Cisco 2524 - Router - EN Manuale utente

APPENDIX

Troubleshooting the Cisco 2524 and Cisco 2525 Routers B-1

Troubleshooting the Cisco 2524

and Cisco 2525 Routers

This appendix describes how to troubleshoot the Cisco 2524 and Cisco 2525 routers by

referring to the LEDs on the rear panel of the chassis (see Figure 1-2 and Figure 1-3) and

on the network processor modules (see Figure 1-4 through Figure 1-9).

The LEDs indicate the current operating condition of your router. You can observe the

LEDs, note any fault condition that the router is encountering, and then contact your system

administrator or a customer service representative, if necessary. Table B-1 describes the

LEDs on the router chassis and WAN modules.

Table B-1 LEDs

Chassis/Module LED State Description

Router chassis Power On steadily Power is being supplied to the router.

Off Power is not reaching the router. Verify that the power

supply is plugged into the wall receptacle, and that the

cable from the power supply to the router is connected.

Activity

(Ethernet/

Token Ring1)

Flickering The Ethernet/Token Ring LAN connection is

transmitting and receiving data normally.

Off The Ethernet/Token Ring LAN connection is not

transmitting or receiving data. Check the

Ethernet/Token Ring cable connection.

B-2 Cisco 2524 and Cisco 2525 Router User Guide

Router chassis Ethernet link

(Cisco 2524)2

On The router senses the Ethernet 10BaseT link integrity

signal, indicating normal operation.

Off The router is not sensing the Ethernet 10BaseT link

integrity signal. Check the Ethernet 10BaseT cable

connection.

In-ring

(Cisco 2525)

On The router has been successfully inserted into the

Token Ring, indicating normal operation.

Off The router has not been successfully inserted into the

Token Ring. Check the Token Ring cable connection.

2-wire switched 56-kbps,

4-wire 56/64-kbps, and

factional T1/T1 WAN

DSU/CSU modules

RX On Data is being received at the DTE interface.

TX On Data is transmitting from the DTE interface.

CD (Carrier) On The DSU/CSU in the module is communicating with

another DSU/CSU.

Loopback On The DSU/CSU is in loopback mode.

Alarm On An alarm condition is present.

Serial module Activity (serial

activity)

Flickering The serial WAN connection is transmitting and

receiving data normally.

Off The serial WAN connection is not transmitting or

receiving data. Check the serial cable connection.

ISDN BRI module Activity (ISDN

BRI activity)

Flickering The ISDN BRI WAN connection is transmitting and

receiving data normally.

Off The ISDN BRI WAN connection is not transmitting or

receiving data. Check the BRI cable connection.

ISDN BRI with integrated

NT1 module

ACT (ISDN

BRI activity)

Flickering The ISDN BRI (with integrated NT1) WAN

connection is transmitting and receiving data

normally.

NT1 On The router detects the ISDN link integrity signal at the

U interface3and the internal S/T interface4, indicating

that an ISDN connection has been established.

Chassis/Module LED State Description

Troubleshooting the Cisco 2524 and Cisco 2525 Routers B-3

Running Diagnostic Tests

If you have the fractional T1/T1 module, you can use external test equipment with the

monitor jack labeled OUT to monitor signals coming into the RJ-48C port, without

interrupting normal data transmission. You can use the monitor jack labeled IN to inject

data, which would interrupt normal data transmission.

Getting Help

For information on technical support, onsite service, and exchange and repair services, refer

to the Cisco Information Packet publication that shipped with your router.

ISDN BRI with integrated

NT1 module

Blinking

once per

second

The ISDN connection at the U interface is up, and the

internal S/T interface is coming up. If this state

persists, the ISDN port is either not configured or it is

configured incorrectly.

Blinking

eight times

per second

The ISDN connection at the U interface is coming up.

Off The router is not detecting the ISDN link integrity

signal. An ISDN connection has not been established.

Check the BRI cable connection.

1. The Token Ring activity LED is labelled ACT.

2. The Ethernet link LED is for the Ethernet 10BaseT port only; it does not work with the Ethernet AUI port.

3. The U interface is from the wall jack (telco interface) to the NT1 device.

4. The S/T interface is from the ISDN port on the module to the microprocessor.

Chassis/Module LED State Description

B-4 Cisco 2524 and Cisco 2525 Router User Guide

Getting Help

Altri manuali per 2524 - Router - EN

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Router di rete

Cisco

Cisco uBR924 Foglio di istruzioni

Cisco

Cisco NCS 5500 Series Manuale utente

Cisco

Cisco 1805 Manuale utente

Cisco

Cisco Firepower 1120 Manuale utente

Cisco

Cisco 2600 Series Manuale utente

Cisco

Cisco 12000 GSR Series Manuale di servizio

Cisco

Cisco NCS 6008 Manuale utente

Cisco

Cisco aironet 1240 Manuale

Cisco

Cisco ASR-920-20SZ-M Istruzioni operative e di sicurezza

Cisco

Cisco 1760 - VPN Bundle Router Manuale

Cisco

Cisco 7600-SIP-400 - SPA Interface Processor 400 Manuale utente

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Guida all'installazione

Cisco

Cisco 910 Manuale utente

Cisco

Cisco IR1101 Manuale utente

Cisco

Cisco Catalyst 2900 Series XL Manuale utente

Cisco

Cisco 2621 Manuale utente

Cisco

Cisco WS-C2950-24 Manuale utente

Cisco

Cisco RV130W Manuale di installazione e funzionamento

Cisco

Cisco CVR100W Manuale di istruzioni

Cisco

Cisco 7304 Series Istruzioni operative e di manutenzione

Cisco

Cisco ASR 920 series Manuale utente

Cisco

Cisco ASR 9000 Series Manuale utente

Cisco

Cisco 10000 Series Manuale utente

Cisco

Cisco 800 Series Come usare

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

EnGenius

EnGenius ESR-9710 Manuale utente

LevelOne

LevelOne FBR-1416 Manuale utente

Dynacord

Dynacord Promatrix 6000 Manuale utente

Lorex

Lorex F5D8230-4 Manuale utente