Cisco VSVM Manuale di istruzioni
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Installing and Upgrading Cisco Video
Surveillance Virtual Matrix (VSVM)
Contents
This document provides the following information and instructions:
Installation and Initial Configuration:
1. Verify minimum system requirements—System Requirements, page 2
2. Understand general installation information—Installing VSVM, page 4
3. Obtain the VSVM software—Obtaining VSVM Software, page 3
4. Install the VSVM software—Installing VSVM, page 4
5. Configure video repositories for archives and clips—Configuring VSVM,
page 5
After installation:
6. (As needed) Upgrade VSVM to a new software release—Upgrading VSVM,
page 5
System Requirements
2
Installing and Upgrading Cisco Video Surveillance Virtual Matrix (VSVM)
System Requirements
This section describes the requirements of the server and client systems on which
you install VSVM.
The server must meet the following minimum requirements:
• Hardware
–
Intel Celeron or Pentium, 1.7 GHz
–
1 GB DRAM
–
10 GB hard disk
• Operating System (one of the following):
–
Red Hat Enterprise 4 Update 2 (RHEL4)
–
SuSE Enterprise 9 Service Pack 3 (SLES9-SP3)
–
SuSE Enterprise 10 Service Pack 1 (SLES10-SP1)
–
SuSE Enterprise 10 Service Pack 1 64-bit (SLES10-SP1-64)
• Software License Key
–
Obtain a VSVM license key by contacting vsm-license@cisco.com
A client PC must meet the following minimum requirements:
• Hardware
–
1.7 GHz Pentium III if running 1 video window
–
1.7 GHz Pentium 4 if running 2 video windows
–
3.2 GHz Pentium 4 with hyperthreading enabled if running 4 video
windows
–
1 GB DRAM
–
ATI or Nvidia DirectX 9 compatible graphics interface. The graphics
interface and Drivers must support DirectX Acceleration, Direct3D
Acceleration, and AGP texture acceleration and have at least 128 MB of
video memory.
• Operating system:
–
Microsoft Windows XP SP2 (32-bit)
3
Installing and Upgrading Cisco Video Surveillance Virtual Matrix (VSVM)
Installation Notes
• Software:
–
Microsoft Internet Explorer 6.0
–
Microsoft DirectX 9.0c
Installation Notes
• The Pegasus MJPEG video decoder is installed automatically with the VSVM
client.
• Cisco recommends that you use NTP source to maintain the correct time on
the server. Configuring NTP should be done before video recording is
configured. The hardware clock should be set to use UTC time and the
appropriate time zone for the server. If you are using SUSE, you can use YaST
to configure the server time.
• The performance of client devices can vary depending on client configuration
and applications.
Obtaining VSVM Software
The VSVM software is available from
http://tools.cisco.com/support/downloads/pub/Redirect.x?mdfid=281550158
You must log in to the Cisco website to access the software. Select the Cisco
Video Surveillance Operations Manager software version for the appropriate for
your Linux version.
Installing VSVM
4
Installing and Upgrading Cisco Video Surveillance Virtual Matrix (VSVM)
Installing VSVM
Copy the downloaded .zip file with the VSVM software to the server and then
follow these steps:
Procedure
Step 1 Extract the contents of the downloaded .zip file. Cisco recommends that you
create a directory for the extracted contents.
shell> mkdir vsvm-6.1.0
shell> unzip Cisco_VSVM-6.1.0-xx-xxxxx.zip -d vsvm-6.1.0
Step 2 Verify that all files are present:
shell> cd vsvm-6.1.0
shell> ls -1
Cisco_VSBase-6.1.0-xx-xxxx-i586.rpm
Cisco_VSVM-6.1.0-xx.i586.rpm
Cisco_VSTools-6.1.0-noarch.rpm
Step 3 Install each of VSVM .rpm file:
shell> rpm -ivh Cisco_VSBase-6.1.0-xx-xxxxx-i586.rpm
shell> rpm -ivh Cisco_VSVM-6.1.0-xx-xxxxx-i586.rpm
shell> rpm -ivh Cisco_VSTools-6.1.0-noarch.rpm
5
Installing and Upgrading Cisco Video Surveillance Virtual Matrix (VSVM)
Configuring VSVM
Configuring VSVM
After you install VSVM, perform the following steps to use the Management
Console (VSMC) to set repositories for archives, clips and events. The VSMC
authentication information is:
Userid: root
password: secur4u
Procedure
Step 1 Open a web browser from a Windows PC and enter http://<server name/IP
address>/vsmc.html.
Step 2 Click the Virtual Matrix link to access the VSVM configuration. You are
prompted to authenticate.
Step 3 Enter the license key on the VSVM configuration page.
Step 4 Click Update.
Step 5 Click Restart Server, Restart Now, and Verify.
Upgrading VSVM
To upgrade VSVM, follow these steps:
Procedure
Step 1 Extract the contents of the downloaded .zip file. Cisco recommends that you
create a directory for the extracted contents.
shell> mkdir vsvm-6.1.0
shell> unzip Cisco_VSVM-6.1.0-xx-xxxxx-sp1.zip -d vsvm-6.1.0
Upgrading VSVM
6
Installing and Upgrading Cisco Video Surveillance Virtual Matrix (VSVM)
Step 2 Verify that all files are present:
shell> cd vsvm-6.1.0
shell> ls -1
Cisco_VSBase-6.1.0-xx-xxxx-i586.rpm
Cisco_VSVM-6.1.0-xx.i586.rpm
Cisco_VSTools-6.1.0-noarch.rpm
Step 3 Stop the VSVM service:
shell> /etc/init.d/cisco stop
Step 4 VSDrivers must be removed prior to uninstalling Cisco_VSVM. Uninstall all
previous MS modules including some (but not all) of the following based on the
previously installed version:
shell> rpm -e Cisco_VSTools
shell> rpm -e Cisco_VSVM
shell> rpm -e Cisco_VSBase
If the Cisco Video Surveillance Operations Manager (VSOM) is installed you
may get an error message when uninstalling the Cisco_VSBase package; to
uninstall the Cisco_VSBase package run
shell> rpm -e Cisco_VSBase --nodeps
This will leave the VSOM module installed.
Step 5 Run the following commands in the following order0:
shell> rpm -ivh Cisco_VSBase-6.1.0-xx-xxxxx-i586.rpm
shell> rpm -ivh Cisco_VSVM-6.1.0-xx-xxxxx-i586.rpm
shell> rpm -ivh Cisco_VSTools-6.1.0-noarch.rpm
Indice
Altri manuali Cisco Hardware di rete
Cisco
Cisco VPN 3002 Hardware Client Manager Manuale utente
Cisco
Cisco C7200-I - Input/Output Controller - Control... Manuale utente
Cisco
Cisco ONS 15310-MA SDH Manuale
Cisco
Cisco ONS 15327 Manuale dell'operatore
Cisco
Cisco Gigabit Switch Router Cisco 12012 Manuale utente
Cisco
Cisco NSS4100 - Gigabit Storage System Manuale di istruzioni
Cisco
Cisco Versatile Interface Processor (VIP6-80)... Manuale dell'operatore
Cisco
Cisco CRS-1 - Carrier Routing System Router Guida utente
Cisco
Cisco CVPN3015-NR - VPN Concentrator 3015 Manuale utente
Cisco
Cisco Cisco ONS 15600 SDH Manuale utente
Cisco
Cisco Fourth-Generation Versatile Interface Processor... Manuale dell'operatore
Cisco
Cisco Firepower 1010 Manuale utente
Cisco
Cisco DOC 785983 Manuale utente
Cisco
Cisco Wide Area Virtualization Engine 274 Manuale
Cisco
Cisco GS7000 Istruzioni operative
Cisco
Cisco TelePresence Manuale di servizio
Cisco
Cisco NCS 2000 series Manuale utente
Cisco
Cisco Firepower 1010 FPR1010-NGFW-K9 Manuale
Cisco
Cisco ESR-PRE2 Manuale utente
Cisco
Cisco Meraki MX68 Manuale
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
