Cisco Catalyst 6840 Series Istruzioni operative

Troubleshooting

Problems with the initial startup are often caused by a switching module that has become dislodged from the

backplane or a power supply that has been disconnected from the power cord connector. Although temperature

conditions above the maximum acceptable level rarely occur at initial startup, you might encounter these

conditions during extended operation. Long-term monitoring functions also include independent reporting of

DC-output voltage problems.

•Getting Started, on page 1

•Solving Problems at the System Component Level, on page 1

•Identifying Startup Problems, on page 2

•Troubleshooting the Power Supply, on page 2

•Troubleshooting the Fan Tray , on page 3

•Status LED Indicators, on page 4

•Contacting Cisco Customer Service, on page 4

•Finding the Serial Number, on page 5

Getting Started

When the initial system startup is complete, verify the following:

• Power supplies are supplying power to the system.

• The fan tray assembly is operating.

• System software boots successfully.

If one or more of the above conditions are not met, use the procedures described in this chapter to isolate and,

if possible, resolve the problem. If all of the above conditions are met, and the hardware installation is complete,

refer to your software release notes for hardware support information and software caveats.

Solving Problems at the System Component Level

The key to success when troubleshooting the system is to isolate the problem to a specific system component.

The first step is to compare what the system is doing to what it should be doing. Because a startup problem

can usually be attributed to a single component, it is more efficient to isolate the problem to a subsystem rather

than troubleshoot each separate component in the system.

Troubleshooting

The switch consists of these subsystems:

• Power supplies

• Fan tray assembly

The chassis fan tray assembly should operate whenever system power is on. You should see the FAN

LED turn green and hear the fan tray assembly operating. A amber FAN LED indicates that one or more

fans in the fan tray assembly is not operating. You should immediately contact a Customer Service

representative if the fan tray assembly is not functioning properly. There are no installation adjustments

that you can make if the fan tray assembly does not function properly at initial startup.

Identifying Startup Problems

LEDs indicate all system states in the startup sequence. By checking the LEDs, you can determine when and

where the system failed in the startup sequence.

Procedure

Step 1 Turn on the power supplies. You should immediately hear the system fan tray assembly begin to operate.

• If you determine that the power supplies are functioning normally and that the fan tray assembly is faulty,

contact a customer service representative.

Step 2 If the startup information and system banner do not display at startup, verify that the terminal is set correctly

and that it is connected properly to the console port.

Troubleshooting the Power Supply

If the OK LED does not light after you turn on the power switch, follow these steps to isolate a power subsystem

problem:

Procedure

Step 1 Verify that the OK LED on the power supply is green.

• If the OK LED is green, the AC or DC source is good and the power supply is functional.

• If the OK LED remains off, there might be a problem with the AC source, the DC source, or the power

cable.

• Turn off the power to the switch, connect the power cord to another power source if one is available, and

turn on the power.

• If the OK LED is green, the problem is the first power source.

• If the OK LED fails to light after you connect the power supply to a new power source, replace the power

cord, and turn on the switch.

Troubleshooting

Identifying Startup Problems

• If the OK LED then goes on, return the first power cord for replacement.

If this unit has more than one power cord, repeat Step 1 for each power supply.

If the OK LED still fails to light when the switch is connected to a different power source with a new power

cord, the power supply is probably faulty.

If a second power supply is available, install it in the second power supply bay, and contact a customer service

representative for further instructions.

Step 2 If you have a second power supply, repeat Step 1 for this power supply.

What to do next

If you are unable to resolve the problem or if you determine that either a power supply or backplane connector

is faulty, see Contacting Cisco Customer Service, on page 4.

Troubleshooting the Fan Tray

To isolate a fan tray problem, follow these steps:

Procedure

Step 1 Verify that the FAN LED on the fan tray is green.

If the FAN LED is not green, see Contacting Cisco Customer Service, on page 4 to determine whether or

not the power subsystem is functioning properly.

Step 2 Check to determine if the FAN LED is amber. If the FAN LED is amber, the fan tray is not seated in the

backplane or has malfunctioned.

Do the following:

• To ensure that the fan tray is seated properly, loosen the captive installation screws, remove the fan tray,

and reinstall it.

• Tighten all captive installation screws, and then restart the system.

• If the FAN LED is still amber, the system detects an individual fan failure. Contact a customer service

representative for instructions.

Troubleshooting

Troubleshooting the Fan Tray

Status LED Indicators

ActionComponentAlarm TypeStatus LED

Indication

Syslog message and SNMP trap

generated.

If redundancy is configured, the

system switches to the redundant

supervisor engine and the active

supervisor engine shuts down.

If there is no redundancy and the

overtemperature condition is not

corrected, the system shuts down

after 5 minutes.

Chassis temperature sensor

exceeds major threshold.

MajorRed

Syslog message and SNMP trap

generated.

Monitor the condition.

Chassis temperature sensor

exceeds minor threshold.

MinorOrange

Syslog message and SNMP trap

generated.

If major alarm and the

overtemperature condition is not

corrected, the system shuts down

after 5 minutes.

If minor alarm, monitor the

condition.

Redundant supervisor engine

temperature sensor exceeds

major or minor threshold.

Major

Minor

Red

Orange

Contacting Cisco Customer Service

If you are unable to solve a startup problem after using the troubleshooting suggestions in this chapter, contact

a Cisco customer service representative for assistance and additional instructions. Before you call, have the

following information ready to help your service provider assist you as quickly as possible:

• Date on which you received the switch

• Chassis serial number

• Type of software and release number

• Maintenance agreement or warranty information

• Brief description of the problem

• Brief explanation of the steps you have already taken to isolate and resolve the problem

Troubleshooting

Status LED Indicators

Finding the Serial Number

If you contact Cisco Technical Assistance, you need to know the switch serial number. The figure shows

where the serial number is located. You can also use the show version privileged EXEC command to see the

serial number.

Figure 1: Serial Number on the Chassis

Troubleshooting

Finding the Serial Number

Troubleshooting

Finding the Serial Number

Altri manuali per Catalyst 6840 Series

Indice

Altri manuali Cisco Interruttore

Cisco

Cisco Catalyst 3560-24PS Manuale utente

Cisco

Cisco Catalyst 3750G-24TS Manuale operativo e di manutenzione

Cisco

Cisco IE 3000 Manuale utente

Cisco

Cisco Nexus 9200 Series Manuale utente

Cisco

Cisco WS-C2940-8TT-S Manuale

Cisco

Cisco Catalyst 2960 Series Manuale utente

Cisco

Cisco Catalyst X6148 Manuale operativo e di manutenzione

Cisco

Cisco MS225-24 Manuale utente

Cisco

Cisco MDS 9000 Series Manuale utente

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Manuale di istruzioni

Cisco

Cisco Nexus 5548UP Manuale utente

Cisco

Cisco CSS 11801 Manuale utente

Cisco

Cisco 2960-48TC - Catalyst Switch Manuale

Cisco

Cisco 1503 Istruzioni per il montaggio

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manuale di installazione e funzionamento

Cisco

Cisco 100 Series Manuale utente

Cisco

Cisco Catalyst 3560-X-24P Manuale utente

Cisco

Cisco Catalyst 3040 Manuale utente

Cisco

Cisco 4948 Series Manuale utente

Cisco

Cisco Nexus 7706 Manuale

Cisco

Cisco Catalyst 2960-L Manuale

Cisco

Cisco SFS 7008 Istruzioni per l'installazione

Cisco

Cisco ESW 500 Series Manuale utente

Cisco

Cisco MGX 8850 Manuale di installazione

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente