Cisco Catalyst 3750E-48PD-F Manuale utente

Getting Started Guide

Catalyst 3750-E Switch Getting Started Guide

INCLUDING LICENSE AND WARRANTY

1About this Guide

2Taking Out What You Need

3Running Express Setup

4Managing the Switch

5Planning Switch Stacks

6Rack-Mounting

7Connect to the Switch Ports

8In Case of Difficulty

9Obtaining Documentation

10 Obtaining Technical Assistance

11 Cisco 90-Day Limited Hardware Warranty Terms

1 About this Guide

This guide provides instructions on how to use Express Setup to initially configure your Catalyst

switch. Also covered are switch management options, basic rack-mounting procedures, stacking

procedures, port and module connection procedures, and troubleshooting help.

For additional installation and configuration information for Catalyst 3750-E switches, see the

Catalyst 3750-E documentation on Cisco.com. For system requirements, important notes, limitations,

open and resolved bugs, and last-minute documentation updates, see the release notes, also on

Cisco.com.

When using the online publications, refer to the documents that match the Cisco IOS software version

running on the switch. The software version is on the Cisco IOS label on the switch rear panel.

You can order printed copies of the manuals from the Cisco.com sites and from the telephone numbers

listed in the “Obtaining Documentation” section on page 24.

For translations of the warnings that appear in this publication, see the Regulatory Compliance and

Safety Information for the Catalyst 3750-E and Catalyst 3560-E Switch that accompanies this guide.

2 Taking Out What You Need

Follow these steps:

1. Unpack and remove the switch and the accessory kit from the shipping box.

2. Return the packing material to the shipping container, and save it for future use.

3. Verify that you have received the items shown on page 3. If any item is missing or damaged,

contact your Cisco representative or reseller for instructions. Some switch models might include

additional items that are not shown on page 3.

4. For switches with the optional 1150-W power supply module (model C3K-PWR-1150WAC),

install the power supply in the switch as described in the installation notes after you rack-mount

the switch.

Shipping Box Contents

Catalyst 3750E-48 Power over Ethernet

(PoE) switch 8Four rubber mounting feet

2Documentation 9Power cord retainer

3AC power cord 10 Four number-12 Phillips machine screws

4Console cable 11 Twelve number-8 Phillips flat-head screws

StackWise cable, 0.5-meter, 1-meter or

3-meter1

1. (0.5-meter supplied when not specified)

12 One black Phillips machine screw

6Two 19-inch mounting brackets 13 Ground lug screw and ring terminal

7Cable guide

Regulatory Compliance

and Safety Information

GettingStarted Guide

MODE

SYST

RPS

MASTR

STAT

DUPLX

SPEED

PoE

STACK

X2-1

X2-2

3738399404142434445464748

37X47X

38X48X

252627282930313233343536

25X35X

26X36X

131415161718192021222324

13X23X

14X24X

123456789101112

1X11X

2X12X

Catalyst 3750-E

SERIES

PoE-48

1 2

3 4 5

6 7 8

11 12 13

157636

Cisco

Product Ownership

Registration card

3 Running Express Setup

When you first set up the switch, you should use Express Setup to enter the initial IP information.

Doing this enables the switch to connect to local routers and the Internet. You can then access the

switch through the IP address for further configuration.

You need this equipment to set up the switch:

•A PC with Windows 2000 or XP installed.

•A web browser (Internet Explorer 5.5, 6.0, Netscape 7.1 or later) with JavaScript enabled.

•A straight-through or crossover Category 5 Ethernet cable to connect your PC to the switch.

Disable any pop-up blockers or proxy settings in your browser software and any wireless client

running on your PC.

To run Express Setup:

Step 1 Make sure that nothing is connected to the

switch.

During Express Setup, the switch acts as a

DHCP server. If your PC has a static IP

address, change your PC settings before you

begin to temporarily use DHCP.

Step 2 Power the switch.

For AC-powered switches, connect the AC

power cord to the switch power supply and

to a grounded AC outlet.

For DC-powered switches, see the wiring

instructions in the hardware installation

guide on Cisco.com.

Step 3 When the switch powers on, it begins the power-on self-test (POST). During POST, the

LEDs blink while tests verify that the switch functions properly.

Wait for the switch to complete POST, which can take several minutes.

Step 4 Verify that POST has completed by confirming that the SYST LED remains green. If the

switch fails POST, the SYST LED turns amber. See the “In Case of Difficulty” section on

page 22 if your switch fails POST.

MODE

SYST

RPS

MASTR

STAT

DUPLX

SPEED

PoE

STACK

X2-1

X2-2

37 38 399 40 41 42 43 44 45 46 47 48

37X47X

38X48X

25 26 27 28 29 30 31 32 33 34 35 36

25X35X

26X36X

13 14 15 16 17 18 19 20 21 22 23 24

13X23X

14X24X

12345678910 11 12

1X11X

2X12X

Catalyst3750-E

SERIES

PoE-48

ACOKPSOK

100-240V~

1.0-5A

50-60HZ

Step 5 Press and hold the Mode button for

3 seconds. When all of the LEDs above the

Mode button turn green, release the Mode

button.

Step 6 If the LEDs above the Mode button blink after you press the button, release it. Blinking

LEDs mean that the switch is already configured and cannot go into Express Setup mode.

For more information, see the “Resetting the Switch” section on page 23.

Step 7 Verify that the switch is in Express Setup mode. Make sure that all LEDs above the Mode

button are green. (On some switch models, the RPS LED remains off.)

Step 8 Connect a Category 5 Ethernet cable to any

10/100/1000 Ethernet port on the switch

front panel or to the Ethernet management

port on the rear panel. Connect the other end

of the cable to the Ethernet port on your PC.

Step 9 Verify that the LEDs on both Ethernet ports are green.

Wait 30 seconds.

Step 10 Launch a web browser on your PC. Enter the

IP address 10.0.0.1 in the web browser, and

press Enter.

MODE

SYST

RPS

MASTR

STAT

DUPLX

SPEED

PoE

STACK

X2-1

X2-2

37 38 399 40 41 42 43 44 45 46 47 48

37X47X

38X48X

25 26 27 28 29 30 31 32 33 34 35 36

25X35X

26X36X

13 14 15 16 17 18 19 20 21 22 23 24

13X23X

14X24X

12345678910 11 12

1X11X

2X12X

Catalyst3750-E

SERIES

PoE-48

MODE

SYST

RPS

MASTR

STAT

DUPLX

SPEED

PoE

STACK

MODE

SYST

RPS

MASTR

STAT

DUPLX

SPEED

PoE

STACK

X2-1

X2-2

3738399404142434445464748

37X47X

38X48X

252627282930313233343536

25X35X

26X36X

131415161718192021222324

13X23X

14X24X

123456789101112

1X11X

2X12X

Catalyst3750-E

SERIES

PoE-48

Step 11 The Express Setup Basic Settings page appears. If it does not appear, see the “In Case of

Difficulty” section on page 22.

Step 12 Enter this information in the Network Settings fields:

•In the Management Interface (VLAN ID) field, the default is 1. Enter a new VLAN ID

only if you want to change the management interface through which you manage the

switch. The VLAN ID range is 1 to 1001.

•In the IP Address field, enter the IP address of the switch. In the IP Subnet Mask field,

click the drop-down arrow, and select an IP Subnet Mask.

•In the Default Gateway field, enter the IP address for the default gateway (router).

•Enter your password in the Switch Password field. The password can be from 1 to 25

alphanumeric characters, can start with a number, is case sensitive, allows embedded

spaces, but does not allow spaces at the beginning or end. In the Confirm Switch

Password field, enter your password again.

Step 13 (Optional) Enter this information in the Ethernet Management Port Settings fields:

•In the IP Address field, enter the IP address of the Ethernet management port. In the

IP Subnet Mask field, click the drop-down arrow, and select an IP Subnet Mask.

Step 14 (Optional) You can enter the Optional Settings information now or enter it later by using

the device manager interface:

•In the Host Name field, enter a name for the switch. The host name is limited to 31

characters; embedded spaces are not allowed.

•Enter the date, time, and time zone information in the System Date, System Time, and

Time Zone fields. Click Enable to enable daylight saving time.

Step 15 (Optional) You can select the Advanced Settings tab on the Express Setup window and enter

the advanced settings now or enter them later by using the device manager interface.

Step 16 (Optional) Enter this information in the Advanced Setting fields:

•In the Telnet Access field, click Enable if you are going to use Telnet to manage the

switch by using the command-line interface (CLI). If you enable Telnet access, you must

enter a Telnet password.

•In the Telnet Password field, enter a password. The Telnet password can be from 1 to

25 alphanumeric characters, is case sensitive, allows embedded spaces, but does not

allow spaces at the beginning or end. In the Confirm Telnet Password field, re-enter the

Telnet password.

•In the SNMP field, click Enable to enable Simple Network Management Protocol

(SNMP). Enable SNMP only if you plan to manage switches by using CiscoWorks 2000

or another SNMP-based network-management system.

•If you enable SNMP, you must enter a community string in the SNMP Read Community

field, the SNMP Write Community field, or both. SNMP community strings

authenticate access to MIB objects. Embedded spaces are not allowed in SNMP

community strings. When you set the SNMP read community, you can access SNMP

information, but you cannot change it. When you set the SNMP write community, you

can both access and change SNMP information.

•In the System Contact and System Location fields, enter a contact name and the wiring

closet, floor, or building where the switch is located.

Step 17 (Optional) You can enable IPv6 on the switch in the Advanced Settings screen. In the Enable

IPv6 field, click Enable to enable IPv6 on the switch. Note: Enabling IPv6 restarts the switch

when you complete Express Setup.

Refreshing the PC IP Address

After you complete Express Setup, you should refresh the PC IP address:

•For a dynamically assigned IP address, disconnect the PC from the switch, and reconnect the PC

to the network. The network DHCP server assigns a new IP address to the PC.

•For a statically assigned IP address, change it to the previously configured IP address.

4 Managing the Switch

After you complete Express Setup and install the switch in your network, use the device manager or

other management options described in this section for further configuration.

Using the Device Manager

The simplest way to manage the switch is by using the device manager that is in the switch memory.

This is a web interface that offers quick configuration and monitoring. You can access the device

manager from anywhere in your network through a web browser.

Follow these steps:

1. Launch a web browser on your PC or workstation.

2. Enter the switch IP address in the web browser, and press Enter. The device manager page appears.

3. Use the device manager to perform basic switch configuration and monitoring. Refer to the device

manager online help for more information.

4. For more advanced configuration, download and run the Cisco Network Assistant, which is

described in the next section.

Step 18 To complete Express Setup, click Submit in the Network Settings or the Advanced Settings

screen to save your settings. Click Cancel to clear your settings.

When you click Submit, the switch is configured and exits Express Setup mode. The PC

displays a warning message and then tries to connect with the new switch IP address. If you

configured the switch with an IP address that is in a different subnet from the PC,

connectivity between the PC and the switch is lost. If you enabled IPv6, the switch restarts.

Step 19 Disconnect the switch from the PC, and install the switch in your production network. See

the “Managing the Switch” section on page 8 for information about configuring and

managing the switch.

If you need to rerun Express Setup, see the “Resetting the Switch” section on page 23.

Downloading Cisco Network Assistant

Cisco Network Assistant is a software program that you download from Cisco.com and run on

your PC. It offers advanced options for configuring and monitoring multiple devices, including

switches, switch clusters, switch stacks, routers, and access points. Network Assistant is free—there is

no charge to download, install, or use it.

Follow these steps:

1. Go to this Web address: http://www.cisco.com/go/NetworkAssistant.

You must be a registered Cisco.com user, but you need no other access privileges.

2. Find the Network Assistant installer.

3. Download the Network Assistant installer, and run it. (You can run it directly from the Web if

your browser offers this choice.)

4. When you run the installer, follow the displayed instructions. In the final panel, click Finish to

complete the Network Assistant installation.

Refer to the Network Assistant online help and the getting started guide for more information.

Command-Line Interface

You can enter Cisco IOS commands and parameters through the CLI. Access the CLI by connecting

your PC directly to the switch console port or to the Ethernet management port.

Using the switch console port:

Follow these steps:

1. Connect the supplied RJ-45-to DB-9 adapter cable to the standard 9-pin serial port on the PC.

Connect the other end of the cable to the console port on the switch.

2. Start a terminal-emulation program on the PC.

3. Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit,

and no flow control.

4. Use the CLI to enter commands to configure the switch. See the software configuration guide and

the command reference for more information.

Using the switch Ethernet management port:

Follow these steps:

1. Connect a Category 5 Ethernet cable to the PC Ethernet port. Connect the other end of the cable

to the Ethernet management port on the switch rear panel.

2. Start a Telnet session on the PC.

3. Enter the switch IP address that you assigned by using Express Setup.

4. Use the CLI to enter commands to configure the switch. See the software configuration guide and

the command reference for more information.

Other Management Options

You can use SNMP management applications such as CiscoWorks Small Network Management

Solution (SNMS) and HP OpenView to configure and manage the switch. You also can manage it

from an SNMP-compatible workstation that is running platforms such as HP OpenView or

SunNet Manager.

The Cisco IE2100 Series Configuration Registrar is a network management device that works with

embedded Cisco Networking Services (CNS) agents in the switch software. You can use IE2100 to

automate initial configurations and configuration updates on the switch.

See the “Accessing Help Online” section on page 23 for a list of supporting documentation.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Interruttore

Cisco

Cisco Linksys NMH300 Manuale utente

Cisco

Cisco WS X4148 RJ21 - Catalyst 4000 Series 10/100 Telco... Manuale utente

Cisco

Cisco Catalyst Series Switch 2940 Manuale utente

Cisco

Cisco ME 3400 Series Manuale

Cisco

Cisco CSS11501 - 100Mbps Ethernet Load Balancing... Manuale utente

Cisco

Cisco Catalyst 3030 Manuale di installazione

Cisco

Cisco Catalyst 4507R-E Manuale

Cisco

Cisco CSS5 SSL K9 - Syst. CSS11500 SSL MODULE Manuale

Cisco

Cisco 8800 Series Manuale

Cisco

Cisco 3750 - Catalyst EMI Switch Manuale utente

Cisco

Cisco Nexus 7000 Series Manuale utente

Cisco

Cisco Catalyst X6148 Manuale operativo e di manutenzione

Cisco

Cisco Nexus 92348GC-X NX-OS Manuale

Cisco

Cisco WS-C3750G-48PS-S Manuale elenco delle parti

Cisco

Cisco Nexus 5000 Series Manuale utente

Cisco

Cisco Cisco Industrial Ethernet 3000 Series Manuale utente

Cisco

Cisco ASR 5000 Series Manuale

Cisco

Cisco MERAKI MS355 Series Manuale utente

Cisco

Cisco WS-C3560X-48PF-L Manuale

Cisco

Cisco Catalyst 4500 Series Guida utente

Cisco

Cisco CATALYST 5002 Manuale utente

Cisco

Cisco Nexus 93180YC-FX3S Manuale utente

Cisco

Cisco ASR 900 Series Manuale utente

Cisco

Cisco Nexus 93240YC-FX2 Manuale

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente