Cisco BTS 10200 Manuale utente

CISCO CONFIDENTIAL

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco BTS 10200 Softswitch

Cabling, VLAN, and IRDP Procedures

The purpose of this procedure is to explain how to:

•Cable a new Cisco BTS 10200 Softswitch system

•Provision the virtual local area network (VLAN) on the Cisco 2924M Ethernet Switches (hubs)

•Enable Internet Control Protocol (ICMP) Router Discovery Protocol (IRDP) functionality on the

Cisco BTS 10200 Softswitch and on the Cisco routers adjacent to the Cisco BTS 10200 Softswitch

This procedure is applicable to a Cisco BTS 10200 Softswitch with active and standby components

colocated in the same office.

Note This procedure is applicable only to systems with Continuous Computing hardware. If you are using

other hardware, contact your Cisco account team for procedures.

This procedure is not applicable to Cisco BTS 10200 Softswitch systems that are already in service.

Caution Do not use this procedure to change the cabling of an in-service Cisco BTS 10200 Softswitch, because

that will cause interruption of service. It is not necessary to change the cabling of in-service systems to

match this document.

Front View of Rack-Mounted Equipment

The front view of the standard Cisco BTS 10200 Softswitch system rack is shown in Figure 1 on page 2.

CISCO CONFIDENTIAL

OL-2906-01

Front View of Rack-Mounted Equipment

Figure 1 Standard Cisco BTS 10200 Softswitch Rack Conﬁguration

EMS B (AXi)

CCN node address = 1

PDU power feed 1A/1B

Call agent A (AXmp)

CCN node address =4

PDU power feed 5A/5B

Filler panel

(Expansion CA or Ext. FS)

Alarm panel, PDU power feed 8A

Call agent B (AXmp)

CCN node address = 2

PDU power feed 2A/2B

EMS A (AXi)

CCN node address = 3

PDU power feed 4A/4B

Filler panel

(Expansion CA or Ext. FS)

Filler panel

Ethernet switch (HUB) B (2924M)

PDU power feed 6A/6B

Ethernet switch (HUB) A (2924M)

PDU power feed 7A/7B

Filler panel

PDU (DC systems)

1U Filler panel

2.36 m

93 in. 48U

(ref)

69411

Filler panel

OFF

APP ALRM NOYES

CONS

OFF

RAPP ALRM

NOYES

CONS

OFF

RAPP ALRM

NOYES

CONS

OFF

APP ALRM NOYES

CONS

OFF

RAPP ALRM

NOYES

CONS

OFF

RAPP ALRM

NOYES

CONS

CISCO CONFIDENTIAL

OL-2906-01

Network VLAN Diagram

Figure 2 shows the physical interfaces and VLAN connections.

Figure 2 Network VLAN Diagram

Acronyms used in Figure 2:

EMS/BDMS = Element Management System/Bulk Data Management System

CA/FS = Call Agent/Feature Server

Comm. = communications over OMS Hub

NE = Network Element

SSH = Secure Shell

SFTP = Secure File Transfer Protocol (FTP)

DNS = Domain Name Server

VoIP = Voice over IP

IRDP = Internet Control Message Protocol (ICMP) Router Discovery Protocol

Notes for Figure 2:

1. For EMS/BDMS, qfe0 and qfe1 are also used for redundancy communication.

2. For CA/FS, qfe0 and qfe4 are also used for redundancy communication.

3. VLAN2 and VLAN6 are used primarily for VoIP signaling based on protocols such as MGCP, SIP,

H.323, and so forth.

87013

QFE0

HME0

QFE1

QFE2

QFE3

EMS redundancy/billing (2)

EMS redundancy/billing (1)

VoIP signaling, OMS Hub comm. (1)

CA/FS redundancy (1)

Billing (1)

CA-FS comm. (1)

QFE0

HME0

QFE1

QFE2

QFE3

CA/FS redundancy (2)

Billing (2)

CA-FS comm. (2)

QFE4

QFE5

QFE6

QFE7

EMS/BDMS Side A

CA/FS Side A Hub A

VLAN1

VLAN2

VLAN3

VLAN4

VLAN5

Hub B

VLAN6

VLAN7

VLAN8

VLAN9

Uplink for external access to hosts (connect to router).

Used for management services (SSH, SFTP, etc.)

and outbound billing data (FTP).

First uplink for external communications (connect to router).

Used for connection to external NEs and DNS services

via IRDP-enabled network.

HME0

EMS redundancy/billing (2)

EMS redundancy/billing (1)

CA/FS redundancy (1)

Billing (1)

CA-FS comm. (1)

HME0

CA/FS redundancy (2)

Billing (2)

CA-FS comm. (2)

EMS/BDMS Side B

CA/FS Side B

Data carried

Physical interface Second uplink for external communications (connect to router).

Used for connection to external NEs and DNS services

via IRDP-enabled network.

QFE0

QFE1

QFE2

QFE3

QFE0

QFE1

QFE2

QFE3

QFE4

QFE5

QFE6

QFE7

VoIP signaling, OMS Hub comm. (2)

VoIP signaling, OMS Hub comm. (1)

VoIP signaling, OMS Hub comm. (2)

Alarm panel

OMS Hub comm. (1)

Management services

OMS Hub comm. (2)

Management services

OMS Hub comm. (1)

OMS Hub comm. (2)

Management services

CISCO CONFIDENTIAL

OL-2906-01

Labeling the Cables

4. To support full system redundancy, it is necessary to connect each of the three

Cisco BTS 10200 Softswitch external uplinks to a different network with diverse routing paths to

the related external network elements (NEs) and services (such as OSS, DNS, media gateways, and

announcement servers).

Caution If each of the three external uplinks is not connected as described in Note #4, a single point of failure

could cause a traffic interruption.

5. To ensure redundancy of the DNS lookup function in the event of a network outage, it is strongly

recommended to have two DNS units reachable via separate networks with diverse routing paths.

Caution If both DNS servers become unreachable, a traffic interruption will occur.

Note Ethernet ports on the rear panels of some EMS and CA units are labeled ETH0, ZNB0, ZNB1, and so

forth. On some units these ports are labeled hme0, qfe0, qfe1, and so forth. Regardless of the labeling

style, the Cisco BTS 10200 Softswitch functionality is the same.

Labeling the Cables

Make sure that you have all the cables labeled before you begin. Label the cables according to the

procedure in Appendix A: Cable Labeling, page 22.

Connect Ethernet Cables To EMS and CA Units

Follow these steps to connect the Ethernet cables. Refer to Figure 1 on page 2 to identify the specific

units in the rack.

Step 1 Obtain the 10 Ethernet cables needed for connections between the rear panel of the Element

Management Systems (EMS A and EMS B) and the two Cisco 2924M Ethernet Switches (Hub A and

Hub B). These cables are listed in Table 1 in Appendix B: Cable List, page 23.

Step 2 Connect the 10 Ethernet cables to the ports on the rear panel of the EMS units as listed in Table 1 in

Appendix B: Cable List, page 23.

Figure 3 shows the rear view of the EMS. On the EMS, use ports ETH0 and ZNB0 through ZNB3.

Note Figure 3 and Figure 4 are not to scale.

CISCO CONFIDENTIAL

OL-2906-01

Connect CONSOLE Ethernet Cables to Alarm Panel

Figure 3 Partial Rear View of the EMS Unit Showing Ethernet Ports

Step 3 Obtain the 18 Ethernet cables needed for connections between the rear panel of the Call Agents (CA A

and CA B) and the two Cisco 2924M Ethernet Switches (Hub A and Hub B). These cables are listed in

Table 1 in Appendix B: Cable List, page 23.

Step 4 Connect the 18 Ethernet cables to the ports on the rear panel of the CA units as listed in Table 1 in

Appendix B: Cable List, page 23.

Figure 4 shows the rear view of the CA. On the CA, use ports ETH0 and ZNB0 through ZNB7.

Figure 4 Partial Rear View of the CA Unit Showing Ethernet Ports

Connect CONSOLE Ethernet Cables to Alarm Panel

Connect the two CONSOLE Ethernet cables from the Alarm Panel to the Hubs as described in this

section.

ZNB0 ZNB2

ZNB1 ZNB3

CCPU B CCPU A ETH0

EMS (AXi)

54352

ZNB4 ZNB5

ZNB1

CCPU B CCPU A ETH0

ZNB0

Call agent (AXmp)

54353

ZNB6 ZNB7

ZNB2 ZNB3

SPE2

SPE3

SPE0 SPE1

CISCO CONFIDENTIAL

OL-2906-01

Connect CCPUnet Cables and Terminating Resistors

Note These two CONSOLE cables are specially designed for the CONSOLE connections. Make sure

that you are using the correct cables.

Note One end of the CONSOLE cable is labeled “switch” and the other is labeled “net CCN”. The

“switch” end must connect to the Hub and the “net CCN” end must connect to the Alarm Panel.

Step 1 Refer to Figure 1 on page 2 to identify which Cisco 2924M Ethernet Switch (Hub) is designated

Ethernet Switch A and which is Ethernet Switch B.

Step 2 Connect the “net CCN” end of a CONSOLE cable to port SER 1 on the Alarm Panel, and the “switch”

end to the CONSOLE port on the rear panel of Ethernet switch (Hub) A.

Step 3 Connect the “net CCN” end of a CONSOLE cable to port SER 2 on the Alarm Panel, and the “switch”

end to the CONSOLE port on the rear panel of Ethernet switch (Hub) B.

The rear view of the alarm panel is shown in Figure 5. (The drawing is not to scale.)

Figure 5 Rear View of Alarm Panel

Connect CCPUnet Cables and Terminating Resistors

Follow these steps to connect the intershelf signaling (CCPUnet) cables and terminating resistors:

Step 1 Obtain the eight CCPUnet cables (four for CCPU A and four for CCPU B).

Step 2 Connect the CCPUnet cables between the machines as listed in Table 1 on page 23. Make sure that you

connect cables labeled CCPU A to the CCPU A ports, and cables labeled CCPU B to the CCPU B

ports.

Note Refer to Figure 3 through Figure 5 to locate the CCPU ports on the rear panels.

Step 3 Connect the two terminating resistors (part # CCPU 012 02150-02602 REV 00) to the Alarm Panel

(Figure 5) as follows: Connect one resistor to CCPUNet HUB A port 5, and the other resistor to

CCPUNet HUB B port 5.

CCPUNet HUB A

CCPUNet HUB B

LINE

REM

SER 1

SER 2

SER 3

SER 4

SER 5

SER 6

SER 7

SER 8

SER 9

SER 10

SER 11

SER 12

CONS

COM1

eth1

eth0

I/O CABLE A

I/O CABLE B

-48V A -48V B

100-240V-

50-60 HZ 40W

AC IN

69752

12345678

CISCO CONFIDENTIAL

OL-2906-01

Connect External Network Uplink Cables to Ethernet Switches

Follow these steps to connect the external network uplink cables to the Ethernet switches:

Step 1 Refer to Figure 1 on page 2 to identify which Cisco 2924M Ethernet Switch is designated Ethernet

Switch A and which is Ethernet Switch B.

Step 2 If your local network documentation calls for gigabit Ethernet, contact Cisco TAC for assistance.

Step 3 If your local network documentation calls for 100 Mb Ethernet, connect the applicable network uplink

cables as listed in Table 1. Ports #21 through 24 are available for this use.

Step 4 After installing the uplink cables, record the necessary information on a copy of Table 1 or similar

document according to local procedures.

Connect SS7 Signaling Cables To CA

Follow these steps to connect the SS7 signaling cables to the CA units of the

Cisco BTS 10200 Softswitch:

Step 1 Refer to Figure 1 on page 2 to identify which unit is CA A and which is CA B.

Step 2 Connect T1 cables for SS7 signaling to the SPE0 and SPE1 connectors on CA A (see Figure 6).

Note SPE2 and SPE3 are not used.

Step 3 Connect T1 cables for SS7 signaling to the SPE0 and SPE1 connectors on CA B.

Step 4 Route the other ends of these T1 cables as specified in local network documentation, and add (write in)

this information on a copy of Table 1 or similar document.

CISCO CONFIDENTIAL

OL-2906-01

Connect Internal Power and Grounding Cables

Figure 6 Location of SPE0 and SPE1 Connectors on CA Backplane

Connect Internal Power and Grounding Cables

After obtaining approval from a supervisor, an authorized power installer should follow these steps to

connect DC power cables and ground cables from the power distribution unit (PDU) to the other devices

in the Cisco BTS 10200 Softswitch rack.

Note If you need to connect an AC system, contact your Cisco account team for assistance.

Step 1 Connect the intershelf DC power cables from the PDU to each of the devices in the rack. See Table 1 on

page 23 for the complete cabling list.

54355

Call agent (AXmp)

Location of SPE0

and SPE1 connectors

(Used for SS7 signaling)

ZNB4 ZNB5

ZNB1

CCPU B CCPU A ETH0

ZNB0

ZNB6 ZNB7

ZNB2 ZNB3

SPE2

SPE3

SPE0 SPE1

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. To see translations of the warnings that appear in

this publication, refer to the translated safety warnings that accompanied this device.

Note: SAVE THESE INSTRUCTIONS

Note: This documentation is to be used in conjunction with the specific product installation guide

that shipped with the product. Please refer to the Installation Guide, Configuration Guide, or other

enclosed additional documentation for further details.

CISCO CONFIDENTIAL

OL-2906-01

Connect Site Power and Grounding Cables To PDU

Step 2 Following local electrical codes, connect the ground cables from each of the devices in the rack to the

PDU grounding point (either of the two grounding screws on the PDU rear panel). See Table 1 for the

complete cabling list.

Connect Site Power and Grounding Cables To PDU

After obtaining approval from a supervisor, an authorized power installer should follow these steps to

connect the DC power from the office batteries to the PDU.

Note For DC systems the nominal current rating for a complete Cisco BTS 10200 Softswitch system

is 26A at -48 VDC, and the maximum current rating is 40A at -48 VDC.

Note If you need to connect an AC system, contact your Cisco account team for assistance.

Step 1 Following local electrical codes, connect power cables from the power distribution unit (PDU) to dual

feeds (“A” and “B”) on the office batteries. Use Listed two-hole crimped lugs on the PDU side of the

cable.

Step 2 Following local electrical codes, connect the PDU grounding point (both of the two grounding screws

on the PDU rear panel) to CO earth ground using 6 AWG wire or heavier and a Listed two-hole crimped

lug.

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in

the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable grounding is available.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. To see translations of the warnings that appear in

this publication, refer to the translated safety warnings that accompanied this device.

Note: SAVE THESE INSTRUCTIONS

Note: This documentation is to be used in conjunction with the specific product installation guide

that shipped with the product. Please refer to the Installation Guide, Configuration Guide, or other

enclosed additional documentation for further details.

CISCO CONFIDENTIAL

OL-2906-01

Connect Site Power and Grounding Cables To PDU

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in

the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable grounding is available.

Altri manuali per BTS 10200

Indice

Altri manuali Cisco Interruttore

Cisco

Cisco Cisco Line Card 4500 E-Series Manuale utente

Cisco

Cisco RSP8 Manuale dell'operatore

Cisco

Cisco 110 Series Manuale utente

Cisco

Cisco InfiniBand SFS 7000 Manuale utente

Cisco

Cisco AP776A - Nexus Converged Network Switch 5020 Manuale utente

Cisco

Cisco HWIC-4ESW - EtherSwitch HWIC Switch Manuale

Cisco

Cisco Nexus 9000 Series Manuale utente

Cisco

Cisco OL-4419-06 Manuale utente

Cisco

Cisco CATALYST 6500 WS-X6066-SLB-S-K9 Manuale di installazione e funzionamento

Cisco

Cisco Catalyst 3920 Manuale utente

Cisco

Cisco WS-C2950-12 Manuale utente

Cisco

Cisco Catalyst 2900 Series Manuale utente

Cisco

Cisco MGX 8850 Manuale dell'operatore

Cisco

Cisco MDS 9000 Series Manuale utente

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Manuale di istruzioni

Cisco

Cisco Nexus 5000 Series Manuale utente

Cisco

Cisco WS-C3750G-48PS-S Manuale elenco delle parti

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manuale utente

Cisco

Cisco MGX 8950 Istruzioni operative e di sicurezza

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manuale utente

Cisco

Cisco SF250-48HP Manuale utente

Cisco

Cisco NMH Series Manuale utente

Cisco

Cisco ME 3400 Series Manuale utente

Cisco

Cisco MDS 9700 Series Manuale di istruzioni

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente