Cisco Network Analysis Module 6000 Manuale utente

CHAPTER

2-1

Cisco Video Surveillance 6000P IP Camera Installation Guide

OL-28118-01

Camera Installation

This chapter provides information and instructions for installing the Cisco Video Surveillance

6000P IP Camera, and includes the following topics:

•Installation Guidelines, page 2-1

•Warnings Before Installation, page 2-1

•Installing the IP Camera, page 2-4

Installation Guidelines

This section describes how to install the IP camera. Before installing, review these guidelines:

•The IP camera requires a network cable and a connection to a standard 10/100BaseT router or

switch. To power the IP camera with Power over Ethernet (PoE), a switch must be 802.3af

compliant.

•If you are using the IP camera on a network connection that does not provide PoE, you must use a

Cisco 12 VDC power adapter (Cisco part number CIVS-PWRPAC-12V) or a third-party 24 VAC

power adapter.

•If you are using an input device, output device, or pan/tilt control device, you must configure

additional settings after installing and performing the initial set up of the IP camera before the

external device can fully operate. For detailed information about these settings, see the Cisco Video

Surveillance 6000 Series IP Camera Configuration Guide.

•If you do not connect an external device (input, output, or pan/tilt control) when you perform the

following installation procedure, you can install any of these devices later.

Warnings Before Installation

•Power off the Network Camera as soon as

smoke or unusual odors are detected.

Contact your distributor in the event of this

happening.

•Keep the Network Camera away from

water. If the Network Camera becomes wet,

power off immediately.

Contact your distributor in the event of this

happening.

2-2

Cisco Video Surveillance 6000P IP Camera Installation Guide

OL-28118-01

Chapter 2 Camera Installation

Warnings Before Installation

•Do not place the Network Camera around

heat sources, such as a television or oven.

•Refer to your user's manual for the

operating temperature.

•Keep the Network Camera away from

direct sunlight.

•Do not place the Network Camera in high

humidity environments.

•Do not place the Network Camera on

unsteady surfaces.

•Do not touch the Network Camera during a

lightning storm.

2-3

Cisco Video Surveillance 6000P IP Camera Installation Guide

OL-28118-01

Chapter 2 Camera Installation

Warnings Before Installation

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

The power supply must be placed indoors.

Statement 331

Note If you use the IP camera outdoors, place the camera and the power supply in a suitable NEMA

enclosure.

Warning

This product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source

or an IEC60950 compliant limited power source.

Statement 353

Caution Inline power circuits provide current through the communication cable. Use the Cisco provided cable or

a minimum 24AWG communication cable.

Note The power adapter that you use with the IP camera must provide power that is within +/–10% of the

required power.

Note The equipment is to be connected to a Listed class 2, limited power source.

•Do not disassemble the Network Camera. •Do not drop the Network Camera.

•Do not insert sharp or tiny objects into the

Network Camera.

2-4

Cisco Video Surveillance 6000P IP Camera Installation Guide

OL-28118-01

Chapter 2 Camera Installation

Installing the IP Camera

To install the Cisco Video Surveillance 6000P IP Camera, perform the following steps:

Procedure

Step 1 Turn the lens clockwise into the lens opening until it stops (see Figure 2-1). If necessary, turn it

counterclockwise slowly until it gets the best attitude. The IP camera accepts CS-mount lenses with a

lens protrusion of up to 5 mm.

Figure 2-1 Mounting the IP Camera Lens

Ensure that the lens is clean because any dirt may degrade the quality of video images.

Note Save the lens opening dust cap and replace the dust cap if you remove the lens.

Step 2 Connect the P-iris lens cable to the P-iris lens connector on the back of the IP camera (see Figure 2-2).

Figure 2-2 Mounting the IP Camera Lens

Step 3 Optional. Use the GPIO terminal block ports on the back of the IP camera to connect an external device

that triggers alarms (connect through input port) or responds to alarms (connect through output port).

Figure 2-3 shows the GPIO terminal block pin locations and descriptions.

2-5

Cisco Video Surveillance 6000P IP Camera Installation Guide

OL-28118-01

Chapter 2 Camera Installation

Installing the IP Camera

Figure 2-3 GPIO Terminal Block Pin Locations and Descriptions

Step 4 Connect an STP (shielded twisted pair) Category 5 or higher network cable to the LAN port on the back

of the camera and to a 10/100/BaseT router or switch.

If your network provides PoE, the IP camera powers on. Skip to Step 6.

Step 5 If you are using the IP camera on a network connection that does not provide PoE, connect a 12 VDC

power adapter to the camera using the provided power connector.

Step 6 Wait for the camera to boot and check the LEDs on the IP camera.

•The red status LED lights steadily.

•The green network LED blinks repeatedly.

Step 7 Mount the IP camera in the desired location.

Connect the mounting device to the threaded mounting hole on the bottom or top of the IP camera,

depending on your installation requirement.

Step 8 Optional. Use mini cable with BNC connector to temporarily attach an NTSC or PAL compliant analog

video display device to the analog video out port on the rear of the camera and adjust the IP camera field

of view.

Note The mini cable with BNC adapter is included in the audio/video cables accessory kit, which you can

purchase from Cisco (Cisco part number CIVS-IPCA-1021= ).

Analog video is enabled by default to allow you to adjust the camera field of view during installation.

However, it is not supported as a normal camera feed and is automatically disabled when any of the

following camera settings are made:

•The primary video stream frame rate is set higher than 15 fps.

•The secondary video stream is enabled.

Note We recommend that you disable analog video after installation. To disable analog video, see the Cisco

Video Surveillance 6000 Series IP Camera Configuration Guide.

After you install the IP camera, follow the instructions in Chapter 3, “Performing the Initial Setup of the

IP Camera” to access and configure the camera.

Pin Description

1Power+12V

2 Digital Output

3 Digital Input

4Ground

5 AC 24V Input

6 AC 24V Input

7 RS-485+

8 RS-485–

87654321

2-6

Cisco Video Surveillance 6000P IP Camera Installation Guide

OL-28118-01

Chapter 2 Camera Installation

Installing the IP Camera

Altri manuali per Network Analysis Module 6000

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Telecamera IP

Cisco

Cisco 2500 Series Manuale utente

Cisco

Cisco Webex Desk Manuale utente

Cisco

Cisco PVC300 - Small Business Pan Tilt Optical Zoom Internet Camera... Manuale di istruzioni

Cisco

Cisco PrecisionHD 1080p12x Manuale utente

Cisco

Cisco 7030 Manuale utente

Cisco

Cisco Linksys WVC210 Manuale utente

Cisco

Cisco CIVS-IPC-2500 Manuale utente

Cisco

Cisco 6400E Manuale utente

Cisco

Cisco CIVS-IPC-4300 Manuale utente

Cisco

Cisco Video Surveillance 3520 Manuale utente

Cisco

Cisco PVC300 - Small Business Pan Tilt Optical Zoom Internet Camera... Manuale utente

Cisco

Cisco 2800 Series Manuale utente

Cisco

Cisco 2600 Series Manuale utente

Cisco

Cisco CIVS-IPC-2621V Manuale utente

Cisco

Cisco PrecisionHD 4X CTS-PHD-1080P4XS1 Istruzioni operative

Cisco

Cisco PrecisionHD 1080p12x Manuale di istruzioni

Cisco

Cisco Video Surveillance 2621 IP Dome Manuale utente

Cisco

Cisco Nexus 5010 Manuale utente

Cisco

Cisco 6000P Manuale utente

Cisco

Cisco CIVS-IPC-2500W - Video Surveillance IP Camera... Manuale utente

Cisco

Cisco Unity Client 4.0 Manuale utente

Cisco

Cisco 6500PD Manuale utente

Cisco

Cisco CIVS-IPC-6400 Manuale utente

Cisco

Cisco 6400 Manuale utente

Manuali Telecamera IP popolari di altre marche

FLIR

FLIR Exx series Manuale utente

Avigilon

Avigilon H4A-BO1-IR Manuale utente

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuale utente

ShareTech

ShareTech AV1 Manuale utente

Ezviz

Ezviz C6C Manuale utente

Melchioni

Melchioni UCAM 2015 Manuale utente

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuale utente

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuale utente

Mitel

Mitel 6800i Series Manuale di servizio

Vitek

Vitek VTC-IR403-212NP Manuale utente

THOMSON

THOMSON DSC - 323W Manuale utente

AVer

AVer FB2027 Manuale utente

ENFORCER

ENFORCER EV-T5105-N2SQ Manuale utente

Wansview

Wansview NC543 Manuale utente

Eneo

Eneo MCB-64A0003M0A Manuale utente

deView electronics

deView electronics CBDNI36F Manuale utente

Swann

Swann SwannEye Manuale utente

LevelOne

LevelOne IP CamSecure Manuale utente