Cisco ASA 5512-X Manuale utente

Cisco Systems, Inc. www.cisco.com

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide 1

Cisco ASA 5512-X, ASA 5515-X, ASA

5525-X,ASA5545-X,andASA5555-XQuick

Start Guide

Last Updated: April 27, 2017

1. Package Contents

This section lists the package contents of each chassis. Note that contents are subject to change, and your exact contents might

contain additional or fewer items.

ASA 5512-X, ASA 5515-X, or ASA 5525-X

3 4

330545

1ASA 5512-X, ASA 5515-X, or ASA 5525-X Chassis 2BlueConsoleCableandSerialPCTerminal Adapter

(DB-9 to RJ-45)

3Power Cord 4Power Cord Retainer

54 10-32 Phillips Screws for rack mounting 64 12-24 Phillips Screws for rack mounting

74 M6 Phillips Screws for rack mounting

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide

2. License Requirements

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide 2

ASA 5545-X and ASA 5555-X

2. License Requirements

ASA Licenses

The ASA 5506-X includes the Base or Security Plus license, depending on the version you ordered. It also comes pre-installed with

the Strong Encryption (3DES/AES) license if you qualify for its use. You can optionally purchase an AnyConnect Plus or Apex

license.

If you need to manually request the Strong Encryption license (which is free), see http://www.cisco.com/go/license.

If you want to upgrade from the Base license to the Security Plus license, or purchase an AnyConnect license, see

http://www.cisco.com/go/ccw. See also the Cisco AnyConnect Ordering Guide and the AnyConnect Licensing Frequently Asked

Questions (FAQ). You will then receive an email with a Product Authorization Key (PAK) so you can obtain the license activation

key. For the AnyConnect licenses, you receive a multi-use PAK that you can apply to multiple ASAs that use the same pool of user

sessions.

Note: The serial number used for licensing is different from the chassis serial number printed on the outside of your hardware. The

chassis serial number is used for technical support, but not for licensing. To view the licensing serial number, enter theshow version

| grep Serial command or see the ASDM Configuration > Device Management > Licensing Activation Key page.

ASA FirePOWER Licenses

The ASA FirePOWER module uses a separate licensing mechanism from the ASA. No licenses are pre-installed, but the box

includes a PAK on a printout that lets you obtain a license activation key for the following licenses:

Control and Protection—Control is also known as “Application Visibility and Control (AVC)” or “Apps”. Protection is also

known as “IPS”. In addition to the activation key for these licenses, you also need “right-to-use” subscriptions for automated

updates for these features.

The Control (AVC) updates are included with a Cisco support contract.

330544

1ASA 5545-X or ASA 5555-X Chassis (one

power supply shown) 2Blue Console Cable and Serial PC Terminal Adapter

(DB-9 to RJ-45)

3Power Cord 4Power Cord Retainer

5Slide Rail Kit

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide

3. Power On the ASA

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide 3

The Protection (IPS) updates require you to purchase the IPS subscription from http://www.cisco.com/go/ccw. This

subscription includes entitlement to Rule, Engine, Vulnerability, and Geolocation updates. Note: This right-to-use subscription

does not generate or require a PAK/license activation key for the ASA FirePOWER module; it just provides the right to use the

updates.

Other licenses that you can purchase include the following:

Advanced Malware Protection (AMP)

URL Filtering

These licenses do generate a PAK/license activation key for the ASA FirePOWER module. See the Cisco Firepower System Feature

Licenses for more information.

To install the Control and Protection licenses and other optional licenses, see Install the Licenses, page 12.

3. Power On the ASA

1. Attach the power cable to the ASA and connect it to an electrical outlet.

The power turns on automatically when you plug in the power cable; do not press the power button on the front panel. (For

older models, the power does not turn on automatically; check the hardware installation guide for more information).

2. Check the Power LED on the front of the ASA; if it is solid green, the device is powered on.

3. Check the Status LED on the front of the ASA; after it is solid green, the system has passed power-on diagnostics.

4. Modify the Initial Configuration for the ASA FirePOWER

Module (Optional)

The ASA ships with a default configuration that enables Adaptive Security Device Manager (ASDM) connectivity to the

Management 0/0 interface. When you use a software module such as the ASA FirePOWER module, we recommend that you do

not use the default configuration, which can preclude the ASA FirePOWER module from reaching the Internet for updates. This

section describes how to apply a new configuration so the ASA FirePOWER can access the Internet. This configuration also enables

a basic usable configuration for an inside and outside network.

ASA 9.7 and Later

The following figure shows the recommended network deployment for the ASA 5500-X with the ASA FirePOWER module. This

deployment includes an inside bridge group that includes all but the outside interface so you can use these interfaces as an alternative

to an external switch.

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide

4. Modify the Initial Configuration for the ASA FirePOWER Module (Optional)

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide 4

Note: The ASA 5525-X, 5545-X, and 5555-X include interfaces GigabitEthernet 0/0 through GigabitEthernet 0/7.

This procedure lets you connect to the ASA console port and paste in a new configuration that configures the following behavior:

outside GigabitEthernet 0/0, IP address from DHCP

inside bridge group with GigabitEthernet 0/1 through 0/5 (or through 0/7 for the ASA 5525-X, 5545-X, and 5555-X) member

interfaces, 192.168.1.1

inside --> outside traffic flow

inside --> inside traffic flow for member interfaces

DHCP for clients on inside

Management 0/0 belongs to the ASA FirePOWER module. The interface is Up, but otherwise unconfigured on the ASA. The

ASA FirePOWER module can then use this interface to access the ASA inside network and use the inside interface as the

gateway to the Internet.

Note: Do not configure an IP address for this interface in the ASA configuration. Only configure an IP address in the

FirePOWER configuration. You should consider this interface as completely separate from the ASA in terms of routing.

ASDM access on the inside interface

NAT: Interface PAT for all traffic from inside and management to outside.

Note: If you want to deploy a separate router on the inside network, then you can route between management and inside. In this

case, you can manage both the ASA and ASA FirePOWER module on Management 0/0 with the appropriate configuration changes.

outside

GigabitEthernet 0/0

(DHCP)

inside

BVI 1

192.168.1.1

inside1

GigabitEthernet 0/1

inside3 - inside5

GigabitEthernet 0/3

- GigabitEthernet 0/5

inside2

GigabitEthernet 0/2

Internet

Management 1/1

No ASA IP address

ASA FirePOWER IP address: 192.168.1.2

ASA FirePOWER

Default Gateway

Direct Cable

Connection between

Management 0/0 and

GigabitEthernet 0/1

Management

Computer

- Gigab

bitEthernet 0

bitEtherne

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide

4. Modify the Initial Configuration for the ASA FirePOWER Module (Optional)

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide 5

Procedure

1. Connect your computer to the ASA console port with the supplied console cable. You might need to use a third party

serial-to-USB cable to make the connection.

2. Launch a terminal emulator and connect to the ASA.

3. Press the Enter key to see the following prompt:

ciscoasa>

4. Access privileged EXEC mode:

enable

The following prompt appears:

Password:

5. Press Enter. By default, the password is blank.

6. Access global configuration mode:

configure terminal

7. Clear the configuration:

clear configure all

8. Copy and paste the following configuration at the prompt. Omit commands with GigabitEthernet0/6 and GigabitEthernet0/7

and inside_6 and inside_7 for the ASA 5512-X and 5515-X.

interface Management0/0

no shutdown

interface GigabitEthernet0/0

nameif outside

security-level 0

ip address dhcp setroute

no shutdown

interface bvi 1

nameif inside

security-level 100

ip address 192.168.1.1 255.255.255.0

no shutdown

interface GigabitEthernet0/1

nameif inside_1

security-level 100

bridge-group 1

no shutdown

interface GigabitEthernet0/2

nameif inside_2

security-level 100

no shutdown

bridge-group 1

interface GigabitEthernet0/3

nameif inside_3

security-level 100

no shutdown

bridge-group 1

interface GigabitEthernet0/4

nameif inside_4

security-level 100

no shutdown

bridge-group 1

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide

4. Modify the Initial Configuration for the ASA FirePOWER Module (Optional)

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide 6

interface GigabitEthernet0/5

nameif inside_5

security-level 100

no shutdown

bridge-group 1

interface GigabitEthernet0/6

nameif inside_6

security-level 100

no shutdown

bridge-group 1

interface GigabitEthernet0/7

nameif inside_7

security-level 100

no shutdown

bridge-group 1

object network obj_any1

subnet 0.0.0.0 0.0.0.0

nat (inside_1,outside) dynamic interface

object network obj_any2

subnet 0.0.0.0 0.0.0.0

nat (inside_2,outside) dynamic interface

object network obj_any3

subnet 0.0.0.0 0.0.0.0

nat (inside_3,outside) dynamic interface

object network obj_any4

subnet 0.0.0.0 0.0.0.0

nat (inside_4,outside) dynamic interface

object network obj_any5

subnet 0.0.0.0 0.0.0.0

nat (inside_5,outside) dynamic interface

object network obj_any6

subnet 0.0.0.0 0.0.0.0

nat (inside_6,outside) dynamic interface

object network obj_any7

subnet 0.0.0.0 0.0.0.0

nat (inside_7,outside) dynamic interface

same-security-traffic permit inter-interface

http server enable

http 192.168.1.0 255.255.255.0 inside_1

http 192.168.1.0 255.255.255.0 inside_2

http 192.168.1.0 255.255.255.0 inside_3

http 192.168.1.0 255.255.255.0 inside_4

http 192.168.1.0 255.255.255.0 inside_5

http 192.168.1.0 255.255.255.0 inside_6

http 192.168.1.0 255.255.255.0 inside_7

dhcpd auto_config outside

dhcpd address 192.168.1.5-192.168.1.254 inside

dhcpd enable inside

logging asdm informational

9. Save the new configuration:

write memory

10. Cable the following:

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide

4. Modify the Initial Configuration for the ASA FirePOWER Module (Optional)

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide 7

a. Cable Management 0/0 (for the ASA FirePOWER module) directly to one of: GigabitEthernet 0/1 through GigabitEthernet

0/5 (through 0/7 for the ASA 5525-X, 5545-X, and 5555-X).

Note: You can connect inside and management on the same network because the management interface acts like a separate

device that belongs only to the ASA FirePOWER module.

b. Cable your computer to one of: GigabitEthernet 0/1 through GigabitEthernet 0/5 (through 0/7 for the ASA 5525-X, 5545-X,

and 5555-X).

c. Cable GigabitEthernet 0/0 (outside) to your WAN device, for example, your cable modem.

Note: If the cable modem supplies an outside IP address that is on 192.168.1.0/24 or 192.168.10.0/24, then you must change

the ASA configuration to use a different IP address. Interface IP addresses, HTTPS (ASDM) access, and DHCP server settings

can all be changed using the Startup Wizard. If you change the IP address to which you are connected to ASDM, you will be

disconnected when you finish the wizard. You must reconnect to the new IP address.

ASA 9.6 and Earlier

The following figure shows the suggested network deployment for the ASA 5500-X with the ASA FirePOWER module:

WAN Modem

GigabitEthernet 0/1-0/5 Bridge Group

inside, 192.168.1.1

Internet

Management Computer

DHCP from inside: 192.168.1.x

GigabitEthernet 0/0

outside, DHCP from Modem

Management 0/0

192.168.1.2

(FirePOWER management)

Management PC

Layer 2

Switch

ASA

inside

Management 0/0

No ASA IP address

Module IP address: 192.168.1.2

outside

Module Default Gateway

GigabitEthernet 0/1

192.168.1.1

GigabitEthernet 0/0

Module

Internet

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide

4. Modify the Initial Configuration for the ASA FirePOWER Module (Optional)

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide 8

Note: If you have an inside router instead of a switch, you can skip this section and instead configure the ASA to route between

management and an inside network. In this case, configure the ASA and the ASA FirePOWER Management 0/0 IP addresses to be

on the same network. Be sure to configure appropriate routes on the ASA and on the ASA FirePOWER so the management network

can reach the inside network, and vice versa.

This procedure lets you connect to the ASA console port and paste in a new configuration that configures the following behavior:

inside --> outside traffic flow

outside IP address from DHCP

DHCP for clients on inside

Management 0/0 belongs to the ASA FirePOWER module. The interface is Up, but otherwise unconfigured on the ASA. The

ASA FirePOWER can then use this interface to access the ASA inside network and use the inside interface as the gateway to

the Internet.

Note: Do not configure an IP address for this interface in the ASA configuration. Only configure an IP address in the module

configuration. You should consider this interface as completely separate from the ASA in terms of routing.

ASDM access on the inside interface

To achieve the above configuration, perform the following steps.

Procedure

1. Connect your computer to the ASA console port with the supplied console cable. You might need to use a third party

serial-to-USB cable to make the connection.

2. Launch a terminal emulator and connect to the ASA.

3. Press the Enter key to see the following prompt:

ciscoasa>

4. Access privileged EXEC mode:

enable

The following prompt appears:

Password:

5. Press Enter. By default, the password is blank.

6. Access global configuration mode:

configure terminal

7. Clear the configuration:

clear configure all

8. Copy and paste the following configuration at the prompt:

interface management0/0

no shutdown

interface gigabitethernet0/0

nameif outside

ip address dhcp setroute

no shutdown

interface gigabitethernet0/1

nameif inside

ip address 192.168.1.1 255.255.255.0

security-level 100

no shutdown

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide

4. Modify the Initial Configuration for the ASA FirePOWER Module (Optional)

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide 9

object network obj_any

subnet 0 0

nat (any,outside) dynamic interface

http server enable

http 192.168.1.0 255.255.255.0 inside

dhcpd address 192.168.1.5-192.168.1.254 inside

dhcpd auto_config outside

dhcpd enable inside

logging asdm informational

9. Save the new configuration:

write memory

1. Cable the following:

a. Cable the following to a Layer 2 Ethernet switch:

—GigabitEthernet 0/1 interface (inside)

—Management 0/0 interface (for the module)

—Your computer

Note: You can connect inside and management on the same network because the management interface acts like a separate

device that belongs only to the ASA FirePOWER module.

b. Connect the outside GigabitEthernet 0/0 interface to your upstream router or WAN device.

Note: If the cable modem supplies an outside IP address that is on 192.168.1.0/24 or 192.168.10.0/24, then you must change

the ASA configuration to use a different IP address. Interface IP addresses, HTTPS (ASDM) access, and DHCP server settings

can all be changed using the Startup Wizard. If you change the IP address to which you are connected to ASDM, you will be

disconnected when you finish the wizard. You must reconnect to the new IP address.

GigabitEthernet 0/0

outside, DHCP from modem

Management 0/0

192.168.1.2

(Module management)

Layer 2 Switch

WAN Modem

Management Computer

DHCP from ASA: 192.168.1.x

GigabitEthernet 0/1

inside, 192.168.1.1

(ASA management; Gateway)

Internet

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide

5. Launch ASDM

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X Quick Start Guide 10

5. Launch ASDM

See the ASDM release notes on Cisco.com for the requirements to run ASDM.

This procedure assumes you want to use ASDM to manage the ASA FirePOWER Module. If you want to use the Firepower

Management Center, then you need to connect to the module CLI and run the setup script; see the ASA FirePOWER quick start

guide.

Procedure

1. On the computer connected to the ASA, launch a web browser.

2. In the Address field, enter the following URL: https://192.168.1.1/admin. The Cisco ASDM web page appears.

3. Click one of the available options: Install ASDM Launcher, Run ASDM, or Run Startup Wizard.

4. Follow the onscreen instructions to launch ASDM according to the option you chose. The Cisco ASDM-IDM Launcher

appears.

If you click Install ASDM Launcher, in some cases you need to install an identity certificate for the ASA and a separate

certificate for the ASA FirePOWER module according to Install an Identity Certificate for ASDM.

5. Leave the username and password fields empty, and click OK. The main ASDM window appears.

6. If you are prompted to provide the IP address of the installed ASA FirePOWER module, cancel out of the dialog box. You must

first set the module IP address to the correct IP address using the Startup Wizard.

ASDM can change the ASA FirePOWER module IP address settings over the ASA backplane; but for ASDM to then manage

the module, ASDM must be able to reach the module (and its new IP address) on the Management 0/0 interface over the

network. The recommended deployment allows this access because the module IP address is on the inside network. If ASDM

cannot reach the module on the network after you set the IP address, then you will see an error.

7. Choose Wizards > Startup Wizard.

8. Configure additional ASA settings as desired, or skip screens until you reach the ASA FirePOWER Basic Configuration

screen.

Altri manuali per ASA 5512-X

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Firewall

Cisco

Cisco Firepower 1100 Manuale utente

Cisco

Cisco 515E - PIX Restricted Bundle Manuale utente

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuale utente

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuale

Cisco

Cisco IronPort M1070 Manuale utente

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuale utente

Cisco

Cisco Firepower 7010, Firepower 7020, Firepower 7030, Firepower 7050, Firepower 7110, Firepower 7120, Firepower 7115, Firepower... Manuale utente

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuale utente

Cisco

Cisco 5510 - ASA SSL / IPsec VPN Edition Manuale utente

Cisco

Cisco 5580-40 - ASA Firewall Edition Manuale

Cisco

Cisco PIX 506E - Security Appliance Manuale utente

Cisco

Cisco CSA 90 Series Manuale del prodotto

Cisco

Cisco 3110 Manuale

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuale utente

Cisco

Cisco ASA 5506-X Manuale utente

Cisco

Cisco RV110W Manuale utente

Cisco

Cisco Firepower 4100 Series Manuale utente

Cisco

Cisco ISA 3000 Manuale utente

Cisco

Cisco IPS-4255-K9 - Intrusion Protection Sys 4255 Manuale utente

Cisco

Cisco Firepower 4100 Series Manuale di installazione

Cisco

Cisco ASA 5506-X Istruzioni per l'installazione

Cisco

Cisco ASA 5580 Manuale utente

Cisco

Cisco PIX-515E Manuale utente

Cisco

Cisco LightStream 1010 Manuale utente

Manuali Firewall popolari di altre marche

Fortinet

Fortinet FortiGate Voice Series Manuale utente

ADTRAN

ADTRAN NetVanta 2300 Manuale utente

SecureLogix

SecureLogix ETM System Manuale utente

NETGEAR

NETGEAR ProSafe FVX538 Manuale utente

Lanner

Lanner FW-8877 Manuale utente

Huawei

Huawei USG6000 Series Manuale di installazione e funzionamento

H3C

H3C SecPath F5000-AI-15 Manuale utente

Nexcom

Nexcom DNA 1150 Manuale utente

Fortinet

Fortinet FortiGate-60 series Manuale utente

Draytek

Draytek Vigor2860 Series Manuale utente

Lanner electronics

Lanner electronics FW-7650 Series Manuale utente

Swisscom

Swisscom Internet Backup Manuale utente

SonicWALL

SonicWALL NSa 5700 Manuale utente

DPtech

DPtech FW1000 SERIES Manuale utente

FEITIAN

FEITIAN MultiPass FIDO Manuale utente

EBLOCKER

EBLOCKER PRO Manuale utente

GTA

GTA GB-200 Manuale utente

Trend Micro

Trend Micro Deep Edge Manuale utente