password: Farscape&32

Successful login attempts for user 'admin' : 1

Cisco Firepower Extensible Operating System (FX-OS) Software

TAC support: http://www.cisco.com/tac

[...]

firepower-chassis#

Low-Touch Provisioning Using Management Port

When your Firepower 4100/9300 chassis boots up, if it does not find the startup configuration, the device

enters the Low-Touch Provisioning mode in which the device locates a Dynamic Host Control Protocol

(DHCP) server and then bootstraps itself with its management interface IP address. You can then connect

through the management interface to configure the system using SSH, HTTPS, or the FXOS REST API.

Getting Started

Low-Touch Provisioning Using Management Port

To repeat the initial setup, you need to erase any existing configuration using the following commands:

Firepower-chassis# connect local-mgmt

firepower-chassis(local-mgmt)# erase configuration

Note

You must specify only one IPv4 address, gateway, and subnet mask, or only one IPv6 address, gateway, and

network prefix for the single management port on the Firepower 4100/9300 chassis. You can configure either

an IPv4 or an IPv6 address for the management port IP address.

Before you begin

Gather the following information for use with the setup script:

• New admin password

• Management IP address and subnet mask

• Gateway IP address

• Subnets from which you want to allow HTTPS and SSH access

• Hostname and domain name

• DNS server IP address

Procedure

Step 1 Configure your DHCP server to assign an IP address to management port of the Firepower 4100/9300 chassis.

The DHCP client request from the Firepower 4100/9300 chassis will contain the following:

• The management interface’s MAC address.

• DHCP option 60 (vendor-class-identifier)—Set to “FPR9300” or “FPR4100”.

• DHCP option 61 (dhcp-client-identifier)—Set to the Firepower 4100/9300 chassis serial number. This

serial number can be found on a pull-out tab on the chassis.

Step 2 Power on the Firepower 4100/9300 chassis.

If the startup configuration is not found when the chassis boots up, the device enters the Low-Touch

Provisioning mode.

Step 3 To configure your system using HTTPS:

a) Using a supported browser, enter the following URL in the address bar:

https://<ip_address>/api

where <ip_address> is the IP address of the management port on the Firepower 4100/9300 chassis that

was assigned by your DHCP server.

For information on supported browsers, refer to the release notes for the version you are using (see

http://www.cisco.com/c/en/us/support/security/firepower-9000-series/products-release-notes-list.html).

Note

Getting Started

Low-Touch Provisioning Using Management Port

b) When prompted, log in with the username install and the password <chassis_serial_number>.

The <chassis_serial_number> can be obtained by inspecting a tag on the chassis.

c) Complete the system configuration as prompted.

• Strong password enforcement policy (for strong password guidelines, see User Accounts) .

• Password for the admin account.

• System name

• Supervisor Management IPv4 address and subnet mask, or IPv6 address and prefix.

• Default gateway IPv4 or IPv6 address.

• Host/network address and netmask/prefix from which SSH access is allowed.

• Host/network address and netmask/prefix from which HTTPS access is allowed.

• DNS Server IPv4 or IPv6 address.

• Default domain name.

d) Click Submit.

Step 4 To configure your system using SSH:

a) Connect to the management port using the following command:

ssh install@<ip_address>

where <ip_address> is the IP address of the management port on the Firepower 4100/9300 chassis that

was assigned by your DHCP server.

b) When prompted, log in with the password Admin123.

c) Complete the system configuration as prompted.

You can optionally enter the debug menu at any time during initial configuration to debug

any setup issues or abort configurations and reboot the system. To enter the debug menu,

press Ctrl-C. To exit the debug menu, press Ctrl-D twice. Note that anything you type in the

interim between pressing Ctrl-D the first time and pressing it a second time will run after the

second time Ctrl-D is pressed.

Note

Example:

---- Basic System Configuration Dialog ----

This setup utility will guide you through the basic configuration of

the system. Only minimal configuration including IP connectivity to

the FXOS Supervisor is performed through these steps.

Type Ctrl-C at any time for more options or to abort configuration

and reboot system.

To back track or make modifications to already entered values,

complete input till end of section and answer no when prompted

to apply configuration.

You have chosen to setup a new Security Appliance.

Continue? (yes/no): y

Getting Started

Low-Touch Provisioning Using Management Port

Enforce strong password? (yes/no) [y]: n

Enter the password for "admin": Farscape&32

Confirm the password for "admin": Farscape&32

Enter the system name: firepower-9300

Supervisor Mgmt IP address : 10.80.6.12

Supervisor Mgmt IPv4 netmask : 255.255.255.0

IPv4 address of the default gateway : 10.80.6.1

The system cannot be accessed via SSH if SSH Mgmt Access is not configured.

Do you want to configure SSH Mgmt Access? (yes/no) [y]: y

SSH Mgmt Access host/network address (IPv4/IPv6): 10.0.0.0

SSH Mgmt Access IPv4 netmask: 255.0.0.0

Firepower Chassis Manager cannot be accessed if HTTPS Mgmt Access is not configured.

Do you want to configure HTTPS Mgmt Access? (yes/no) [y]: y

HTTPS Mgmt Access host/network address (IPv4/IPv6): 10.0.0.0

HTTPS Mgmt Access IPv4 netmask: 255.0.0.0

Configure the DNS Server IP address? (yes/no) [n]: y

DNS IP address : 10.164.47.13

Configure the default domain name? (yes/no) [n]: y

Default domain name : cisco.com

Following configurations will be applied:

Switch Fabric=A

System Name=firepower-9300

Enforced Strong Password=no

Supervisor Mgmt IP Address=10.89.5.14

Supervisor Mgmt IP Netmask=255.255.255.192

Default Gateway=10.89.5.1

SSH Access Configured=yes

SSH IP Address=10.0.0.0

SSH IP Netmask=255.0.0.0

HTTPS Access Configured=yes

HTTPS IP Address=10.0.0.0

HTTPS IP Netmask=255.0.0.0

DNS Server=72.163.47.11

Domain Name=cisco.com

Apply and save the configuration (select 'no' if you want to re-enter)? (yes/no): y

Applying configuration. Please wait... Configuration file – Ok

.....

Initial Setup complete, Terminating sessions

.Connection to <ip_address> closed.

Step 5 To configure your system using the FXOS REST API:

Getting Started

Low-Touch Provisioning Using Management Port

Use the following examples for configuring the system using the REST API. For more information, see

https://developer.cisco.com/site/ssp/firepower/.

The attributes dns, domain_name, https_net, https_mask, ssh_net, and ssh_mask are optional.

All other attributes are mandatory for REST API configuration.

Note

IPv4 REST API example:

{

"fxosBootstrap": {

"dns": "1.1.1.1",

"domain_name": "cisco.com",

"mgmt_gw": "192.168.0.1",

"mgmt_ip": "192.168.93.3",

"mgmt_mask": "255.255.0.0",

"password1": "admin123",

"password2": "admin123",

"strong_password": "yes",

"system_name": "firepower-9300",

"https_mask": "2",

"https_net": "::",

"ssh_mask": "0",

"ssh_net": "::"

}

IPV6 REST API example

{

"fxosBootstrap": {

"dns": "2001::3434:4343",

"domain_name": "cisco.com",

"https_mask": "2",

"https_net": "::",

"mgmt_gw": "2001::1",

"mgmt_ip": "2001::2001",

"mgmt_mask": "64",

"password1": "admin123",

"password2": "admin123",

"ssh_mask": "0",

"ssh_net": "::",

"strong_password": "yes",

"system_name": "firepower-9300"

}

Before you can configure your Firepower 4100/9300 chassis using Firepower Chassis Manager, you must log

in using a valid user account. For more information on user accounts, see User Management.

You are automatically logged out of the system if a certain period of time passes without any activity. By

default, the system will log you out after 10 minutes of inactivity. To configure this timeout setting, see

Configuring the Session Timeout. You can also configure an absolute timeout setting that will log users out

Getting Started

of the system after a certain period of time even if the session is active. To configure the absolute timeout

setting, see Configuring the Absolute Session Timeout.

For a list of all system changes that cause you to be automatically logged out of Firepower Chassis Manager,

see System Changes that Cause Firepower Chassis Manager Sessions to be Closed.

You can optionally configure your Firepower Chassis Manager to allow only a certain number of unsuccessful

see Set the Maximum Number of Login Attempts.

Note

Procedure

Step 1 To log in to the Firepower Chassis Manager:

a) Using a supported browser, enter the following URL in the address bar:

https://<chassis_mgmt_ip_address>

where <chassis_mgmt_ip_address> is the IP address or host name of the Firepower 4100/9300 chassis

that you entered during initial configuration.

For information on supported browsers, refer to the release notes for the version you are using (see

http://www.cisco.com/c/en/us/support/security/firepower-9000-series/products-release-notes-list.html).

Note

b) Enter your username and password.

c) Click Login.

You are logged in and the Firepower Chassis Manager opens to show the Overview page.

Step 2 To log out of the Firepower Chassis Manager, point at your username in the navigation bar and then select

Logout.

You are logged out of the Firepower Chassis Manager and are returned to the login screen.

Accessing the FXOS CLI

You can connect to the FXOS CLI using a terminal plugged into the console port. Verify that the console port

parameters on the computer terminal (or console server) attached to the console port are as follows:

• 9600 baud

• 8 data bits

• No parity

• 1 stop bit

You can also connect to the FXOS CLI using SSH and Telnet. The FXOS supports up to eight simultaneous

SSH connections. To connect with SSH, you need to know the hostname or IP address of the Firepower

4100/9300 chassis.

Use one of the following syntax examples to log in with SSH, Telnet, or Putty:

Getting Started

Accessing the FXOS CLI

SSH log in is case-sensitive.

Note

From a Linux terminal using SSH:

•ssh ucs-auth-domain\\username@{UCSM-ip-address|UCMS-ipv6-address}

ssh ucs-example\\[email protected]

ssh ucs-example\\jsmith@2001::1

•ssh -l ucs-auth-domain\\username {UCSM-ip-address|UCSM-ipv6-address|UCSM-host-name}

ssh -l ucs-example\\jsmith 192.0.20.11

ssh -l ucs-example\\jsmith 2001::1

•ssh{UCSM-ip-address |UCSM-ipv6-address |UCSM-host-name}-lucs-auth-domain\\username

ssh 192.0.20.11 -l ucs-example\\jsmith

ssh 2001::1 -l ucs-example\\jsmith

•ssh ucs-auth-domain\\username@{UCSM-ip-address|UCSM-ipv6-address}

ssh ucs-ldap23\\[email protected]

ssh ucs-ldap23\\jsmith@2001::1

From a Linux terminal using Telnet:

Telnet is disabled by default. See Configuring Telnet for instructions on enabling Telnet.

Note

•telnet ucs-UCSM-host-name ucs-auth-domain\username

telnet ucs-qa-10

•telnet ucs-{UCSM-ip-address|UCSM-ipv6-address}ucs-auth-domain\username

telnet 10.106.19.12 2052

ucs-qa-10-A login: ucs-ldap23\blradmin

From a Putty client:

• Login as: ucs-auth-domain\username

If the default authentication is set to local, and the console authentication is set

to LDAP, you can log in to the fabric interconnect from a Putty client using

ucs-local\admin, where admin is the name of the local account.

Note

Getting Started

Accessing the FXOS CLI

Altri manuali Cisco Telaio

Cisco

Cisco CRS-1 - Carrier Routing System Router Manuale utente

Cisco

Cisco ONS 15454 Manuale utente

Cisco

Cisco NCS 4000 Series Manuale utente

Cisco

Cisco Nexus 7018 Manuale utente

Cisco

Cisco UCS 5108 Manuale del sistema

Cisco

Cisco NCS 1001 Manuale utente

Cisco

Cisco NCS 4009 Manuale di istruzioni

Cisco

Cisco NCS 4000 Series Manuale

Cisco

Cisco ASA 5508-X Manuale utente

Cisco

Cisco 6100 Guida di riferimento

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuale di servizio

Cisco

Cisco UCS S3260 Manuale utente

Cisco

Cisco C4200 Manuale utente

Cisco

Cisco USC 5030 Manuale utente

Cisco

Cisco NCS 1004 Manuale

Cisco

Cisco NCS 1010 Manuale utente

Cisco

Cisco Nexus 3000 series Manuale di istruzioni

Cisco

Cisco CRS-1 - Carrier Routing System Router Guida utente

Cisco

Cisco AS5350XM Manuale utente

Cisco

Cisco ASA5500-HW - Hardware Accessory Kit Network... Manuale

Cisco

Cisco 7513 Series Guida

Cisco

Cisco Nexus 9504 Manuale utente

Cisco

Cisco Remote PHY Shelf 7200 Manuale di istruzioni

Cisco

Cisco cBR Manuale utente

Manuali Telaio popolari di altre marche

Advantech

Advantech IPC-623 Series Manuale utente

IMC Networks

IMC Networks iMcV/18 Manuale utente

Chenbro

Chenbro RB13804N4WFT Manuale utente

Lenovo

Lenovo ThinkSystem SR665 V3 Manuale utente

Wuntronic

Wuntronic PCI4DRQ Manuale utente

EtherWAN

EtherWAN EMC400 Manuale utente

Overland Storage

Overland Storage SnapSAN S1000 Guida

Philips

Philips LC4.1E A Manuale utente

Supermicro

Supermicro SCF418 Series Manuale utente

Chenbro

Chenbro RM437 Series Manuale utente

Pickering

Pickering 40-914 Manuale utente

HP A7503-S Istruzioni per il montaggio

Supermicro

Supermicro SC823MTQ-R700LPB Manuale utente

SilverStone

SilverStone RMS08 Series Manuale utente

NI cRIO-FRC II Manuale utente

Pickering

Pickering 65-200 Manuale utente

Allied Telesis

Allied Telesis AT-MMCR18 Manuale utente

Hisense

Hisense MSD6586 Manuale utente