Cisco TelePresence System Codec C60 Manuale di istruzioni

Installing Cisco TelePresence System Codec C60

This box contains:

Codec C60

Top tray

TRC V remote control

A. Rack profiles (2 pcs)

B. Rack rear brackets (2 pcs)

C. Rack extension brackets (2 pcs)

D. Rack ear profiles (2 pcs)

Accessories box and cable kit

• HDMI cable (3m / 10ft)

• Ethernet cable (5 m / 16ft)

• Power cable (1.8 m / 6 ft)

• Batteries LR03 AAA 1.5V for the remote control

• Screwdriver, combi 2mm / 4 mm Allen Key (unbraco)

• Screws (M6 and M3) and cage nuts (M6)

• Universal rack brackets*

* Universal rack brackets: Use these only if the supplied rail based rack

mounting kit does not fit your type of rack.

User guides

The user documentation for this product, including compliance

and safety information, is available on the Cisco web site.

Go to: http://www.cisco.com/go/cseries-docs

Rack mounting

WARRANTY: Rack mounting the codec without using the

supplied mounting kit will void the warranty.

b) Snap the cage

nuts to the rack.

1Assembling the rack profiles

Slide the rack profiles A and B together. 3Mounting the rack profiles to the rack

Mount the left and right rack profiles A+B(+C) to the rack. The screws,

screwdriver and cage nuts are found in the accessories box.

2Optional: Assembling the extension rails

If the rack is deeper than the length of the

rack profiles A+B, then the extension rails C are

needed.

A+B

LEFT

RIGHT

d) On both sides:

Fasten the rack profiles A+B

together, using one M3 screw on

each side.

Tool: Screwdriver, 2 mm Allen Key

a) Mount the rack profiles in front

using two M6 screws on each side.

Tool: Screwdriver, 4 mm Allen Key

c) Mount the rack

profiles on the rear

side using the M6

knob screws.

Mount the extension rail (C) to the

rack profiles (A+B) using M6 screws.

Tool: Screwdriver, 4 mm Allen Key Details in front Details on rear side

AB BA

D D

Remote Control

A+B

Please follow the steps in

this installation guide when

rack mounting the codec.

NOTE: The profile should

be assembled with the

bend in the direction as

shown in the illustration.

NOTE: If the supplied rack profiles are incompatible

with the rack, use the supplied universal rack

brackets.

Follow the instructions in step 4 on the next page

when assembling the universal rack brackets.

Rack mounting and connecting cables

TIP

If the menu is not already present,

press Home key or OK key on the

remote control to open the menu.

Navigate in the menu with the

arrow keys.

ghi

pqrs

abc/123

jkl

tuv

abc

def

mno

wxyz

EMC Class A declaration

WARNING: This is a class A product. In a domestic environment this

product may cause radio interference in which case the user may be

required to take adequate measures.

声

明

此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种

情况下，可能需要用户对其干扰采取切实可行的措施。

WARNING: This is a class A product. In a domestic environment

this product may cause radio interference in which case the user

may be required to take adequate measures.

Installing Cisco TelePresence System Codec C60

4Assembling the rack ear profiles

Mount the rack ear profiles to the codec. 5Mounting the codec onto the rack

Locate the rails and carefully slide the codec onto the rack.

b) Fasten the codec in front

by tightening the screws on

the rack ear profiles.

Video from the camera

(HDMI to HDMI)

LAN/Ethernet Mains power

cable

Loudspeakers

(optional)

Camera control cable

(RJ45 to DSUB)

6Connecting cables

The C60 codec offers a great flexibility in connecting

audio and video equipment to the system.

a) Remove the two M3 screws on

the left and right side of the codec.

Tool: Screwdriver, 2 mm Allen Key

b) Use the same two M3 screws to

fasten the rack ear profiles to the

codec.

a) Locate the rails on the codec and the

rails on the rack. Lift the codec towards

the rack and make sure the codec enter

the rails. Carefully slide the codec into the

rack.

Power switch

After having

connected the

cables, you may

turn the codec On.

For a basic setup, you should go through these steps:

1. Connect the main camera to the HDMI 1 input using a

HDMI to HDMI cable

• For camera control you should also connect the

camera to the Camera Control input using the

dedicated cable that came with your camera (RJ45

to DSUB)

2. Connect the monitor display to the HDMI 1 output using

a HDMI to HDMI cable

3. If you want to send images from a PC, connect the PC

to the DVI-I 3 input, using a DVI to DVI or a HDMI to DVI

cable (for digital signals) or VGA to DVI cable (for analog

signals) depending on your PC’s capabilities

• Audio from the PC could be connected to Line 1

and 2 inputs for stereo signals

4. Connect the microphone to the XLR input

5. The loudspeakers should be connected to Line 1 and 2

outputs

6. Connect the codec to the IP network using the

Ethernet 1 interface

7. Connect the power and use the power switch to turn

the codec on

NOTE: If using the DVI-I out 2 for the main monitor a shortcut

is required to move the on screen display (OSD) to this

output. On the remote control key in the following sequence:

• Disconnect – *– #– *– #– 0– 2– #

PC (audio to Line In 1)

Monitor (audio from

HDMI 1 or Line Out 1-2)

Microphone

INPUTS OUTPUTS Basic setup

The main connectors for basic

setup are highlighted in orange.

1 1

IMPORTANT

There should always be a distance of

minimum 10 cm / 4in. free space in front

of the codec.

SAFETY REQUIREMENT

Make sure the codec is not mounted with

the front side up or down.

Min. 10 cm

Basic setup - The main connectors are highlighted in orange color.

Altri manuali per TelePresence System Codec C60

Altri manuali Cisco Sistema di conferenza

Cisco

Cisco TelePresence SX20 Manuale di servizio

Cisco

Cisco TelePresence System 1100 Manuale utente

Cisco

Cisco TelePresence SpeakerTrack 60 Manuale utente

Cisco

Cisco EX90 Manuale utente

Cisco

Cisco TelePresence SX20 Istruzioni originali

Cisco

Cisco Webex Room 70 Dual Manuale utente

Cisco

Cisco TelePresence System Codec C40 Manuale di servizio

Cisco

Cisco UNIFIED COMMUNICATIONS UC320W Manuale di istruzioni

Cisco

Cisco TelePresence CE9.13 Manuale utente

Cisco

Cisco BE6000 Guida

Cisco

Cisco Tandberg 1700 MXP Istruzioni per il montaggio

Cisco

Cisco EX Series Manuale utente

Cisco

Cisco EX90 Manuale utente

Cisco

Cisco Catalyst 3000 Manuale utente

Cisco

Cisco SX80 Manuale di servizio

Cisco

Cisco TelePresence SX10 Manuale utente

Cisco

Cisco TelePresence SX10 Manuale utente

Cisco

Cisco Quick Set C20 Manuale di servizio

Cisco

Cisco TelePresence SX10 Manuale utente

Cisco

Cisco TELEPRESENCE VIDEO COMMUNICATION SERVER - COMMAND REFERENCE V... Manuale operativo

Cisco

Cisco TelePresence SX10 Manuale di servizio

Cisco

Cisco MCU 5300 series Manuale utente

Cisco

Cisco EX60 Manuale utente

Cisco

Cisco TelePresence IX5200 Manuale utente

Manuali Sistema di conferenza popolari di altre marche

Kramer

Kramer VIA GO Manuale utente

AVT

AVT MAGIC AC1 Go Manuale utente

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manuale utente

Sony

Sony PCS-I150 Manuale utente

Middle Atlantic Products

Middle Atlantic Products VTC Series Manuale utente

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guida

Speakerbus

Speakerbus iD 712 Manuale utente

Trelleborg

Trelleborg SafePilot CAT PRO Manuale utente

Sennheiser

Sennheiser ADN Manuale utente

ADTRAN

ADTRAN NetVanta 7100 Manuale utente

AINA

AINA PTT Voice Responder Manuale utente

Yamaha

Yamaha ProjectPhone PJP-100H Manuale utente

vissonic

vissonic VLI Series Manuale utente

Panasonic

Panasonic KX-VC500 Manuale utente

Poly

Poly Trio 8300 Manuale utente

Crestron

Crestron Mercury CCS-UCA-SMK Disegno dimensionale

Inmarsat

Inmarsat mini M Manuale utente

Tenveo

Tenveo ALL-IN-ONE Manuale utente