Cisco Edge 300 Series Guida rapida

Last updated on October 15, 2015

Edge300FirmwareUpgrade

Introduction

This guide outlines the steps to upgrade the firmware on the Cisco Edge 300 and will be described in two

stages:

Preparing a bootable USB drive containing the desired Edge 300 firmware

Flashing the firmware onto the Edge 300 device

Prerequisites

Cisco Edge 300 device

1 USB flash drive formatted in FAT32 file system (minimum 2GB free space)

1 Edge 300 firmware image file (for use with the USB flash drive)

1 paper clip / SIM eject tool (for the recessed reset button)

Note:

Empty the contents of the USB flash drive for the purpose of Edge firmware flashing. The process

of creating a bootable flash drive will temporarily render it unusable for conventional storage and

transferring of files. The flash drive can later be reformatted back to its original file system once the

firmware upgrade has completed.

PreparingaBootableUSBDrive

1. From your computer, copy the Edge 300 firmware image into the root directory of the USB flash

drive. Disconnect the USB drive from your computer and connect it to the USB port of the Edge 300,

located on the side of the device.

2. SSH into the device using either PuTTy (on a Windows PC) or Terminal (on a Mac) using the

commands shown below. Replace {device IP} with the actual IP address of the Edge device. (verify

with your network administrator regarding the correct IP address and root credentials for the Edge

300).

3. Use the blkid command to locate the USB drive. (usually /dev/sdxx with xx being b1, b2 or c1, c2

etc.) For this guide, we will assume it is /dev/sdb1.

4. Mount the USB drive.

5. Unmount the USB drive. Copy the firmware image onto the Edge 300 device (into the /apps/

directory). Wait for the task to finish. The copying of the image file will be completed when the

console displays a # symbol at the beginning of the command line.

6. Without ejecting your USB drive, run the following commands (remember to replace sdb1 with your

blkid if discovered to be different from Step 3). Note that each command will take some time to

execute. Wait until each command has completed (console displays a #) before proceeding to the

next command. When all commands have been executed, remove the USB drive from the device.

#sshroot@{deviceIP}

#root@{deviceIP}password:cisco

#blkid

/dev/sdb1:LABEL="USBDRIVE"UUID="7288-0792"TYPE="vfat"

#mount/dev/sdb1/tmp/mnt

#cp/tmp/mnt/smi-usb-sunbird-1.5.0-delivery.tar.gz/apps/

#umount/tmp/mnt

FlashingtheFirmware

1. Press and hold the power button on the Edge 300 to turn it OFF. Connect the newly created

bootable USB drive into the USB port again, located on the side of the device.

2. Press and hold the power button on the Edge 300 to turn it back ON. Using your paper clip / SIM

eject tool, press and hold the reset button located next to the power button of the device for about 5

seconds until the device reboots itself.

#mkfs.ext3/dev/sdb1

#mount/dev/sdb1/tmp/mnt

#tarxvzf/apps/smi-usb-sunbird-1.5.0-delivery.tar.gz–C/tmp/mnt/

#umount/tmp/mnt

3. Once rebooted, the Edge 300 device will read the contents of the USB drive and begin flashing the

firmware. The power LED will be flashing continuously at this point, indicating the firmware update is

in process. The firmware flashing will be completed when you are able to view the login screen on a

connected display.

© 2018 Appspace Inc. All Rights Reserved | Legal | Give Feedback

Altri manuali per Edge 300 Series

1

Indice

Altri manuali Cisco Hardware di rete

Cisco

Cisco GS7000 Guida

Cisco

Cisco Meraki Catalyst 9300/X/L-M Series Manuale utente

Cisco

Cisco CVPN3015-NR - VPN Concentrator 3015 Manuale utente

Cisco

Cisco Aironet 1040 Series Manuale utente

Cisco

Cisco ONS 15327 Manuale

Cisco

Cisco Mc3810 - 16MB Flash Memory Guida rapida

Cisco

Cisco AIR-BR350-A-K9 - Aironet 350 Wireless Bridge Manuale

Cisco

Cisco ONS 15454 Manuale di istruzioni

Cisco

Cisco OL-7822-06 Manuale utente

Cisco

Cisco Remote PHY Shelf 7200 Manuale di installazione

Cisco

Cisco Network Adapter VIP-FE-TX/4E Manuale dell'operatore

Cisco

Cisco SCE8000 GBE Manuale utente

Cisco

Cisco CRS-1 - Carrier Routing System Router Guida utente

Cisco

Cisco ASR 9000 Series Manuale utente

Cisco

Cisco Nexus 93600CD-GX Manuale

Cisco

Cisco NCS 2002 Manuale di istruzioni

Cisco

Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - Manuale utente

Cisco

Cisco ASR 5000 Manuale utente

Cisco

Cisco MultiRIP Ethernet Card Manuale utente

Cisco

Cisco WEC600N Manuale utente

Cisco

Cisco NCS 1001 Manuale

Cisco

Cisco NCS 540 Manuale utente

Cisco

Cisco IDS-4230-FE - Intrusion Detection Sys Fast Ethernet... Manuale dell'operatore

Cisco

Cisco NM-1FE-TX - Interface Module Ethernet Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente